Home - De Raat
Home - De Raat
Instruction Manual for MetaCel models including: MC-40PR Finger Print, MC-40PR, Finger Print, Print
١٣/٠٦/٢٠٢٤ — When using 2 user codes: When using 1 user code: Register fingerprint ... Use the “ON/OFF” switch on the alarm to control the alarm. 2. Use 3 x 1.5V ...
De Raat Metacel MC40PR Grey Fire Safe | Safe.co.uk
De Raat Metacel MC20PR Grey Fire Safe | Safe.co.uk
File Info : application/pdf, 5 Pages, 861.56KB
DocumentDocumentMetaCel Fingerprint Please make sure you read this manual, before using your safe. Safe overview Keypad overview Opening the safe Press "START" 1. Main body 2. Pull-out drawer 3. Shelf (MC-40 only) 4. "S" Memory button "B" (Not in use) "W" (Not in use) 5. Door sensor 6. LED light 7. Battery case 8. Alarm 9. Lock bolt 1. LCD Display 2. Touch keypad 3. START button 4. Fingerprint lock 5. USB-C port Enter passcode Initial code: 123456 Press "START" Pull the door Changing the passcode When using 2 user codes: When using 1 user code: Register fingerprint (max. 10 fingerprints possible) Deleting fingerprint Replace batteries immediately when: · Screen displays "Lo_bAt." · Safe door fails to open when "OPEn" message appears after passcode is entered. · "good" appears on display along with "beep beep" sound after passcode is entered. · screen fails to turn on after you press "START" button. · touch button is not clear enough. · there is no response or malfunction. Micro USB `C' type port In case the internal batteries are used up, you can use the micro USB-C port to give enough power to the lock to open the door. How do I replace the batteries? 1. Open the safe door. 2. Open the battery compartment. You will find this compartment on the inside of the door (position 7 on the drawing on page 1 of this manual). 3. Replace the batteries. Use 1.5V alkaline batteries (AA x4). 4. Proper insertion of the batteries is confirmed once screen displays "good" message and a beep is heard. Emergency code (E-CodE) Since the safe is not for IOT, emergency code will not transmit any messages to a 3rd party. If you unintentionally register the emergency code (E-CODE), please make sure it is the same as your passcode to avoid any confusion. Pressing the "S" button shortly twice will lead to the E-CODE registering mode. Keypad lock mode 1. Activate Press "START" for more than 10 seconds until "Act" appears. "Act" message signifies activation of keypad lock mode. Any keypad input will only display "ACT". 2. Deactivate To deactivate keypad lock mode, press "START" for more than 3 seconds until "dEAct" appears. Volume control Security mode Press the "START" button twice to hide the passcode on the display. Passcode displayed Passcode not displayed How to use the alarm 1. Use the "ON/OFF" switch on the alarm to control the alarm. 2. Use 3 x 1.5V AAA batteries. When there is external impact or the safe is tilted, the alarm will go off (120dB sound). After 10 seconds from turning on the switch, the alarm is ready to operate. There is a light detecting sensor connected to the alarm. The alarm will be off when you open the door. Volume displayed Emergency key Note: 1. The emergency key is used to temporarily open the safe door in case the safe is inoperable. It is recommended not to use the master key in general usage of the safe. 2. The emergency key is a security device that can open the safe without entering a registered passcode. It is notified that the customer is responsible for the loss or theft of the emergency key. Please do not put the emergency key in the safe, but keep the keys in a different secure place. How to open the safe with the emergency key 1. Remove a square-shaped cover by pulling out the small hole on it. Clip or needle can be used. The square-shaped cover is on the front left side of the safe. Pull it out completely using a ball pen or a clip. 2. Insert the emergency key into the hole. Place the emergency key groove direction upward and insert it all the way into the hole. Pay attention to the direction of the groove and check if it is completely inserted. Location of the emergency key hole 3. Unlock the emergency key by rotating it 120 degrees clockwise. If the emergency key groove direction is 120 degrees downward, the door can be opened. Caution: when rotating the emergency key, do not forcefully turn it, please turn it slowly. There is a risk of damage if the emergency key is turned excessively. Position of the key 4. To use the door as usual after opening the door using the emergency key: - Rotate the emergency key 120 degrees counterclockwise. - Remove the emergency key and put the cover again. When an Err-05 message is displayed, enter the correct passcode or fingerprint to settle the error message. Placing emergency key in key hole Turning the emergency key clockwise Trouble shooting De Raat Security Products BV Edelgasstraat 5 2718 SX Zoetermeer Nederland +31 (0) 79 361 52 36 verkoop@deraat.nl www.deraat.eu De Raat Security Products NV Gareelmakersstraat 10 2200 Herentals België +32 (0) 14 232371 info@deraat.be www.deraat.eu De Raat Security Products Ltd. Unit 32 Axis Park Manasty Road Orton Southgate Peterborough, PE2 6UP United Kingdom +44 (0) 0330 058 5306 sales@deraat.co.uk www.deraat.co.uk