User Manual for SUPERLIGHTINGLED models including: AHC4, AHC4 LED Signal Amplifier, LED Signal Amplifier, Signal Amplifier, Amplifier
7 hours ago — Signal Amplifier User Manual. Signal amplifier (repealer) receives one way SPI signal, out put signal. Sγmphony 4 control group, multi group Symphony of dream ...
MODEL:AHC4 power SIGNAL IN GND DAT1 DAT2 VCC power SIGNAL IN GND DAT1 DAT2 VCC Signal Amplifier User Manual Signal Amplifier User Manual TTL SIGNAL Specifications: Parameter: Working voltage: DC5V~24V Working temperature: -20-60 Output:4 channels Compatibale IC type: WS2812B,WS2811,SK6812, SK6812RGBW,SM16703,WS2813, WS2815, CS8812, AL2815, WS2801, APA102, SK9822,UCS1903, LPD6803, LPD8806, APA102 Static power consumption: <1W Características: Signal amplifier (repealer) receives one way SPI signal, out put signal Smphony 4 control group, multi group Symphony of dream color striplight changes in effect, and an amplifier used for signal output viaSPI, the theor can be cascaded Countless signal amplifier DC5V~24V wide range of working voltage, but it cannot regulate the output voltage. That means the output voltage of power supply must be the same as the work voltage of your LED lights. The current through the amplifier is limited, when the current consumed is high, you need to add the power supply of the corresponding voltage. 10cm Connection method OUT3 GND DAT1 DAT2 VCC OUT4 GND DAT1 DAT2 VCC POWER VC C POWER AHC4 SIGNAL AMPLIFIER Input Voltage:DC5-24V Output :5V TTL Consumption:<1W GND OUT1 GND DAT1 DAT2 VCC OUT2 GND DAT1 DAT2 VCC Connection method OUT3 GND DAT1 DAT2 VCC OUT4 GND DAT1 DAT2 VCC POWER VC C POWER SIGNAL AMPLIFIER Input Voltage:DC5-24V Output :5V TTL Consumption:<1W GND OUT1 GND DAT1 DAT2 VCC OUT2 GND DAT1 DAT2 VCC SIGNAL IN GND DAT1 DAT2 VCC 4.5cm 7.5CM 2.3CM 1.2CM ELB %0 12V (/% %0 12V EL B %0 12V EL B %0 12V EL B %0 12V EL B %0 12V OUT3 GND DAT1 DAT2 VCC SIGNAL AMPLIFIER Input Voltage:DC5-24V Output :5V TTL Consumption:<1W POWER VC C GND SIGNAL IN GND DAT1 DAT2 VCC OUT2 GND DAT1 DAT2 VCC EL B %0 12V EL B %0 12V OUT4 GND DAT1 DAT2 VCC POWER VC C POWER AHC4 SIGNAL AMPLIFIER Input Voltage:DC5-24V Output :5V TTL Consumption:<1W GND OUT1 GND DAT1 DAT2 VCC OUT2 GND DAT1 DAT2 VCC ELB %0 controller 12V OUT3 GND DAT1 DAT2 VCC EL B %0 12V EL B %0 12V OUT1 GND DAT1 DAT2 VCC OUT4 GND DAT1 DAT2 VCC POWER E LB 7$ $The power Precautions: The controller cannot regulate the output voltage at the VCC. That means the output voltage of your power supply must be the same as the work voltage of your LED lights. If your lights need 5V input, please use a 5V power supply, don't use higher than 5V power supplyThe current through the amplifier is limited, when the consumption current is higher, you need to add power supply of the corresponding voltage additionally. supply EL B %0 12V EL B %0 12VCorel PDF Engine Version 20.0.0.633