AlphaTheta Help Center
Your Ultimate Resource for Millions of User Manuals
Pioneer DJ DM-50D » Online kaufen
Instruction Manual for Pioneer DJ models including: DM-50D, DM-50D-W, DM-50D Active Monitor Speaker, Active Monitor Speaker, Monitor Speaker, Speaker
Pioneer DJ DM-50D User Manual
File Info : application/pdf, 7 Pages, 183.41KB
DocumentDocumentInstruction Manual DM-50D / DM-50D-W Active Monitor Speaker pioneerdj.com/support/ For FAQs and other support information for this product, visit the above site. Downloaded from thelostmanual.org Before you start How to read this manual Thank you for choosing this Pioneer DJ product. Be sure to read this manual, the "Quick Start Guide" and the "Precautions for Use" which are also included with this product. These documents include important information that you should understand before using the speakers. What's in the box · Power cord × 1 · Audio converter cable (3.5 mm stereo mini plug to RCA) × 1 · Speaker cord × 1 · Bottom cushion × 2 (4pcs / 1 sheet) · Quick Start Guide × 1 · Precautions for Use · Warranty (for some regions) * * Only products in Europe. Products in North America and Japan include warranty information in the "Precautions for Use". Part names Front panel 1 2 3 4 5 6 7 8 1 3/4 inch soft dome tweeters 2 POWER indicator Lights up when the power is turned on. The indicator is off in Standby mode. 3 Diffusers Improve the sound directivity of high frequencies and provide spacious sound. 4 LEVEL knob Adjusts the volume. 5 5 inch glass fiber woofers 6 Bass reflex ducts 2 Downloaded from thelostmanual.org 7 Grooves Adjust the airflow of the bass reflex ducts to radiate low frequencies smoothly. 8 Headphone terminal This is a 3.5 mm stereo mini jack type output terminal. Connecting headphones mutes the sound output from the speakers and outputs the sound only from the headphones. Rear panel 1 2 3 4 5 6 7 1 RCA INPUT terminals These are RCA pin type unbalanced input terminals. 2 STEREO MINI INPUT terminal This is a 3.5 mm stereo mini jack type unbalanced input terminal. 3 TRS INPUT terminals These are 1/4-inch phone type balanced input terminals. 4 Speaker connection connectors Connect the left and right speakers using the supplied cord. Do not connect these speakers to an amplifier other than that of this system. Doing so may cause a damage or fire. 5 POWER switch Turns the power for the speakers on and off. 6 AC IN Connect to a power outlet with the supplied power cord. Connect the power cord after all the connections are complete. Use the supplied power cord. 7 SOUND MODE switch Switches between the DJ mode and PRODUCTION mode. DJ mode: For a punchy sound suited for DJ applications. PRODUCTION mode: For flat frequency response that accurately reproduces the input sound. CAUTION The POWER switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation). D3-4-2-2-2a*_A1_En CAUTION · This product is provided with an auto standby function. If a state of no sound continues for a set time (approximately 30 minutes) during use, the product automatically turns off the POWER indicator and enters Standby mode with low power consumption. · When an audio signal is input in Standby mode, the product automatically enters Power-on mode. · This auto standby function cannot be disabled. Downloaded from thelostmanual.org 3 Installation and connections How to install A speaker's playback sound is delicately influenced by conditions in the listening room. To produce optimum listening conditions, take due consideration of the conditions of your installation location before beginning actual installation. · Place the speakers at ear level. · For a natural stereo effect, the right and left speakers should be installed in symmetrical and equidistant positions from the listening position. · The speakers should ideally be placed at an angle of 30° to the left and right (for a total of 60°) from the listening position, and facing inward. 60 ° · To prevent sliding, apply the supplied cushions to the bottom of the speakers. WARNING Store small parts out of the reach of children and infants. If accidentally swallowed, contact a doctor immediately. D41-6-4_A1_En VENTILATION CAUTION When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 15 cm at top, 15 cm at rear, and 15 cm at each side). WARNING Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed. D3-4-2-1-7b*_A1_En Connections · Disconnect the power cord before making or changing connections. · Read the instruction manuals for the devices you are going to connect with the speakers. · Connect the power cord after all the connections are complete. · Use the supplied power cord. · The input signals to the RCA, STEREO MINI and TRS input terminals are mixed, so please beware of the volume level. Connecting cords Connect the supplied speaker cord to the speakers. 1 Strip about 1 cm of the head of the supplied speaker cord and twist and remove the exposed insulator. After removing the insulator, thoroughly twist the core wires. Red + Black - The cord with the red line 2 Connect the supplied speaker cord to the speaker terminals on the LEFT and RIGHT sides. 3 Insert the core wires into the terminals while pressing the claw on the speaker terminal. Connect the speaker cord with the red line into the + terminal side (red) and the speaker cord without the red line into the terminal side (black). 4 Downloaded from thelostmanual.org CAUTION · After connecting to the terminals, lightly pull the speaker cord to make sure that heads of the speaker cord are securely connected to the terminals. A loose connection might cause audio output to be interrupted or noise to be output. · When connecting the speaker cord, thoroughly twist the core wires, and make sure that the core wires are not protruding out of the speaker terminals. Core wires protruding out of the speaker terminals may come into contact with the rear panel or with each other. This may cause an excessive load to be placed on the amplifier which results in operation stopping or a malfunction. · If a mistake is made with the polarities (+, -) on the LEFT and RIGHT sides when connecting the LEFT and RIGHT speaker cord, normal stereo effect can no longer be obtained. Additional information Troubleshooting If you think something is wrong with the speakers, check the information below and refer to the [FAQ] for the DM-50D at the URL below. pioneerdj.com/support/ · Inspect devices connected with the speakers. · The speakers may restore proper operation after you turn it off and on. If the problems continue, read the "Precautions for Use" and consult an authorized service company or your dealer. Problem The power is not turned on. Check Is the power cord properly connected? Measures Plug in the power cord to an AC outlet. No sound is output or the sound is low. Is the connected device set properly? Set the devices external input and volume properly. Are the connection cables properly connected? Connect the connection cables properly. Are the terminals and plugs dirty? Clean the terminals and plugs before making connections. Is the volume set to the proper position? Is the power turned on? Turn the [LEVEL] knob on the front panel of the speaker clockwise to increase the volume. Turn on the [POWER] switch on the rear panel of the speaker. The POWER indicator (white) does not light. Is the power turned on? Turn on the [POWER] switch on the rear panel of the speaker. Are the speakers in Standby mode? The speakers wouldn't recover (power-on) from Standby mode. The sound is affected by distortion. Is the input signal level low? Is the volume set to the proper position? Unwanted noise is heard. (It continues sounding loud.) The sound is only output from the left speaker. The sound is only output from one speaker. Is the input level from the connected device appropriate? Is the volume set to the proper position? Is the speaker cord connected properly? Is the device connected properly? Turn off the [POWER] switch on the rear panel of the speaker and then turn it back on after a few seconds. Increase the input signal level. Turn the [LEVEL] knob on the front panel of the speaker counterclockwise to reduce the volume. Adjust the output level of the connected device properly. Turn the [LEVEL] knob on the front panel of the speaker counterclockwise to reduce the volume. Connect the left and right speakers properly. Connect the device to both the left and right input terminals. The power turns off (Standby mode) automatically. Did a state of no sound continue for approximately 30 Input signals from the RCA, TRS or stereo mini plug input terminal. minutes or longer? Is the input signal level low? Increase the input signal level. The sound is interrupted or unwanted noise Is there a contact problem with the connection can be heard. cables? Reconnect the connection cables. Trademarks and registered trademarks · Product, technology and company names, etc. mentioned herein are trademarks or registered trademarks of their respective owners. Downloaded from thelostmanual.org 5 Specifications Type............................................................................................................................................................... 2-Way Active Speaker Amplifier Amplifier type ........................................................................................................................................................ Class D with DSP Amplifier output.............................................................................................................................. Lch: 25 W / 4 , Rch: 25 W / 4 Input terminals (balanced input)........................................................................................................................... 1/4 TRS jacks × 1 Input terminals (unbalanced input)........................................................................... RCA pin jacks × 1, 3.5 mm stereo mini jack × 1 Input impedance ......................................................................................................................................................................10 k Output terminal ...................................................................................................................................... 3.5 mm stereo mini jack × 1 Speaker Enclosure.........................................................................................................................................................................Bass reflex Enclosure material .............................................................................................................................................. MDF vinyl laminate Woofer (LF driver)............................................................................................................................................... 5 (127 mm) cones Tweeter (HF driver) ...................................................................................................................................... 3/4 (19 mm) soft dome Power unit / other Supported voltages ........................................................................................................................ AC 110 V 240 V, 50 Hz / 60 Hz Power consumption .................................................................................................................................................................. 25 W Power consumption during standby mode ....................................................................................................................0.3 W or less Max. dimensions ........................(W × H × D) Lch: 175 × 262 × 257 mm / 6.89 × 10.32 × 10.12, Rch: 175 × 262 × 247 mm / 6.89 × 10.32 × 9.72 Weight..............................................................................................................................Lch: 3.9 kg / 8.6 lbs., Rch: 3.5 kg / 7.7 lbs. The specifications and design of this product are subject to change without notice. 6 Downloaded from thelostmanual.org © 2021 AlphaTheta Corporation. All rights reserved. 6F, Yokohama i-Mark Place, 4-4-5 Minatomirai, Nishi-ku, Yokohama, Kanagawa 220-0012 JAPAN 6F, i-Mark Place, 4-4-5 , -, , 220-0012 Artemis Building, Odyssey Business Park, West End Road, South Ruislip, Middlesex, HA4 6QE, U.K. TEL: +44-203-7617-220 2050 W. 190th Street, Suite 109, Torrance, CA 90504, U.S.A. TEL: +1 (424) 488-0480 Downloaded from thelostmanual.org AT_001_all_01 <DRI1722-A>