Everwell MGTC-20 Series

Let's get start!

Operation guideline. Please take below simple guideline instruction as reference.

Note: If you registered the account and added device before, when you re-install the APP again and login, the added device will remain .

FCC Caution (FCC ID: 2AJCLTWAC-TYWFS)

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The distance between user and device should be no less than 20cm.

Wi-Fi Module specification and basic information

1. Minimum specifications on a Smart phone:

• Android 5.0 version or higher
• IOS 9.0 version or higher

2. Basic parameters for Wi-Fi module

3. Wi-Fi module location and appearance in indoor unit

Open the front panel, the Wi-Fi module is nearby the electric box cover or on the panel.

[Diagram: Wi-Fi module with labels RESET button, SN, Connecting cable]

Download and Install the App

[Smart Life App Icon]

For Android smart phone

Method1: Please scan the QR code with a browser scanner, download and install the APP.

Method2: Open the Google "Play Store" on your smart phone and search "Smart Life", download and install the APP.

[Google Play Store Icon]

For IOS smart phone

Method1: Please scan the QR code and follow the tips to get into "AppStore", download and install the APP.

Method2: Open the Apple "AppStore" on your smart phone and search "Smart Life", download and install the APP.

[App Store Icon]

Note: Please enable the permissions of Storage/Location/Camera for this APP when installing. Otherwise it will have some problems when operating.

Activate APP

The first time the app is used, it will need activating.

1. Launch the APP "Smart Life" on your smart phone.

[Smart Life App Icon]

2. Method1: Tap button "Scan" and scan the right Activate QR code

Method2: Tap "or Enter Activation Code" in bottom of the screen, then enter the activate code and tap "CONFIRM".

[Diagram: App screen showing 'Scan the activation QR code from instructions or device' with a 'Scan' button]

[Diagram: QR code labeled 'Activate QR code and activation code' with text 'OR DAIZUKI']

Note: Without the QR code or activation code, you can't active the APP and using it, please keep them safe.

[Diagram: Input field for activation code with 'CANCEL' and 'CONFIRM' buttons]

Registration

1. If you don't have any account please tap button "Register".

2. Read the Privacy Policy and tap "Agree".

[Diagram: 'Register' button and 'Log in with existing account' option]

Privacy Policy: We pay high attention to the privacy of personal information. To fully present how we collect and use your personal information, we revised the Privacy Policy in detail in compliance with the latest laws and regulations. By clicking Agree, you agree that you have fully read, understood and accepted all the content of the revised Privacy policy. Please take your time to read the Privacy Policy. If you have any question, please contact us at any time.

[Buttons: 'Disagree', 'Agree']

3. Tap ">" and choose the country.

4. Enter your phone number or e-mail address.

5. Tap the button "Obtain verification code".

[Diagram: Screen showing 'Resister', country selection 'China +86', phone number input '138********', and 'Obtain verification code' button. Also shows 'I agree with Service Agreement and Policy']

[Diagram: Country selection list with search bar, showing 'Afghanistan', 'Albania', 'Algeria', etc.]

Registration

6. Enter the verification code you received from phone message or e-mail.

7. Set the Password with 6-20 characters including characters and numbers.

8. Tap "Done".

[Diagram: Screen showing 'Enter verification code' with asterisks for input and 'Verification code is sent to your phone: 86-***********, Resend(55s)']

[Diagram: Screen showing 'Set Password' with asterisks for input and '6-20 characters for password, including character, numbers']

Login

1. Tap "Log in with existing account".

2. Enter your registered account and password.

3. Tap "Log in" button.

[Diagram: Login screen with 'Register' and 'Log in with existing account' options]

[Diagram: Login screen showing country selection '+86', account input '138********', password input, and 'Log in' button. Also shows 'SMS verify and sign in', 'Forgot password', and 'I agree with Service Agreement and Policy']

Login

The first time the APP is used, Create family is needed:

4. Tap "Create family".

5. Make name for the family.

6. Set the location.

7. Choose default rooms or add new rooms.

8. Tap "Done" and "Completed".

[Diagram: 'Turn on your smart life' screen with 'Create family' button and 'Log out' option]

[Diagram: 'Add family' screen showing 'Family Name', 'My home', 'Set location', and 'Smart devices in rooms' list with options like 'Living Room', 'Master Bedroom', etc.]

[Diagram: 'Add Room' screen showing 'Room Name' and a list of rooms like 'Living Room', 'Master Bedroom', etc.]

[Diagram: Pop-up asking 'Allow Smart Life to access this device's location?' with options 'ALLOW ONLY WHILE IN USE', 'ALLOW ALL THE TIME', 'DENY']

[Diagram: 'Family created successfully' confirmation with 'View family' and 'Completed' buttons]

Note: The app can open the map on your phone and you can set the location where you are.

Login

Forgot the password

If you forgot the password, you can login as below: (Only for phone number accounts)

1. Tap "SMS verify and sign in".

2. Enter your phone number and tap button "Obtain verification code".

3. Enter the verification code received by your phone.

[Diagram: Login screen with 'SMS verify and sign in' option selected, showing country '+86', phone number input '138********', and 'Obtain verification code' button]

[Diagram: Screen showing 'Enter verification code' with asterisks and 'Verification code is sent to your phone: 86-***********, Resend(55s)']

Or you can reset the password as below:

1. Tap "Forgot password".

2. Enter your account (phone number or e-mail address) and tap button "Obtain verification code".

3. Enter the verification code received by your phone or e-mail.

4. Set the new password and tap button "Done".

[Diagram: Forgot password screen showing country '+86', account input '138********', and 'Obtain verification code' button]

[Diagram: Screen showing 'Enter verification code' with asterisks and 'Verification code is sent to your phone: 86-***********, Resend(55s)']

[Diagram: Screen showing 'Set Password' with asterisks and '6-20 characters for password, including character, numbers']

Add device

There are 2 modes CF(Quick connection) and AP(Access Point) for adding device.

CF mode

1. Power on the indoor unit, no need to launch the air conditioner.

2. Click "+" in the upper right corner of the "Home" screen or tap "Add device" on the room which has no device.

3. Tap the "Split Air conditioner" logo.

4. Reset the Wi-Fi module by pressing the "DISPLAY" on the remote controller 6 times, or use a suitable tool to press the reset button on the Wi-Fi module, until it shows "CF" on the indoor display, then tap "Next Step".

5. Input the password of the Wi-Fi which the same as your smart phone connected, tap "Confirm" (You can change network if needed).

6. You can see the percent rate of connecting process, at the same time "PP", "SA", "AP" shining in turn on the indoor display.

• "PP" means "Searching the router"
• "SA" means "connected to the router"
• "AP" means "connected to the server"

[Diagram: Home screen showing 'my home', '+', 'All Devices', 'Living Room', 'Master Bedroom', 'No device', 'Add Device' button, and navigation icons 'Home', 'Me'.]

[Diagram: 'Add Device' screen with options 'Add Manually', 'Search Device', and icons for 'Large Home Ap...', 'Security & Sensors', 'Window Type Air Conditioner', 'Split Air Conditioner', 'Portable Air cond...', 'Fresh air purifier', 'Dehumidifier'.]

[Diagram: 'Add Device AP Mode' screen showing 'Press the DISPLAY on the remote control key 6 times in the time of 6 seconds until the LCD screen show "CF"', 'View help', and 'Next Step' button.]

[Diagram: 'Enter Wi-Fi password' screen showing Wi-Fi channel information, 'wifiname', password input field, 'Change network' button, and 'Confirm' button.]

[Diagram: 'Add Device' screen showing 'Connecting now' with a 50% progress circle, and status indicators 'Searching for device', 'Registering device to the cloud', 'Initializing your device'.]

[Diagram: 'Add Device' screen showing 'Device added successfully' with 'Sample1', room assignments, 'Rename the device', 'Select the location room', and 'Done' button.]

Add device

AP mode

1. Power on the indoor unit, no need to launch the air conditioner.

2. Click "+" in the upper right corner of the "Home" screen or tap "Add device" on the room which has no device.

3. Tap the "Split Air conditioner" logo.

4. Reset the Wi-Fi module by pressing the "DISPLAY" on the remote controller 6 times, or use a suitable tool to press the reset button on the Wi-Fi module, until it shows "AP" on the indoor display, then tap "Next Step".

5. Input the password of the Wi-Fi which the same as your smart phone connected, tap "Confirm".

6. In the network setting screen, select "SmartLife-****", and tap "<".

7. You can see the percent rate of connecting process, at the same time "PP", "SA", "AP" shining in turn on the indoor display.

• "PP" means "Searching the router"
• "SA" means "connected to the router"
• "AP" means "connected to the server"

[Diagram: Home screen showing 'my home', '+', 'All Devices', 'Living Room', 'Master Bedroom', 'No device', 'Add Device' button, and navigation icons 'Home', 'Me'.]

[Diagram: 'Add Device AP Mode' screen showing 'Press the DISPLAY on the remote control key 6 times in the time of 6 seconds until the LCD screen show "AP"', 'View help', and 'Next Step' button.]

[Diagram: 'Enter Wi-Fi password' screen showing Wi-Fi channel information, 'wifiname', password input field, 'Change network' button, and 'Confirm' button.]

[Diagram: 'AP mode' screen showing 'AVAILABLE NETWORKS' with 'WIFI1', 'SmartLife-****', 'office wifi'.]

[Diagram: 'Add Device' screen showing 'Connecting now' with a 50% progress circle, and status indicators 'Searching for device', 'Registering device to the cloud', 'Initializing your device'.]

[Diagram: 'Add Device' screen showing 'Device added successfully' with 'Sample2', room assignments, 'Rename the device', 'Select the location room', and 'Done' button.]

Air conditioner control

The device control screen will pop up automatically after adding the device. The device control screen will pop up manually by tapping the device name on the home screen.

[Diagram: Home screen showing 'my home', '+', 'All Devices', 'Living Room', 'Master Bedroom', 'Sample1 Turned off', 'Sample2 Already On', and navigation icons 'Home', 'Me'.]

Note: There are two different control forms based on different software or Wi-Fi module firmware. Please read the manual carefully based on the real control interface.

Control form1

[Diagram: Control form 1 interface showing 'Sample2', temperature display '23°C Set Temperature', and control buttons '-', '+', 'Mode', 'Fan', 'Function', 'Timer'.]

Control form2

[Diagram: Control form 2 interface showing 'Sample1', current mode 'Cool', temperature display '25°C', and function buttons 'ON/OFF', 'Mode', 'Fan Speed', 'Precision Air Flow', 'Eco', 'Sleep', 'Timer', 'More'.]

Air conditioner control

Control form1

The main control interface

[Diagram: Control form 1 interface with labels pointing to: 'Back to the Home screen', 'Sample2', 'Indicator of setting temperature', 'Decrease the setting temperature', '23°C Set Temperature', 'Selected Mode/Fan speed/Functions indicator', 'Increase the setting temperature', and navigation buttons 'Mode', 'Fan', 'Function', 'Timer'.]

Air conditioner control

Control form1-Mode setting

1. Tap Mode to pop up the Mode screen.

2. Select one of the mode Feel/Cool/Heat/Dry/Fan.

3. Tap anywhere around the setting temperature to cancel the Mode setting.

[Diagram: Control form 1 interface showing 'Sample2', '23°C Set Temperature', and a 'Mode' selection screen with options 'Feel', 'Cool', 'Heat', 'Dry', 'Fan'.]

Control form1-Select fan speed

1. Tap Fan to pop up the Fan screen.

2. Select one of the fan speed High/med/Low/Auto.

3. Tap anywhere around the setting temperature to cancel the selection.

[Diagram: Control form 1 interface showing 'Sample2', '23°C Set Temperature', and a 'Fan' selection screen with options 'High', 'Med', 'Low', 'Auto'.]

Air conditioner control

Control form1-Function setting

1. Tap Function to pop up the Function screen.

2. Select one of the functions Sleep/Turbo/ECO.

3. Select UP-DOWN/LEFT-RIGHT for auto swing with direction of UP-DOWN/LEFT-RIGHT.

4. Tap anywhere around the setting temperature to cancel the Function setting.

[Diagram: Control form 1 interface showing 'Sample2', '23°C Set Temperature', and a 'Function' selection screen with options 'Sleep', 'Turbo', 'ECO', and directional arrows for auto swing.]

Control form1-Timer adding

1. Tap Timer to pop up the Add Timer screen.

2. Tap Add Timer.

[Diagram: Control form 1 interface showing 'Sample2', '23°C Set Temperature', and a 'Timer' button.]

[Diagram: 'Add Timer' screen with an 'Add timer' button.]

Air conditioner control

Control form1-Timer adding

3. Select the time, select the repeat days and Timer on/off.

4. Select the Mode/Fan speed/Function and select the setting temperature for Timer on.

5. Tap Save to add the timer.

[Diagram: 'Timer on' screen showing hour/minute selection, day selection (Mon-Sun), Timer On/Off settings, Mode, Fan Speed, Temperature, and Function settings. Includes 'Cancel', 'Add Timer', 'Save' buttons.]

[Diagram: 'Timer off' screen showing similar settings for timer off. Includes 'Cancel', 'Add Timer', 'Save' buttons.]

Control form1-Timer Management

1. Tap the bar of timer to edit the Timer like the Timer adding process.

2. Click the switch to enable or disable the Timer.

3. Hold the bar of Timer about 3 seconds and pop up the Remove Timer screen, tap CONFIRM and remove the Timer.

[Diagram: 'Add Timer' screen showing a timer entry '12:20 Once Timer:Off' and '12:20 Mon, Tue, Wed, Thurs Timer: On 16°C Cool Turbo UP-DOWN'. Includes 'Add timer' button.]

[Diagram: 'Remove Timer' pop-up with 'Remove the timer?' text and 'CANCEL CONFIRM' buttons.]

Air conditioner control

Control form2

The main control interface

[Diagram: Control form 2 interface showing 'Sample1', current mode 'Cool', temperature display '25°C', and function buttons 'ON/OFF', 'Mode', 'Fan Speed', 'Precision Air Flow', 'Eco', 'Sleep', 'Timer', 'More'. Labels point to 'Back to the Home screen', 'Decrease the setting temperature', 'Selected Functions indicator', 'Power on/off', 'Tips', 'Name of the device', 'Current mode', 'Increase the setting temperature', 'Different background for different mode: Cool/Heat/Dry/Fan/Auto', and 'Function Buttons'.]

Air conditioner control

Control form2-Mode setting

1. Tap the Mode button.

2. There are 5 modes on the Mode screen, tap one button to set the Air conditioner working mode.

3. Tap the X button to back the main control screen.

4. The mode and background will change on the screen.

[Diagram: Control form 2 interface showing 'Sample1', 'Cool 25°C'. A 'Mode' selection screen is shown with options 'Cool', 'Heat', 'Dry', 'Fan', 'Auto'.]

Note: Please read the details of each mode in the user manual to control more comfortable.

Control form2-Fan speed selection

1. Tap the Fan speed button.

2. Choose your desired fan speed and tap it.

3. Tap the X button to back the main control screen.

4. The selected fan speed indicator will appear on the screen.

[Diagram: Control form 2 interface showing 'Sample1', 'Cool 25°C'. A 'Fan Speed' selection screen is shown with options 'Turbo', 'high', 'Mid-High', 'Mid', 'Mid-Low', 'Low', 'Mute', 'Auto'.]

[Table: Mode vs Fan Speed compatibility: Cool (All speeds), Fan (All speeds), Dry (Cannot be adjusted), Heat (All speeds), Auto (All speeds)]

Note: Fan Speed can't be adjusted on Dry mode.

Note: Fan Speed screen may appear slightly different, depending on the air conditioner model. Example as below:

[Diagram: Alternative Fan Speed selection screen with options 'high', 'Mid', 'Low', 'Auto'.]

Air conditioner control

Control form2-Air Flow control

1. Tap the Precision Air Flow button or Swing Flow button.

2. Choose your desired air flow and tap it.

3. Tap the X button to back to the main control screen.

4. The selected air flow indicator will appear on the screen.

Note: For some models without auto Left-Right wind, If you activate it, you will hear a beep, but no any actions.

[Diagram: Control form 2 interface showing 'Sample1', 'Cool 25°C'. A 'Precision Air Flow' screen is shown with options for 'Up-Down Flow Control' and 'Left-Right Flow Control', including 'Up-Down Swing', 'Upwards Swing', 'Downwards Swing', 'Top Fix', 'Upper Fix', 'Middle Fix', 'Lower Fix', 'Bottom Fix'.]

[Diagram: Another view of 'Precision Air Flow' options including 'Left-Right Swing', 'Left Swing', 'Middle Swing', 'Right Swing', 'Center-Left Swing', 'Center-Right Swing', 'Wide Swing', 'Left fix', 'Center-Left Fix', 'Middle Fix', 'Center-Right Fix', 'Right Fix', 'Whole Anger Fix', 'Left Wide Angle Fix', 'Right Wide Angle Fix'.]

Note: The Main control screen and Air Flow screen may appear slightly different, depending on the air conditioner model. Example as below:

[Diagram: Control form 2 interface showing 'Sample1', 'Cool 25°C'. A 'Swing Flow' screen is shown with options 'Up-Down' and 'Left-Right'.]

Air conditioner control

Control form2-ECO function

1. For Eco function, just tap the button to activate the function, the button will be lighting and the indicator will appear on the screen.

2. Tap again to disable the function.

3. Temperature controlled for some air conditioner model:

• In Cooling mode, the new setting temperature will ≥ 26℃.
• In heating mode, the new setting temperature will ≤ 25℃.

[Diagram: Control form 2 interface showing 'Sample1', 'Heat 25°C' and 'Cool 26°C' with the 'Eco' button highlighted.]

[Table: ECO enabled status for modes: Cool (Yes), Fan (No), Dry (No), Heat (Yes), Auto (Yes)]

ECO is disabled on Fan/ Dry/Auto mode.

Note: The Main control screen and ECO control method may appear slightly different, depending on the air conditioner model. Example as below:

[Diagram: Control form 2 interface showing 'Sample1', 'Cool 23°C' with 'Low' and 'ECO' indicators.]

Note: ECO is disabled on Turbo/Sleep mode too for some air conditioner model.

Air conditioner control

Control form2-Sleep function

1. Tap the Sleep button.

2. Choose your desired sleep mode and tap it.

3. Tap the X button to back to the main control screen.

4. The selected sleep mode indicator will appear on the screen.

[Diagram: Control form 2 interface showing 'Sample1', 'Heat 25°C'. A 'Sleep' selection screen is shown with options 'Standard', 'The aged', 'Child'.]

[Table: Sleep enabled status for modes: Cool (Yes), Fan (No), Dry (No), Heat (Yes), Auto (Yes)]

Sleep is disabled on Fan/ Dry/Auto mode.

Note: The Main control screen may appear slightly different, depending on the air conditioner model. Example as below:

[Diagram: Control form 2 interface showing 'Sample1', 'Cool 23°C' with 'Low' and 'Sleep' indicators.]

Note: Sleep is disabled on Turbo/Sleep mode too for some air conditioner model.

Air conditioner control

Control form2-Timer(on) setting

1. Tap the Timer button.

2. Tap + in the upper right corner of the Timer main screen.

3. Choose the Time/Repeat/Switch OFF then tap Save.

4. The timer(off) will appear on the Timer main screen.

[Diagram: Control form 2 interface showing 'Sample1', 'Cool 25°C', and a 'Timer' button.]

[Diagram: 'Timer' screen showing 'No Timer' and a '+' button.]

[Diagram: 'Timer' screen showing time selection (e.g., '21 : 29'), 'Repeat' selection ('Monday....>'), and 'Switch' selection ('OFF>'). Includes 'Save' button.]

Tap repeat > then tap your desired repeat days or Once, then tap Confirm your selection.

[Diagram: Repeat day selection screen showing 'Monday', 'Tuesday', 'Wednesday', etc., with checkmarks. Includes 'Cancel', 'Repeat', 'Confirm' buttons.]

Tap Switch > then slide the screen to choose ON and Confirm.

[Diagram: Switch selection screen showing 'ON' and 'OFF' options. Includes 'Cancel', 'Switch', 'Confirm' buttons.]

[Diagram: Timer screen showing '21:29 OFF, Weekday'.]

Air conditioner control

Control form2-Timer(off) setting

1. Tap the Timer button.

2. Tap + in the upper right corner of the Timer main screen.

3. Set the Time/Repeat Date/Switch(ON)/Temperature/Mode/ Fan speed/Air Flow as your desired and then tap Save.

4. The timer will appear on the Timer main screen.

[Diagram: Control form 2 interface showing 'Sample1', 'Cool 25°C', and a 'Timer' button.]

[Diagram: Timer screen showing existing timers '21:29 OFF, Weekday' and '04:30 OFF'.]

[Diagram: Timer screen showing time selection (e.g., '16 : 19'), 'Repeat' selection ('Monday....>'), 'Switch' selection ('ON>'), 'Temperature' ('25°C>'), 'Mode' ('Cool>'), 'Fan Speed' ('Mid>'), 'Precision Air Flow' ('Up-Down Swing>'). Includes 'Save' button.]

Tap repeat > then tap your desired repeat days or Once, then tap Confirm your selection.

[Diagram: Repeat day selection screen showing 'Monday', 'Tuesday', 'Wednesday', etc., with checkmarks. Includes 'Cancel', 'Repeat', 'Confirm' buttons.]

Tap Switch > then slide the screen to choose ON and Confirm.

[Diagram: Switch selection screen showing 'ON' and 'OFF' options. Includes 'Cancel', 'Switch', 'Confirm' buttons.]

[Diagram: Timer screen showing '21:29 OFF, Weekday', '04:30 OFF', and '16:19 ON, Cool, Mid, Up-Down Swing 25°C, M...'.]

Tap Temperature/Mode/Fan Speed/ Air Flow > one by one then set as your desired as mentioned on the previous chapter and tap Confirm the setting.

Air conditioner control

Control form2-Timer management

1. Change the Timer setting: Tap anywhere of the timer list bar except the switch bar to get into the Timer setting screen, change the setting and then tap save.

2. Enable or Disable the Timer: Tap the left of the switch to disable the Timer. Tap the right of the switch to enable the Timer.

3. Delete the Timer: Slide the list bar of the Timer from right to left until Delete button appear, then tap delete.

[Diagram: Timer screen showing existing timers and switch toggles. Includes instructions 'Slid left to disable the Timer.' and 'Slid right to enable the Timer.']

[Diagram: Timer screen showing a timer entry with a 'Delete' button appearing after sliding.]

Air conditioner control

Control form2-More functions

1. Tap the More button to operate additional functions if it appears on the screen.

[Diagram: Control form 2 interface showing 'Sample1', 'Cool 25°C'. A 'More' screen is shown with icons for 'Display', 'Buzzer', 'Anti-Mildew', 'GEN Mode', 'Health', 'Reservation', 'Electricity Management', 'Electricity Monitoring', 'Self-diagnosis'.]

Note: Some air conditioner models don't have the more button.

Note: The appearance maybe different, some icons will be hidden if the air conditioner does not have this function or do not enable on the current mode.

2. Tap the "Display" to switch on/off the indoor LED display.

[Icon: Display]

3. Tap the "Buzzer" to switch on/off the buzzing when operating through Wi-Fi APP.

[Icon: Buzzer]

4. Tap the "Anti-Mildew" button to activate the Anti-Mildew function, if it is available on the screen. After AC turning off, it will start drying, reduce residual moisture and prevent mould, after function finish, it will automatically turn off.

[Icon: Anti-Mildew]

5. Tap the "Health" button to switch on/off the healthy function, if it is available on the screen. It activates the antibacterial ioniser function. This function only for models with the ioniser generator.

[Icon: Health]

Air conditioner control

Control form2-More functions

6. Tap the "GEN Mode" button, if it is available on the screen. In this Mode, you can choose one of the three levels of current. The air conditioner will maintain proper current to save energy.

[Diagram: 'GEN Mode' screen showing levels '30%', '50%', '80%' labeled LV1, LV2, LV3.]

7. Tap the "Electricity Monitoring" button if it is available on the screen. In this function, you can monitor the air conditioner electricity consumption.

[Diagram: 'Electricity monitoring' screen showing daily and monthly consumption graphs, with total electricity and running time statistics.]

You can tap this button to pop up the calendar then select the date.

8. Tap the "Self-Cleaning" button, if it is available on the screen. Check the details of the Self-Cleaning function on User Manual.

[Icon: Self-Cleaning]

9. Tap the "8°C Heat" button, if it is available on the screen. This function helps keep the room temperature over 8°C. Check the details of the 8°C Heat function on User Manual.

[Icon: 8°C Heat]

Air conditioner control

Control form2-More functions

10. Tap the "Reservation" button, if it is available on the screen. You can set the time, repeat day, temperature, mode, fan speed, air flow as you desired and then tap Save to activate the function. The air conditioner will automatically reach your settings at the appointment time.

[Diagram: 'Reservation' screen showing time selection, repeat setting, temperature, mode, fan speed, and precision air flow settings. Includes 'Save' button.]

[Diagram: 'Reservation' screen showing a set reservation time '16:19:00' with details and confirmation text.]

11. Tap the "Self-diagnosis" button, if it is available on the screen. The air conditioner will automatically diagnosis itself and indicate the Error code and the problem instructions if possible.

[Diagram: 'Self-diagnosis' screen showing '48% Checking' with 'Cancel' button.]

[Diagram: 'Self-diagnosis' screen showing '100% Complete' with 'Error code: E0 Indoor and outdoor communication failure' and 'OK' button.]

Air conditioner control

Control form2-More functions

12. Tap the "Electricity Management" button if it is available on the screen.

[Table: Electricity Management modes (Default mode, Fixed Electricity, Fixed Temp) and their actions.]

[Diagram: Screens showing 'Default mode' with electricity percentage and temperature curves.]

[Diagram: Screens showing 'Fixed Electricity' with power consumption options and temperature curves.]

[Diagram: Screens showing 'Fixed Temp' with temperature selection and temperature curves.]

[Diagram: Control form 2 interface showing 'Sample1', 'Cool 25°C', and an 'Electricity Management indicator'.]

Device details and management

Tap on control form1 or tap ... on control form2, get into the device details screen. Here you can get some useful information and sharing the device to other accounts. Check the following pictures and instructions carefully.

[Diagram: Control form 1 interface showing 'Sample2', temperature, and control buttons.]

[Diagram: Control form 2 interface showing 'Sample1', temperature, and function buttons.]

Tap to change the device location to another room

Feed back the problems or some suggestions to the APP administrator.

[Diagram: 'Details of device' screen showing 'Information' (Modify Device Name, Device Location, Check Device Network, Supported Third-part Control) and 'Others' (Device Sharing, Device Info, Feedback, Check for Firmware Update, Remove Device). Labels point to specific actions like checking network status, connecting voice controllers, sharing, etc.]

Device details and management

How to share the devices to other accounts?

1. Tap "Device Sharing" and pop up Device Sharing screen.

2. Tap "Add Sharing".

3. Select the region and enter the account which you want to sharing.

4. Tap "Completed", the account will appear on your sharing list.

5. The received sharing members should hold pressing the home screen and slide down to refresh the device list, the device will appear on the device list.

[Diagram: 'Details of device' screen showing 'Device Sharing' option.]

[Diagram: 'Details of device' screen showing 'Sharing List' with 'Alias name1'. Includes 'Adding sharing' button.]

[Diagram: 'Add Sharing' screen showing 'Region' and 'Account number' input fields. Includes 'Completed' button.]

[Diagram: Home screen showing 'my home', 'All Devices', 'Living Room', 'Master Bedroom', 'Sample1 Turned off', 'Sample2 Already On'. Includes instructions 'Hold on and slide down to refresh the device list'.]

Hold the bar about 3s then you can delete the sharing account.

Account management

Account Profile setting

[Diagram: Home screen showing 'my home', 'All Devices', 'Living Room', 'Master Bedroom', 'Sample1 Turned off', 'Sample2 Already On'.]

[Diagram: 'Profile' screen showing 'Nick name Account******', 'Home Management', 'Message Center', 'Help Center', 'More Services', 'Settings'.]

Change the nick name of your account

[Diagram: 'Profile' screen showing 'Edit name' input field for 'Account one', with 'Cancel' and 'Save' buttons.]

[Diagram: 'Profile' screen showing 'Profile Picture', 'Nickname', and 'Account Security' options.]

Select a picture for the account from local album

Select the time zone

[Diagram: 'Account Security' screen showing 'Phone Number', 'Location', 'Change Login Password', 'Pattern Unlock', 'Change Pattern Password', 'Deactivate Account'.]

Set a pattern password for launching the APP

Change the password like reset password on page7

Tap the switch to enable or disable the Pattern password

Please carefully to deactivate the account for all data will be deleted.

Account management

Home(Family) management

1. Tap the name of home at the left upper corner of the Home Screen and select the Home Management. Or tap Me and tap Home Management.

2. Tap one of the families in the family list and get into Family Settings screen.

[Diagram: Home screen showing 'My Home', 'All Devices', 'Living Room', 'Master Bedroom', 'Sample1 Turned off', 'Sample2 Already On'.]

[Diagram: 'My Home' dropdown menu showing 'My Home', 'My Office', 'Home Management'.]

[Diagram: 'Home Management' screen showing 'My Home', 'My Office', 'Add family'.]

[Diagram: 'Profile' screen showing 'Nick name', 'Home Management', etc.]

Note: Tap "Add family" and refer to page 6 to add a new family.

3. Set the family as the following indicators.

Open the map automatically then you can set the location

Add other account into this family to control the device

[Diagram: 'Family settings' screen showing 'Family Name', 'Room Management', 'Family Location', 'Family members' (Nick name, Account******). Includes 'Add Member' and 'Remove Family' buttons.]

Tap to rename the family name

Tap to get into Room Management

Tap to set a name and select picture for the family member

Remove the Family from your account

Notice

1. For technical update, there is maybe deviation of the actual items from what is on the manual. We express our apologies. Please refer to your actual product and APP.
2. Smart air conditioner APP can be altered without notice for quality improvement and also be deleted depending on the circumstances of manufacturing firms .
3. In case Wi-Fi signal strength is weakened, smart App may be disconnected. So make sure the indoor unit near to wireless router.
4. DHCP server function should be activated for wireless router.
5. The internet connection may fail because of a firewall problem. In this case, contact your internet service provider.
6. For smart phone system security and network setting, make sure Smart air conditioner APP is trusted.

Trouble Shooting