internet.to
Installation Guide for D-Link models including: R3, 2AR6U-R3, 2AR6UR3, R3 AX3000 MU-MIMO WiFi Gigabit Router, AX3000 MU-MIMO WiFi Gigabit Router, MU-MIMO WiFi Gigabit Router, WiFi Gigabit Router, Gigabit Router, Router
Netduma Limited R3 Wireless Router 2AR6U-R3 2AR6UR3 r3
R3 Wireless Router by Netduma
File Info : application/pdf, 6 Pages, 1.11MB
DocumentDocumentR3 AX3000 MU-MIMO Wi-Fi Gigabit Router BEFORE YOU BEGIN Delivery Package · Router R3 · 12V/1.5A · Ethernet cable · "Quick Installation Guide" (brochure). If any of the items are missing, please contact your reseller. The "User Manual" and "Quick Installation Guide" documents are available on D-Link website. ! Default Settings IP address of router: Username (login): Password: Name of wireless network (SSID): Wireless Password: 192.168.0.1 admin (as printed on the device label) R3-2.4G-XXXX R3-5G-XXXX (as printed on the device label) ! The router R3 with default settings cannot connect to the Internet.To get started, please set your own password for access to the web-based interface and change the WLAN name (SSID); then, if SYSTEM REQUIREMENTS AND EQUIPMENT · A computer with any operating system that supports a web browser. · A web browser to access the web-based interface of the router: Apple Safari 8 and later, Google Chrome 48 and later, Microsoft Internet Explorer 10 and later, Microsoft Edge 20.10240 and later, Mozilla Firefox 44 and later, Opera 35 and later. · A NIC (Ethernet or Wi-Fi adapter) to connect to the router. · An 802.11a, b, g, n, or ac Wi-Fi adapter to connect to a wireless network. SAFETY RULES AND CONDITIONS Make sure that the power adapter and cables are not damaged. The device should be used only as intended in accordance with the documents. in the areas with high humidity. Do not place foreign objects on the device. Do not the device and the temperature inside the device's cover should be within the range Only use the power adapter supplied with the device. Do not plug in the adapter, if its case or cable are damaged. Plug the adapter only into working electrical outlets with parameters indicated on the adapter. Use a damp cloth to clean the device. Do not use liquid/aerosol cleaners or magnetpoweradapter. CONNECTION AND CONFIGURATION 1. Connect the power cord to the power connector port on the back panel of the router, then plug the power adapter into an electrical outlet or power strip. 2. Connect the router to your PC. · PC with Ethernet adapter: Connect an Ethernet cable between an available Ethernet port of the router and the Ethernet port of your PC. Turn on the router by pressing the POWER button on its back panel. Make sure that the Ethernet · PC with Wi-Fi adapter: Turn on the router by pressing the POWER button on its obtain an IP address automatically. Connect to the network R3-2.4G-xxxx (for operating in the 2.4GHz band) or R3-5G-xxxx (for operating in the 5GHz band). Use wireless password from the device label. 3. Start a web browser. In the address bar of the web browser, enter the IPaddress of the router (by default, 192.168.0.1). Press the Enter key. page of the Setup Wizard. 4. Click the Next button. 5. Select a Mode (Router, Bridge/AP or WISP) 6. Click the Next Wizard or the When the web-based interface is accessed the next time and after, the login page opens. Enter the username (admin) in the Username Password LOGIN button. To exit the web-based interface, select the Logout menu section. TROUBLESHOOTING default settings? You can restore the factory default settings via the hardware RESET button located on the back side of the router. 1. Use a small paperclip to activate the button; insert it into the hole (with the device turned on), push, and hold for 10 seconds. 2. Release the button and wait until the router is rebooted (about a minute or two). Then access the web-based interface (see the Default Settings section of the Below are some steps applicable to the most common issues. 1. Check the LEDs on the top panel of the router. The following LEDs should be solid or blinking blue : POWER, INTERNET, LAN (corresponding to the LAN ports of the router to which devices from the router's local area network are connected), 2.4GHz WLAN and 5GHz WLAN (if the 2.4GHz or 5GHz wireless network correspondingly is ON and in use). 2. Make sure that all cables are connected properly. Contact your ISP to make sure that the relevant service is available and that you use correct connection settings. FCC Caution. This device complies with part 15 of the FCC Rules. Operation is subject to the f ollowing two conditions: (1) This device may not cause harmf ul interf erence, and (2) this device must accept any interf erence received, including interf erence that may cause undesired operation. Any Changes or modif ications not expressly approved by the party responsible f or compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and f ound to comply with the limits f or a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmf ul interf erence in a residential installation. This equipment generates uses and can radiate radio f requency energy and, if not installed and used in accordance with the instructions, may cause harmf ul interf erence to radio communications. However, there is no guarantee that interf erence will not occur in a particular installation. If this equipment does cause harmf ul interf erence to radio or television reception, which can be determined by turning the equipment of f and on, the user is encouraged to try to correct the interf erence by one or more of the f ollowing measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit dif f erent f rom that to which the receiver is connected. -Consult the dealer or an experienced radio/ TV technician f or help. RF warning f or Mobile device: This equipment complies with FCC radiation exposure limits set f orth f or an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator&your body.