PLT Solutions
User Guide for PLT models including: C423100 4 Pack Led Multi Color Changing Tape Lights with Remote, C423100, 4 Pack Led Multi Color Changing Tape Lights with Remote, Lights with Remote
4 Ft. Led Rgbw Tape Light/Strip Light Kit
File Info : application/pdf, 9 Pages, 1.74MB
DocumentDocumentItem #1005 875 035 Model #C423100 USE AND CARE GUIDE 4 PACK LED MULTI-COLOR CHANGING TAPE LIGHTS WITH REMOTE OFF ON R G B W Flash Strobe Fade Smooth +12V G R B W +12V G R B W +12V G R B W +12V G R B W +12V G R B W +12V G R B W +12V G R B W +12V G R B W Any further questions or interests, please visit www.pltsolutions.com Pre-Installation (continued) PACKAGE CONTENTS A +12V G R B W +12V G R B W +12V G R B W +12V G R B W +12V G R B W +12V G R B B W +12V G R B W +12V G R B W C OFF ON R G B W Flash Strobe Fade Smooth D Part Description A Adapter B 12 in. LED strip C Infrared receiver (Assembled to the adapter (A)) D Remote E Connector wire F Large connector wire E F Quantity 1 4 1 1 1 2 Any further questions or interests, please visit www.pltsolutions.com Installation 1 Installation considerations What is the best layout configuration for your installation? How will you run and conceal the wires to your LED tape lighting? Temporarily mounting the LED light strip using painter's tape allows you to experiment with tape light positioning before permanent installation. IMPORTANT: Using painter's tape or masking tape, temporarily place the LED light strip into your desired mounting position. Power on the LEDs to make sure you are achieving the desired lighting effect before removing the 3M paper backing for final installation. 2 Connecting LED tape and adapter Use the following four ways to connect the LED tape and adapter according to installation requirements. · Connect LED tape to connector · Connect connector to LED tape · Connect LED tape to LED tape · Connect connector to connector +12V G R B W Connect LED tape to connector +12V G R B W Connect connector to LED tape NOTE: Connect LED tape to connector by aligning at the +12V on the LED tape and the arrow on the connector. NOTE: Connect connector to LED tape by aligning at the arrow on the connector and the +12V on the LED tape. +12V G R B W +12V G R B W Connect LED tape to LED tape NOTE: Connect LED tape to LED tape by aligning at the +12V on the LED tape. Connect connector to connector NOTE: Connect connector to connector by aligning at the arrows on the connectors. Any further questions or interests, please visit www.pltsolutions.com Installation (continued) 3 Cutting the LED strip (optional) By cutting the strip and exposing the copper pads, optional connector (C760011) or accessory (C760110) pack can be used for a more custom installation. +12V G R B W +12V G R B W +12V G R B W Optional connector (C760011) Cut LED tape in center of copper pads Optional accessory (C760110) Connect connector to LED tape 4 Preparing the assembly location Power the LED tape lighting and temporarily hold or tape into position with painter's tape or masking tape do not remove the 3M paper backing. Adjust the lighting to various angles and positions to get the desired level of illumination and lighting appearance. If the LEDs create undesirable light spots on walls, or reflections, reposition the tape light strip farther aways from surfaces or try a different mounting angle. Once you have determined your final mounting position, clean the surface to ensure the 3M self-adhesive backing will adhere properly. IMPORTANT: Before removing the 3M paper backing, it is important to test the LED strip in the space you intend to light. Once the 3M paper backing is removed and the lighting is fully installed, you cannot reposition or move the LED tape light to another location. The tape may not stick securely. Any further questions or interests, please visit www.pltsolutions.com Installation (continued) 5 Installing the LED strip 5A Tape method: Working from one end to the other, remove the 3M paper backing and press into place. Press between the LEDs to help ensure secure contact with the mounting surface. Avoid pressing on the individual LEDs as this could damage the LED solder connections. 5B Clip and screw method: Place the LED strip (B) in the desired position. Use the clips (BB) and screws (AA) to secure the LED strip as shown. Clips should be placed in open areas of the strip. Do not cover the LED lights. Plug the adapter (A) into the wall receptacle and then use the remote (D) to turn the LEDs on. 5A 5B AA B A BB NOTE: a. b. c. LED Chip Angle 90° Angle 60° a60° Correct a<60° lncorrect lncorrect a. Use an angle greater or equal to 90 degrees when there is an LED chip on the corner while placing the strip in a concave position. (Angle90°) b. Use an angle greater or equal to 60 degrees when there is no LED chip on the corner while placing the strip in a concave position. (Angle60°) c. Use an angle greater or equal to 60 degrees when there is an LED chip on the corner while placing the strip in a convex position. (Angle60°) In the convex position the angle should not reach 90 degrees. See above diagram. Any further questions or interests, please visit www.pltsolutions.com Installation (continued) 6 Installing the infrared receiver A B There are two options: A. Remove the protective tape from the adhesive back of infrared receiver (C), then place the infrared receiver (C) onto the position and press to ensure proper adhesion to the surface. B. Use the two screws to install the infrared receiver onto the position. C +12V G R B W +12V G R B W NOTE: AB Correct Smooth Fade Strobe Flash W ON B OFF G R Smooth Fade Strobe Flash W B 3m 60° 3m 5m OFF ON R G B W Flash Strobe Fade Smooth Incorrect OFF ON A. The sensor efficiency distance is 5 meters and the sensor efficiency angle is about 60°. B. The infrared receiver must face transmitter to operate properly. G R Any further questions or interests, please visit www.pltsolutions.com Installation (continued) 7 Connecting to the power supply Connect the adapter (A) to a power outlet. A Connect the adapter plug to infrared receiver controller Adapter with plug LED strip light Infrared receiver controller Infrared receiver Any further questions or interests, please visit www.pltsolutions.com Operation 1 Using the remote Direct the remote (D) towards the infrared receiver (C) to change RGBW colors of the strip. AB A--- Use to increase or decrease color brightness and to slow down or accelerate speed. OFF ON (NOTE: there are 10 light intensity options and 10 speed setting options) R G B W C B--- ON/OFF switch. Flash D Strobe E Fade F Smooth G C--- R,G,B,W: Choose color: red, green, blue, or warm white. D--- Flash key: 7 color jump change. E--- Strobe key: Strobe color effect. F--- Fade key: 7 color fade change. G--- Smooth key: 3 color jump change. NOTE: Sensor efficiency distance 5 meters. 2 Changing the battery To replace the battery, push in the tab on the side of the battery tray, and pull the tray out of the remote. Refer to the instructions on the back of the remote. OFF ON R G B W Flash Strobe Fade Smooth D Open Push Always purchase the correct size and grade of battery that is most suitable for the intended use. Clean the battery contacts and also those of the device prior to battery installation. Ensure the batteries are installed correctly with regard to polarity (+ and -). Remove batteries from the equipment when it is not being used for an extended period of time. Remove used batteries promptly. WARNING: The remote contains a CR2025 DC 3V button battery. If swallowed, it could cause severe injury or death within 2 hours. Seek medical attention immediately. Any further questions or interests, please visit www.pltsolutions.com Care and Cleaning To clean the fixture, disconnect the power by unplugging the adapter. Use a dry or slightly dampened, clean cloth to wipe the exterior surface of the fixture. Do not use any cleaners with chemicals, harsh abrasives, or solvents. Use only a dry, soft cloth to dust or wipe carefully. Troubleshooting Problem The LED will not light. Possible Cause The LED is burned out. The power is off. The power cord is not plugged in. The connector has faulty connections. The circuit breaker is turned off. The fuse blows or a circuit breaker trips when the light is turned on. A wire is exposed. Solution Discontinue use of the lamp. Ensure the power supply is turned on. Ensure the power cord is plugged into the outlet. Check the connections of the connectors. Ensure the circuit breaker is in the "ON" position. Discontinue use of the lamp. Unplug the unit from the wall. Contact a qualified electrician or call the Customer Care Service Team FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any further questions or interests, please visit www.pltsolutions.com