Mi Electric Scooter User Manual

Thank you for purchasing

Thank you for purchasing Mi Electric Scooter. It is a sports and recreational vehicle with style.

Contents

1. Package Contents
2. Product Overview
3. Assembly and Set-Up
4. Charge Your Scooter
5. How To Ride
6. Safety Instructions
7. Folding and Carrying
8. Daily Care and Maintenance
9. Specifications
10. Trademark and Legal statement
11. Certifications
12. Quick Setup

1 Package Contents

Assembled Electric Scooter, User Manual, Legal Statement Quick Start Guide, Warranty Card.

Accessories: Extended Nozzle Adapter, Screw x 4, Hexagon Wrench, Tire x 2, Charging Adapter.

Carefully check package contents, if anything is missing or damaged, please contact local customer service for support.

2 Product Overview

Headlight: Illuminates the path ahead.

Brake Lever: Activates the brake.

Folding Mechanism: Allows the scooter to be folded.

Wheel Motor: Provides propulsion.

Charging Port: Where the charging adapter connects.

Accelerator: Controls speed.

Control Panel: Displays information and modes.

Scooter Bell: Alerts others.

Buckle: Secures the folded scooter.

Brake Light: Indicates braking.

Disc Brake: Provides braking force.

Kickstand: Supports the scooter when parked.

Battery Compartment: Houses the battery.

Control Panel

Battery level display: Indicates the remaining battery charge with four lights. Each light represents 25% of the battery. Lights change from solid to flashing to off as power is consumed.

Mode display: The bottom light indicates the mode: white for regular mode, green for power-saving mode (max speed 11.2 mph).

Power button: Press to turn on the scooter. Press and hold for 2 seconds to turn off. Press to turn the headlight on/off. Double-press to switch modes.

3 Assembly and Set-Up

1. Fasten the handlebar stem on the headset, and put the kickstand down.
2. Attach the handlebar to the stem.
3. Tighten the screws onto both sides of the stem with the hexagon wrench.
4. After assembly, press the power button to check if it's working properly.

4 Charge Your Scooter

Lift up the rubber flap, plug the power adapter into the charging port. When charging is completed, put back the rubber flap.

5 How To Ride

1. Turn on the scooter and check the power indicator.
2. Step on the deck with one foot, and slowly kick off the other on the ground.
3. When the scooter starts to coast, put both feet on the deck and press the accelerator (the accelerator initiates once the coasting speed exceeds 3.1 mph).
4. Release the accelerator and the kinetic energy recovery system (KERS) initiates automatically to brake slowly; And squeeze the brake lever for a sudden brake.
5. Tilt your body to the steering direction as you turn, and slowly turn the handlebar.

Wear helmets and knee pads in case of falls and injuries when you learn to ride the scooter.

6 Safety Instructions

Watch out for safety risks.

• Do not ride in the rain.
• Keep your speed between 3.1-6.2 mph when you ride through speed bumps, elevator door sills, bumpy roads or other uneven surfaces. Slightly bend your knee to better adjust to mentioned surfaces.
• Look out for doors, elevators and other overhead obstacles.
• Do not accelerate when you go downhill.
• Do not press the accelerator when you're walking alongside the scooter.
• Always steer clear of obstacles.
• Do not hang bags or other heavy stuff on the handlebar.
• Keep both feet on the deck all time.
• Do not turn the handlebar violently during high-speed riding.
• Do not ride in a ponding that is higher than 0.78 inches.
• Do not ride with anyone else, including children.

Safety Reminder

• This electric scooter is a leisure device. Follow instructions in the manual and traffic laws and regulations.
• Be aware of risks and drive cautiously. The faster the scooter, the longer it takes to stop.
• Respect pedestrians' Right of Way. Ring your bell to give them a heads-up and slow your scooter to pass from their left.
• Follow safety instructions, especially in countries that lack relevant laws and regulations regarding electric scooters.
• Do not lend your scooter to someone unfamiliar with its operation. Ensure they wear safety gear.
• Check the scooter before every use. Stop riding immediately and call for professional support if you notice any issues.
• Do not keep your feet on the rear mudguard.
• Do not touch the disc brake.
• Do not keep your hands away from handlebar.
• Do not try riding up or down stairs, and jumping over obstacles.

7 Folding and Carrying

Fold: Make sure that the scooter's turned off. To fold, unlock the folding mechanism, and bend the handlebar stem to hook the buckle on the rear mudguard.

Open: Press the bell trigger to remove from the buckle, erect the handlebar and lock the folding structure.

Carry: Hold the handlebar stem with either one hand or both hands to carry.

8 Daily Care and Maintenance

Cleaning and storage

Wipe stains with a damp cloth. Use toothpaste and a toothbrush for stubborn stains, then wipe with a damp cloth. Polish scratches on plastic parts with sandpaper or other abrasive materials.

Notes: Do not use alcohol, gasoline, kerosene or other corrosive solvents. Do not wash with high-pressure water spray. Ensure the scooter is turned off, charging cable is unplugged, and the rubber flap is closed during cleaning.

Store the scooter indoors in a dry and cool place. Avoid excessive sunlight, overheating, and overcooling to prevent tire aging and prolong the scooter and battery pack's lifespan.

Battery maintenance

• Use original battery packs.
• Do not touch contacts, dismantle, or puncture the casing. Keep contacts away from metal objects to prevent short circuits.
• Use the original power adapter.
• Dispose of used batteries according to local regulations.
• Fully charge the battery after every use to prolong its lifespan.
• Avoid extreme temperatures (-4°F to 122°F). Do not leave the scooter in a car under direct sunlight for extended periods. Do not throw the battery pack into fire.
• If the scooter is idle for more than 30 days, fully charge the battery and recharge it every 60 days to prevent irreversible damage.
• Always charge before the battery is exhausted. The battery performs best at normal temperatures.

Note: A fully charged Mi Electric Scooter lasts 120-180 days. The built-in intelligent chip logs charging and discharging records. Damage from prolonged no charge is irreversible and beyond warranty.

Adjusting the disc brake

If the brake is too tight, use the M4 hexagon wrench to loosen the screws on the caliper, and slightly move back the brake cable. If the brake is too loose, loosen the screws, and slightly pull out the brake cable.

Adjust the handlebar

If the handlebar and its stem sway during riding, use the M5 hexagon wrench to tighten the screws on the folding mechanism.

How to use the extended nozzle adapter

If your tires are flat, remove the screw-on cap from the valve, and connect the extended nozzle adapter to the valve for pumping up.

Remove the outer and inner tires

1. Deflate the inner tire. Use a tool to press the core rod in the air valve to discharge air. Pinch the tire to discharge more air.
2. Pry up the outer tire from the hub using two crowbars. Separate one side of the outer tire from the hub.
3. Pull the air valve out of the air valve hole of the hub. Hold the air valve of the inner tire and pull the outer tire outwards slowly to avoid damaging the inner tire. Remove the inner tire from the hub.

Install the inner and outer tires

1. Fill a small amount of air into the deflated inner tire until it looks round.
2. Place the hub on a desk. Ensure the arrow on the outer tire is consistent with the forward direction of the wheel. Insert one side of the outer tire into the hub groove.
3. Insert the air valve of the inner tire into the air valve hole. Insert the inner tire into the outer tire clockwise. Ensure the air valve is not tilted. Insert the other side of the outer tire into the hub groove. Use a crowbar to install the remaining tire lips into the hub groove. Check if the inner tire is pressed by the outer tire lips.
4. Inflate the inner tire to 15-20 PSI. Check the safety lines on the outer tire to ensure consistent distance from the hub edge.
5. Inflate the inner tire to 45-50 PSI. Tighten the air valve cap.

9 Specifications

[1] Item height: from the ground to the top of the scooter;

[2] General range: measured when it is no wind and at 77°F, the scooter's fully charged to ride at an even speed of 9.3 mph on a flat surface with a load of 165.3 pounds.

Note: data and specifications may vary due to different models, and are subject to change without notice.

10 Trademark and Legal statement

MI is a registered trademark owned by Xiaomi Inc. Ninebot is a registered trademark of Ninebot (Tianjin) Technology Co., Ltd. All other trademarks and trade names are those of their respective owners.

©2017 Ninebot (Beijing) Technology Co., Ltd all rights reserved.

This manual included all functions and instructions when it is printed. Actual product may vary due to improved functions and design. Please scan the QR code in the back cover for the latest user manual.

Principal: Xiaomi Communications Co., Ltd.

Manufacturer: Ninebot (Changzhou) Tech Co., Ltd.

Address: 16F-17F, Block A, Building 3, No. 18, Changwu Mid Rd, Wujin Dist., Changzhou, Jiangsu, China.

11 Certifications

Federal Communications Commission (FCC) Compliance Statement for USA

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

Industry Canada (IC) Compliance Statement for Canada

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

CAN ICES-3 (B)/NMB-3(B)

European Union Compliance Statement

Battery recycling information for the European Union: Batteries or packaging for batteries are labeled in accordance with European Directive 2006/66/EC. Users must not dispose of batteries as unsorted municipal waste, but use the collection framework for return, recycling, and treatment.

Restriction of Hazardous Substances Directive (RoHS)

Ninebot (Changzhou) Tech Co., Ltd. products sold in the European Union meet the requirements of Directive 2011/65/EU.

Radio and Telecommunications Terminal Equipment Directive

CE

Ninebot (Changzhou) Tech Co., Ltd. declares that the wireless equipment listed in this section are in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.

Ninebot is not responsible for any changes or modifications not expressly approved by Ninebot. Such modifications could void the user's authority to operate the equipment.

For model: M365

FCC ID: 2ALS8-NS9633

IC: 22636-NS9633

12 Quick Setup

Control your Mi Electric Scooter and interacts it with other smart home devices in Mi Home App.

1. Download Mi Home App

Scan the QR code below or go to App Store to download Mi Home App.

[QR Code for Mi Home App]

2. Add a device

Open "My devices", select "+" on the upper right to add a device.