Hama BRAC Outdoor Sensor

Controls and Displays

A Measuring station

• 1. LED indicator
• 2. Battery compartment
• 3. CHANNEL slide switch = selects channel
• 4. Recess for wall mounting
• 5. LCD display

Explanation of Warning Symbols and Notes

• Warning: [!] This symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.
• Note: This symbol is used to indicate additional information or important notes.

Package Contents

• BRAC Outdoor Sensor
• These operating instructions

Safety Notes

The product is intended for private, non-commercial use only. Do not operate the product outside the power limits given in the specifications. Do not use the product in moist environments and avoid splashes. Do not use the product in the immediate vicinity of heaters or other heat sources or in direct sunlight. Do not use the product in areas where the use of electronic devices is not permitted. Do not put the product near interference fields, metal frames, computers, TVs, etc. Electronic devices and window frames can negatively affect the product’s functionality. Do not drop the product and do not expose it to any major shocks. Do not open the device or continue to operate it if it becomes damaged. Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts. Keep the packaging material out of the reach of children due to the risk of suffocation. Dispose of packaging material immediately according to locally applicable regulations. Do not modify the product in any way. Doing so voids the warranty. Use the product for its intended purpose only. Keep this product, as all electrical products, out of the reach of children! Use the item only in moderate climatic conditions.

Warning – Batteries

• When inserting batteries, note the correct polarity (+ and - markings) and insert the batteries accordingly. Failure to do so could result in the batteries leaking or exploding.
• Only use batteries that match the specified type. Keep the instructions for the correct choice of batteries included with the operating instructions of devices safe for future reference.
• Before you insert the batteries, clean the battery contacts and the polarity contacts.
• Do not allow children to change batteries without supervision.
• Replace all the batteries in a set at the same time.
• Do not mix old and new batteries, or batteries of different types or from different manufacturers.
• Remove the batteries from products that are not being used for an extended period (unless these are being kept ready for an emergency).
• Do not short-circuit batteries.
• Do not charge batteries.
• Do not burn batteries or heat them up.
• Never open, damage or swallow batteries or allow them to enter the environment. They can contain toxic, environmentally harmful heavy metals.
• Remove spent batteries from the product and dispose of them without delay.
• Avoid storing, charging and using in extreme temperatures and at extremely low atmospheric pressures (such as at high altitudes).
• Ensure that batteries with damaged housings do not come into contact with water.
• Keep batteries out of the reach of children.

Getting Started

• Open the battery compartment and insert two AA batteries, observing the correct polarity.
• Move the CHANNEL slide switch (3) to the left or right to select the channel on which the measuring station transmits.
• Then close the battery compartment cover.

Note: Before use, make sure that you insert the batteries in the measuring station first and then in the base station.

Operation

Connection to the measuring station

• To connect the base station and the measuring station, place the two devices as close together as possible.
• After you insert the batteries, the base station automatically searches for a connection to the measuring station and performs initial setup. If the device does not connect automatically, the manual search program on the base station must be started.

Note:

• Initial setup takes approximately 3 minutes.
• During the connection attempt, the radio symbol and the LED indicator (1) on the measuring station will flash.
• Do not press any buttons during setup. Otherwise, values may not be transmitted correctly and there is a risk of value errors and inaccuracies.
• The setup process is completed when the indoor and outdoor measurement data is displayed on the base station.
• The measured value is automatically updated by the base device about every 57 seconds.

Selecting the channel/Other measuring stations

Note:

• Ensure that the base station and measuring station are set to the same channel. Suitable base stations can be found at www.hama.com
• The transmission channel on the supplied measuring station can be changed/set (CH1, CH2, CH3).
• The measuring station is suitable for the following base stations: 76045 (only for model with 5 buttons), 123126, 186353, 136256, 136257, 136258, 136259, 186301 (2024 version), 186306, 186307, 186308, 186417, 186418, 186355, 186369, 185861, 222218, 222216, 222228, 222239

Care and Maintenance

• Only clean this product with a slightly damp, lint-free cloth and do not use aggressive cleaning agents.
• Make sure that water does not get into the product.

Warranty Disclaimer

Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or from failure to observe the operating instructions and/or safety notes.

Technical Data

Declaration of Conformity

Hereby, Hama GmbH & Co KG declares that the radio equipment type [00222237] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://uk.hama.com/00222237

• Frequency band(s): 433 MHz
• Maximum radio-frequency power transmitted: 0.133 mW