PRG-MUL2 - InventronicsApplication Notes - Inventronics
User Guide for inventronics models including: SSM-760S15AMGS 760W Programmable Driver with INV Digital Dimming, SSM-760S15AMGS, 760W Programmable Driver with INV Digital Dimming, Driver with INV Digital Dimming, Digital Dimming, Dimming
File Info : application/pdf, 15 Pages, 1.04MB
DocumentDocumentSSM-760SxxxMGS Rev.B 760W Programmable Driver with INV Digital Dimming Features Panel Mount Connectors Facilitates Installation Hot-plugging Protection Parallel LED Protection Ultra High Efficiency (Up to 95%) Full Power at Wide Output Current Range (Constant Power) Adjustable Output Current (AOC) with Programmability Isolated 0-10V/PWM/Resistor/3-Timer-Modes Dimmable Adjustable Dimming Curve INV Digital Dimming, UART Based Communication Protocol Dim-to-Off Minimum Dimming Level with 5% or 10% Selectable Hold Time Adjustable Fade Time Adjustable Always-on Auxiliary Power: 12Vdc, 250mA Low Inrush Current Output Lumen Compensation End-of-Life Indicator Input Surge Protection: DM 6kV, CM 10kV All-Around Protection: IOVP, IUVP, OVP, SCP, OTP IP66/IP67 and UL Dry/Damp/Wet Location TYPE HL, for Use in a Class I, Division 2 Hazardous (Classified) Location 5 Years Warranty Description The SSM-760SxxxMGS series is a 760W, constant-current, programmable and IP66/IP67 rated LED driver that operates from 249-528Vac input with excellent power factor. Created for many lighting applications including high mast, sports, UV-LED, aquaculture and horticulture, etc. It provides an auxiliary voltage and dim-to-off functionality for powering low voltage, wireless controls. The dimming control supports 0-10V dimming as well as two-way communication via Digital Dimming, a UART based communication protocol. The high efficiency of these drivers and compact metal case enables them to run cooler, significantly improving reliability and extending product life. To ensure trouble-free operation, protection is provided against input surge, input under voltage, input over voltage, output over voltage, short circuit, and over temperature. Models Adjustable Output Current Range(A) Full-Power Current Range(A)(1) Default Output Current(A) Output Voltage Range(Vdc) Max. Output Power(W) Typical Efficiency(2) Typical Power Factor 277Vac 480Vac 1.4-15.8 14-15.8 14 34-54 760 95.0% 0.99 0.96 Model Number(3)(4) SSM-760S15AMGS Notes: (1) Output current range with constant power at 760W. (2) Measured at 100% load and 480Vac input (see below "General Specifications" for details). (3) Certified voltage range: 277-480Vac (4) SELV output Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 1 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGS Rev.B 760W Programmable Driver with INV Digital Dimming I-V Operating Area 60 (1400, 54) (8400 , 54 ) 54 (10%Ioset, 760/Ioset) 48 42 (14000 , 54 ) (Ioset, 760/Ioset) (15800 , 48 ) Output Voltage(V) 36 30 24 0 (1580, 34) Good Performance Area Programmed Operating Area (15800, 34) (Ioset, 34 ) Allowed Operating Area 3160 6320 9480 12640 15800 Output Current (mA) Note : 14000mAIoset15800mA 18960 Input Specifications Parameter Input AC Voltage Input DC Voltage Input Frequency Leakage Current Input AC Current Inrush Current(I2t) PF THD Min. 249 Vac 352 Vdc 47 Hz - 0.90 - Typ. - Max. Notes 528 Vac 500 Vdc 63 Hz 0.75 MIU 0.70 mA 3.24 A 1.87 A 1.80 A2s 20% UL 8750; 480Vac/60Hz IEC 60598-1; 480Vac/60Hz Measured at 100% load and 277 Vac input. Measured at 100% load and 480 Vac input. At 480Vac input, 25C cold start, duration=6.06 ms, 10%Ipk-10%Ipk. At 277-480Vac,50-60Hz, 60%-100%Load (456 - 760W) Output Specifications Parameter Min. Output Current Tolerance Output Current Setting(Ioset Range) SSM-760S15AMGS Output Current Setting Range with Constant Power SSM-760S15AMGS Total Output Current Ripple (pk-pk) -5%Ioset 1400 mA 14000 mA - Typ. - - 5%Iomax Max. 5%Ioset 100% load Notes 15800 mA 15800 mA 10%Iomax 100% load, 20 MHz BW Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 2 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGS Rev.B 760W Programmable Driver with INV Digital Dimming Output Specifications (Continued) Parameter Min. Typ. Output Current Ripple at < 200 Hz (pk-pk) - - Startup Overshoot Current - - No Load Output Voltage SSM-760S15AMGS - - Line Regulation - - Load Regulation - - Turn-on Delay Time - - Temperature Coefficient of Ioset - 0.03%/C 12V Auxiliary Output Voltage 12V Auxiliary Output Source Current 12V Auxiliary Output Transient Peak Current@ 6W 10.8 V 0 mA - 12 V - 12V Auxiliary Output Transient Peak Current@ 10W - - Max. Notes 2%Iomax 70%-100% load 10%Iomax 100% load 60 V ±0.5% 100% load ±3.0% 0.5 s - Measured at 277-480Vac input, 60%100% Load Case temperature = 0C ~Tc max 13.2 V 250 mA 500 mA 850 mA Return terminal is "Dim-" 500mA peak for a maximum duration of 2.2 ms in a 6.0ms period during which time the average should not exceed 250mA. 850mA peak for a maximum duration of 1.3 ms in a 5.2ms period during which time the average should not exceed 250mA. General Specifications Parameter Min. Typ. Max. Notes Efficiency at 277 Vac input: SSM-760S15AMGS Io= 14000 mA Io= 15800 mA Efficiency at 400 Vac input: SSM-760S15AMGS Io= 14000 mA Io= 15800 mA Efficiency at 480 Vac input: SSM-760S15AMGS Io= 14000 mA Io= 15800 mA 91.5% 91.5% 92.5% 92.5% 93.0% 93.0% 93.5% 93.5% 94.5% 94.5% 95.0% 95.0% Measured at 100% load and steady-state temperature in 25C ambient; - (Efficiency will be about 2.0% lower if - measured immediately after startup.) Measured at 100% load and steady-state temperature in 25C ambient; - (Efficiency will be about 2.0% lower if - measured immediately after startup.) Measured at 100% load and steady-state temperature in 25C ambient; - (Efficiency will be about 2.0% lower if - measured immediately after startup.) Standby Power - 1.5 W - Measured at 480Vac/50Hz; Dimming off MTBF Lifetime Operating Case Temperature for Safety Tc_s Operating Case Temperature for Warranty Tc_w - -40°C -40°C 224,000 Hours 111,000 Hours 50,000 Hours - - - +90°C +80°C Measured at 480Vac input, 80%Load and 25C ambient temperature (MIL-HDBK217F) Measured at 480Vac input, 80%Load and 70C case temperature; See lifetime vs. Tc curve for the details Measured at 277Vac input, 100%Load and 40C ambient temperature Case temperature for 5 years warranty Humidity: 10%RH to 95%RH Storage Temperature -40°C - Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 +85°C Humidity: 5%RH to 95%RH 3 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGS Rev.B 760W Programmable Driver with INV Digital Dimming General Specifications (Continued) Parameter Dimensions Inches (L × W × H) Millimeters (L × W × H) Net Weight Min. Typ. Max. 15.35 × 4.25 × 1.91 390 × 108 × 48.5 - 3380 g - Notes With mounting ear 16.34 × 4.25 × 1.91 415 × 108 × 48.5 Dimming Specifications Parameter Absolute Maximum Voltage on the Vdim (+) Pin Source Current on Vdim (+)Pin Dimming Output Range with 10%-100% (Default) SSM-760S15AMGS SSM-760S15AMGS Dimming Output SSM-760S15AMGS Range with 5%-100% SSM-760S15AMGS (Settable) Recommended Dimming Input Range Dim off Voltage Min. -20 V 90 uA 10%Ioset 1400 mA 5%Ioset 700 mA 0 V 0.35 V Dim on Voltage 0.55 V Hysteresis - PWM_in High Level 3 V PWM_in Low Level -0.3 V PWM_in Frequency Range 200 Hz PWM_in Duty Cycle PWM Dimming off (Positive Logic) PWM Dimming on (Positive Logic) PWM Dimming off ( Negative Logic) PWM Dimming on ( Negative Logic) Hysteresis 1% 3% 5% 92% 90% - Typ. - 100 uA - - - 0.5 V 0.7 V 0.2 V 5% 7% 95% 93% 2% Max. 20 V 110 uA Ioset Notes Vdim(+) = 0 V 14000 mA Ioset 15800 mA Ioset 1400 mA Ioset 14000 mA Ioset 14000 mA Ioset 15800 mA Ioset 10 V 0.65 V 0.85 V 10 V 0.6 V 3 KHz 99% 8% 10% 97% 95% - 1400 mA Ioset 14000 mA Default 0-10V dimming mode. Dimming mode set to PWM in Inventronics Programing Software. Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 4 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGS Rev.B 760W Programmable Driver with INV Digital Dimming Safety &EMC Compliance Safety Category Standard UL/CUL CE UL 8750,CAN/CSA-C22.2 No. 250.13 EN 61347-1, EN 61347-2-13 CB IEC 61347-1, IEC 61347-2-13 EMI Standards Notes EN IEC 55015(1) EN IEC 61000-3-2 Conducted emission Test &Radiated emission Test Harmonic current emissions EN 61000-3-3 Voltage fluctuations & flicker FCC Part 15(1) EMS Standards ANSI C63.4 Class B This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: [1] this device may not cause harmful interference, and [2] this device must accept any interference received, including interference that may cause undesired Operation. Notes EN 61000-4-2 Electrostatic Discharge (ESD): 8 kV air discharge, 4 kV contact discharge EN 61000-4-3 Radio-Frequency Electromagnetic Field Susceptibility Test-RS EN 61000-4-4 EN 61000-4-5 EN 61000-4-6 EN 61000-4-8 EN 61000-4-11 Electrical Fast Transient / Burst-EFT Surge Immunity Test: AC Power Line: Differential Mode 6 kV, Common Mode 10 kV Conducted Radio Frequency Disturbances Test-CS Power Frequency Magnetic Field Test Voltage Dips EN 61547 Electromagnetic Immunity Requirements Applies To Lighting Equipment Note: (1) This LED driver meets the EMI specifications above, but EMI performance of a luminaire that contains it depends also on the other devices connected to the driver and on the fixture itself. Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 5 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGS Rev.B 760W Programmable Driver with INV Digital Dimming Lifetime(kHours) Lifetime vs. Case Temperature Lifetime vs. Case Temperature 135 120 105 90 75 60 45 30 15 0 30 35 40 45 50 55 60 65 70 75 80 85 90 Case Temperature () Inrush Current Waveform I Ipeak 50% Ipeak twidth Input AC Voltage Ipeak twidth (@ 50% Ipeak) 480V 19.9A 1.84ms t Efficiency vs. Load SSM-760S15AMGS(lo=14000mA) 100% Efficiency vs. Output Voltage SSM-760S15AMGS(lo=15800mA) 100% Efficiency vs. Output Voltage 95% 95% Efficiency Efficiency 90% 90% 85% 80% 277Vac 400Vac 480Vac 85% 80% 277Vac 400Vac 480Vac 75% 60% 70% 80% 90% 100% 75% 60% 70% 80% 90% 100% Normalized Output Voltage Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 Normalized Output Voltage 6 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGS Power Factor Rev.B 760W Programmable Driver with INV Digital Dimming PF 1.00 0.95 0.90 0.85 0.80 0.75 60% PF vs. Load 70% 80% Load 277Vac 400Vac 480Vac 90% 100% Total Harmonic Distortion 20% THD vs. Load 15% THD 10% 5% 0% 60% 70% 80% Load 277Vac 400Vac 480Vac 90% 100% Hot-plugging Protection This feature protects LEDs when connecting to a driver that is already powered on. This is disabled by default and can be enabled through the Inventronics Programing Software. LED threshold voltage (Vth) is the minimum voltage required for current to flow through the LED load. After this threshold is met, the LED forward voltage (Vf) increases as the current increases. Set Vth close to, but higher than the actual LED threshold voltage for optimized performance. The greater the difference between the Vth setting and the actual LED threshold voltage, the higher the overshoot current will be. The Vth setting must be lower than Vf. Please test, program, and tune this feature for each LED load design. Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 7 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGS Rev.B 760W Programmable Driver with INV Digital Dimming Hot-plugging Protection (Continued) Parameter Min. Typ. LED Threshold Voltage Setting 44 V - Hot-plugging Range Protection Setting Tolerance -2% - Max. 54 V 2% Notes Set Vth close to, but higher than the actual LED threshold voltage Parallel LED Protection This feature helps protect parallel LEDs from a high, overcurrent condition by limiting the voltage. This is disabled by default and can be enabled through the Inventronics Programing Software. Set V_overload close to, but higher than the maximum forward voltage for optimized performance. The greater the difference between the V_overload setting and the maximum forward voltage, the higher the overload stress will be. The V_overload setting must be higher than Vf. Please test, program, and tune this feature for each LED load design. Parameter Parallel LED Protection Overload Voltage Setting Range Setting Tolerance Min. 47 V -2% Typ. - Max. 56 V 2% Notes Set V_overload close to, but higher than the maximum LED forward voltage Protection Functions Parameter Min. Typ. Max. Notes Over Temperature Protection Short Circuit Protection Over Voltage Protection Input Under Voltage Protection (IUVP) Input Over Voltage Protection (IOVP) Input Protection Voltage Input Recovery Voltage Input Over Voltage Protection Input Over Voltage Recovery Max. of Input Over Voltage Decreases output current, returning to normal after over temperature is removed. Auto Recovery. No damage will occur when any output is short circuited. The output shall return to normal when the fault condition is removed. Limits output voltage at no load and in case the normal voltage limit fails. 220 Vac 230 Vac 230 Vac 240 Vac 240 Vac 250 Vac Turn off the output when the input voltage falls below protection voltage. Auto Recovery. The driver will restart when the input voltage exceeds recovery voltage. 550 Vac 570 Vac 530 Vac 550 Vac - - 590 Vac 570 Vac 590 Vac Turn off the output when the input voltage exceeds protection voltage. Auto Recovery. The driver will restart when the input voltage falls below recovery voltage. The driver can survive for 8 hours with a stable input voltage stress of 590Vac. Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 8 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGS Rev.B 760W Programmable Driver with INV Digital Dimming Input Under Voltage Protection Diagram Io Recovery Protection 230 Vac Input Over Voltage Protection Diagram Io Recovery Vin 240 Vac Protection 550 Vac Vin 570 Vac Dimming 0-10V Dimming The recommended implementation of the dimming control is provided below. Io/Ioset vs. Dimming Voltage V+ V- Inventronics Vaux LED Driver Dim+ Dim- Dimmer Io/Ioset 100% 80% 60% 40% 20% 0% 0 1 2 3 4 5 6 7 8 9 10 Dimming Voltage (V) Implementation 1: Positive logic 9 / 15 Specifications are subject to changes without notice. All specifications are typical at 25C unless otherwise stated. www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGS Rev.B 760W Programmable Driver with INV Digital Dimming Inventronics LED Driver Io/Ioset vs. Dimming Voltage 100% V+ 80% Io/Ioset V- 60% Vaux Dim+ 40% 20% Dim- Dimmer 0% 012345678 Dimming Voltage (V) Implementation 2: Negative logic 9 10 Notes: 1. Do NOT connect Dim- to the output V- or V+, otherwise the driver will not work properly. 2. The dimmer can also be replaced by an active 0-10V voltage source signal or passive components like zener. 3. When 0-10V negative logic dimming mode and Dim+ is open, the driver will dim to off and be standby. PWM Dimming The recommended implementation of the dimming control is provided below. lo/loset vs. PWM duty cycle Inventronics LED Driver V+ VVaux Dim+ Dim- 100% 80% lo/loset 60% PWM Signal 40% 20% 0% 0% 20% 40% 60% 80% PWM duty cycle Implementation 3: Positive logic 100% Inventronics LED Driver lo/loset vs. PWM duty cycle V+ VVaux Dim+ Dim- 100% 80% lo/loset 60% PWM Signal 40% 20% 0% 0% 20% 40% 60% 80% PWM duty cycle Implementation 4: Negative logic 100% Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 10 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGS Rev.B 760W Programmable Driver with INV Digital Dimming Notes: 1. Do NOT connect Dim- to the output V- or V+, otherwise the driver will not work properly. 2. When PWM negative logic dimming mode and Dim+ is open, the driver will dim to off and be standby. Resistor Dimming The recommended implementation of the dimming control is provided below. lo/loset vs. Rx Inventronics LED Driver V+ 100% V- 80% lo/loset Vaux 60% Dim+ 40% Rx Dim- 20% 0% 0k 10k 20k 30k 40k 50k 60k 70k 80k 90k 100k Rx () Implementation 5: Positive logic Inventronics LED Driver lo/loset vs. Rx V+ 100% V- 80% lo/loset Vaux 60% Dim+ 40% Rx Dim- 20% 0% 0k 10k 20k 30k 40k 50k 60k 70k 80k 90k 100k Rx () Implementation 6: Negative logic Notes: 1. Do NOT connect Dim- to the output V- or V+, otherwise the driver will not work properly. 2. When resistor negative logic dimming mode and Dim+ is open, the driver will dim to off and be standby. Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 11 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGS Rev.B 760W Programmable Driver with INV Digital Dimming Adjustable Dimming Curve 0-10V dimming curve can be set as corresponding dimming voltage by Inventronics Multi Programmer. Take the positive logic dimming as an example, the recommended implementation of the dimming control is provided below. Inventronics LED Driver Io/Ioset vs. Dimming Voltage 100% Y V+ 80% VVaux Dim+ Dim- Dimmer Io/Ioset 60% 40% 20% X 0% 012345678 Dimming Voltage(V) Implementation 7: Positive logic 9 10 Notes: 1. Do NOT connect Dim- to the output V- or V+, otherwise the driver will not work properly. 2. The dimmer can also be replaced by an active 0-10V voltage source signal or passive components like zener. 3. When dimming voltage X point is set to be smaller than Y point, the dimming curve is positive logic; conversely, when X point is set to be bigger than Y point, the dimming curve is negative logic. 4. For best dimming accuracy, the difference between X point and Y point is advised more than 4V. 5. Dimming off voltage adjustable. Time Dimming Time dimming control includes 3 kinds of modes, they are Self Adapting-Midnight, Self AdaptingPercentage and Traditional Timer. Self Adapting-Midnight: Automatically adjusts the dimming curve based on the on-time of past two days (if difference <15 minutes), assuming that the center point of the dimming curve is midnight local time. Self Adapting-Percentage: Automatically adjusts the on-time of each step by a constant percentage = (actual on-time for the past 2 days if difference <15 min) / (programmed on-time from the dimming curve). Traditional Timer: Follows the programmed timing curve after power on with no changes. Output Lumen Compensation Output Lumen Compensation (OLC) may be used to maintain constant light output over the life of the LEDs by driving them at a reduced current when new, then gradually increasing the drive current over time to counteract LED lumen degradation. Minimum Dimming Level with 5% or 10% Selectable The minimum dimming level can be set as 5% or 10% by Inventronics Multi Programmer,10% is default. Hold Time Adjustable When AC power is first applied to the LED driver, enabling a "Hold" period can allow devices powered by the Auxiliary voltage to stabilize before the driver fades up to the maximum dimming level. During this period, the driver will not respond to external dimming commands but will respond again after the hold time ends. Both the initial dimming percentage and the duration of this hold period can be adjusted by the Inventronics Multi Programmer. This function is disabled by default. Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 12 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGS Rev.B 760W Programmable Driver with INV Digital Dimming Fade Time Adjustable There is a "Fade" period after the "Hold" period. The soft-start time and dimming slope applied to all dimming transitions can be adjusted individually. It is adjusted by the Inventronics Multi Programmer. This function is disabled by default. End Of Life End-of-Life (EOL) is providing a visual notification to a user that the LED module has reached the end of manufacturer-specified life and that the replacement is recommended. Once active, an indication is given at each power-up of the driver, which the driver indicates this through a lower light output during the first 1 minute before normal operation is continued. Digital Dimming Inventronics Digital Dimming is a UART (Universal Asynchronous Receive Transmitter) based communication protocol. Please refer to Inventronics Digital Dimming file for details Programming Connection Diagram Note: The driver does not need to be powered on during the programming process. Please refer to PRG-MUL2 (Programmer) datasheet for details. Mechanical Outline INPUT(Panel Connector 3P Male) L2/N L1/L DIMMING(Panel Connector 3P Male) Waterproof Cap Dim+ DimVaux Tc V+ V- OUTPUT(Panel Connector 3P Female) Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 PROJ: Unspecified tolerance:±1 13 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGS Rev.B 760W Programmable Driver with INV Digital Dimming Note: This driver features UL Wet Location, IP67 panel mount connectors to streamline wiring in the field while still supporting stringent environmental conditions. The mating push-lock are not supplied by Inventronics. Please contact Wieland and Amphenol LTW or one of their suppliers for assistance sourcing the mating pushlock Location Vin Vo Series Wieland RST20i3 Rating voltage/current 600V/10A PN of connector on driver 96.032.1055.7 ALTW X-Lok,C-Size 300V/20A CC-03PMFS-QC800P PN of mating push-lock 96.031.0055.7 (Spring) or 96.031.4055.7 (Screw) CC-03BFMB-QL8APP Dim ALTW X-Lok,A-Size 300V/5A Dim ALTW X-Lok,A-Size Waterproof Cap / AD-03PMMS-QC8001 CAP-WAAMQPC1 AD-03BFFB-QL8AP0 / RoHS Compliance Our products comply with reference to RoHS Directive (EU) 2015/863 amending 2011/65/EU, calling for the elimination of lead and other hazardous substances from electronic products. Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 14 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGS Rev.B Revision History Change Date Rev. Item 2022-10-28 A Datasheet Release Format Feature 2023-12-28 Safety &EMC Compliance B Inrush Current Waveform Dimming Mechanical Outline 760W Programmable Driver with INV Digital Dimming Description of Change From / / / / / / / To / Updated Updated Updated Updated Updated Updated Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 15 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com