4-Installation

⚠ Read "Safety Instructions" section first! Installation procedures must always be performed by the manufacturer, authorised service agent or a qualified person specified by the importer. To make the product ready for use, make sure that the electricity, tap water supply and water drainage systems are appropriate before calling the authorised service agent. If they are not, call a qualified technician and plumber to have the necessary arrangements carried out.

🛈 Preparation of the location and electrical, tap water and waste water installations at the place of installation is under customer's responsibility.

⚠ Installation and electrical connections must be carried out by the authorised service agent. Manufacturer shall not be held responsible for damages arising from processes carried out by unauthorised persons.

⚠ Prior to installation, check if the product has any defects on it. If the product is damaged, do not have it installed. Damaged products cause risks for your safety.

🛈 Make sure that the water inlet and discharge hoses are not folded, pinched or crushed while pushing the product into its place after installation or cleaning procedures.

🛈 The front of the appliance may not be removed on free-standing or under-the-counter models. The warranty will be void if this is done.

When placing the product, pay attention not to damage the floor, walls, piping, etc. Do not hold the product from its door or panel to move it.

Appropriate installation location

🛈 In the area where this product is installed, there must not be a lockable, sliding or hinged door that will restrict full opening of the product's door.

🛈 Make sure that you select a location that will allow you to load and unload the dishes in a fast and comfortable manner.

• ⚠ Place the product on a solid and flat floor that has sufficient load carrying capacity! The product must be installed on a flat surface in order for the door to be closed properly and securely.
• ⚠ Do not install the product at places where temperature may fall below 0°C.
• ⚠ Place the product on a hard floor. Do not place it on a long pile rug or similar surfaces.

⚠ Do not place the product on the power cable.

🛈 Make sure that you select a location that will allow you to load and unload the dishes in a fast and comfortable manner.

Install the product at a place close to the tap and the drain hole. Select the installation location by considering that it will not be changed after the connections are made.

Connecting water supply

🛈 We recommend installing a filter at the water inlet in order to prevent the dirt (sand, clay, rust) in the mains or water installation of your home from damaging the machine or the dishes.

Permitted water temperature

Permitted water temperature: up to 25°C (60°C for products equipped with Aquasafe+; please refer to Aquasafe+ section)

The dishwasher may not be connected to open warm water devices or flow-through water heaters.

NOTICE: Do not use an old or used water inlet hose on the new product. Use the new water inlet hose supplied with the product. Do not make extension at the hoses.

NOTICE: Connect the water inlet hose directly to the water tap. Pressure coming from the tap should be 0.3 bars minimum and 10 bars maximum. If the water pressure exceeds 10 bars, a pressure relief valve should be installed in between.

NOTICE: The water supply and draining hoses must be securely fastened and remain undamaged.

NOTICE: Open the taps completely after making the connections to check for water leaks.

Diagram showing water inlet connection options with 3/4-inch and 1/2-inch fittings, labeled CH, DK, S, N, SF.

Aquasafe+

(depends on the model)

The Aquasafe+ system protects against water leaks that may occur at the hose inlet. Water contact with the valve box of the system must be avoided to prevent damage to the electrical system.

Diagram illustrating the Aquasafe+ component, a valve box connected to the water inlet hose.

⚠ As the hose set contains electrical connections and assemblies, never shorten or lengthen the hose with extension hoses.

⚠ If the Aquasafe+ system is damaged, unplug the product and call the authorised service agent.

Connection to the drain

Water discharge hose can directly be connected to the drain hole or sink's drainage. See the installation manual supplied with your machine for detailed information.

Diagrams illustrating methods for connecting the water discharge hose to a sink trap or a drain pipe.

Diagram showing recommended minimum (500mm) and maximum (1000mm) heights for the drain pipe connection.

🛈 Drain pipe must be connected to the sewage system and it should not be connected to any surface water.

Adjusting the feet

If the door of the product cannot be closed properly or if the product rocks when you push it slightly, then you need to adjust the feet of the product. Adjust the feet of the product as illustrated in the installation manual supplied with the product.

⚠ Steam may escape if the door of the dishwasher is not adjusted properly. Hot steam may cause serious burns and injuries and damage your furniture.

Electrical connection

⚠ Connect the product to a grounded outlet protected by a fuse complying with the values in the "Technical specifications" table. Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations.

• Connection must comply with national regulations.
• Power cable plug must be easily accessible after installation.
• Plug in the product to a grounded socket which is protected by a fuse of 10 Amperes.
• The specified voltage must be equal to your mains voltage.

⚠ Do not make connections via extension cables or multi-plugs.

⚠ Damaged power cables must be replaced by the authorised service agent.