Lightspeed 955 Access Instructional Audio System
Quick Start Guide
Connect Power to the 955 Access
Connect the provided power supply to the 955 Access unit and plug the cord into an AC outlet. Upon connection, the 955 Access will power on, and its power indicator light will glow.
Diagram: The 955 Access unit is shown with ports labeled 'POWER', 'MICROPHONE', 'AUDIO IN', 'TONE', and 'AUDIO OUT'. A 'POWER LIGHT' indicator is also shown.
Using the Flexmike
To use the Flexmike microphone:
- Remove the microphone from its charger.
- Press the power/mute button to unmute.
- Hold the microphone near your mouth and begin speaking.
For optimal sound, align the microphone with your collarbone and adjust the volume as needed.
Diagram: The Flexmike microphone is depicted with a 'POWER/MUTE BUTTON'. Indicator lights are labeled 'TALK (BLUE)' and 'MUTE (WHITE)'. Text prompts to 'ALIGN WITH COLLARBONE' and 'ADJUST VOLUME'.
Using the Sharemike
To use the Sharemike microphone:
- Remove the microphone from its charger.
- Press the power/mute button to begin speaking.
Adjust the volume as needed.
Diagram: The Sharemike microphone is shown with a 'POWER/MUTE BUTTON'. Indicator lights are labeled 'TALK (BLUE)' and 'MUTE (WHITE)'. Text prompts to 'ADJUST VOLUME'.
Charge Microphones Nightly
Place the microphones into the cradle charger. The power status indicator light on the charger will glow red while charging.
It takes approximately 5-6 hours to fully charge the microphone battery.
When charging is complete, the power status indicator light will glow green.
Diagram: An illustration shows microphones being placed into a charging cradle. The cradle has indicator lights. Text labels indicate 'NORMAL OPERATION', 'CHARGING IN PROGRESS' (red light), and 'CHARGING COMPLETE' (green light). The 'POWER STATUS LIGHT' is highlighted.
Using a Wireless Audio Link
You can connect your second microphone to your computer's USB port to enable a wireless two-way audio link.
Send Audio From the Computer
To send audio from your computer (e.g., videos, video conferencing, audiobooks, music) to the 955 Access system and speakers, connect the microphone to your computer using a USB-C cable. Open your computer's sound settings and select 'FlexmikeAudio' as the microphone and speaker.
Send Audio To the Computer
To ensure the teacher's Flexmike and any student microphones are clearly picked up by a video conferencing solution, connect the microphone to your computer using a USB-C cable.
Diagram: One illustration shows a laptop connected via a USB-C cable to a microphone. Text indicates this is for sending audio from the computer. Another illustration shows a microphone connected to the 955 Access unit, indicating sending audio to the system. A note states: "USB cable sold separately. Lightspeed offers a USB-A to USB-C cable for sale (part #USBC)."
Pairing Microphones to 955 Access
Your system is shipped with microphones and base units pre-paired for quick and easy use. If you need to pair new components, follow this process:
With a paperclip, push the register button on the back of the 955 Access unit.
Diagram: The back of the 955 Access unit is shown with ports labeled 'AUDIO INPUTS', 'REGISTER', 'DC INPUT 24V/2.5A'. An instruction indicates to 'Insert paper clip to press register button'.
From a powered-off state, press and hold the power button for five seconds until the 'MIC 1' and 'MIC 2' indicator lights start flashing. Release the button and allow the pairing process to finish.
Diagram: An illustration shows a hand holding a microphone near the 955 Access unit, with a finger pressing the 'POWER BUTTON' on the microphone.
The 'STATUS LIGHT' on the 955 Access unit will light up, indicating the pairing process is complete. The 'MIC 1' or 'MIC 2' indicator light on the microphone will remain illuminated.
Diagram: The front of the 955 Access unit is shown with ports labeled 'POWER', 'MICROPHONE', 'AUDIO IN', 'TONE', 'AUDIO OUT', and a 'STATUS LIGHT'.
For complete operating instructions, visit www.lightspeed-tek.com/955N-usermanual or scan the 2D barcode.
