User Manual for MEAN WELL models including: ELG-100 Series 70 100W Constant Voltage Plus Constant Current LED Driver, ELG-100 Series, 70 100W Constant Voltage Plus Constant Current LED Driver, Constant Voltage Plus Constant Current LED Driver, Voltage Plus Constant Current LED Driver, Constant Current LED Driver, Current LED Driver, LED Driver, Driver
11 ott 2024 — All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25℃ of ambient temperature. 2. Please refer to "DRIVING METHODS OF ...
AC/L(Brown) AC/N(Blue) DIMMING OPERATION ELG-100 Applying additive 0 ~ 10VDC Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz):
File Info : application/pdf, 11 Pages, 1.55MB
DocumentDocumentE L G - 1 0 0 70~100W Constant Voltage + Constant Current LED Driver
series
User's Manual
IP65 IP67
IS 15885(Part 2/Sec13)
THOMAS SAMUEL
THOMAS SAMUEL
R-41027766
(Please refer safety description)
{
A
Dx
File Name:ELG-100-SPEC 2024-01-08
E L G - 1 0 0 70~100W Constant Voltage + Constant Current LED Driver
series
SPECIFICATION
MODEL
ELG-100-24
ELG-100-36
ELG-100-42
ELG-100-48
DC VOLTAGE
24V
CONSTANT CURRENT REGION Note.2 12 ~ 24V
RATED CURRENT
4.0A
36V 18 ~ 36V 2.66A
42V 21 ~ 42V 2.28A
48V 24 ~ 48V 2A
200VAC ~ 305VAC
RATED POWER
96W
95.76W
95.76W
96W
100VAC ~ 180VAC
70W
70W
70W
70W
RIPPLE & NOISE (max.) Note.3 200mVp-p
250mVp-p
250mVp-p
300mVp-p
OUTPUT
VOLTAGE ADJ. RANGE
Adjustable for A/AB-Type only (via the built-in potentiometer)
21.6 ~ 26.4V
32.4 ~ 39.6V
37.8 ~ 46.2V
43.2 ~ 52.8V
CURRENT ADJ. RANGE
Adjustable for A/AB-Type only (via the built-in potentiometer)
2 ~ 4A
1.33 ~ 2.66A
1.14 ~ 2.28A
1 ~ 2A
VOLTAGE TOLERANCE Note.4 ±3.0%
±2.5%
±2.5%
±2.0%
LINE REGULATION
±0.5%
±0.5%
±0.5%
±0.5%
LOAD REGULATION
±1.0%
±1.0%
±0.5%
±0.5%
SETUP, RISE TIME Note.6 1000ms, 80ms/115VAC 500ms, 100ms/230VAC
HOLD UP TIME (Typ.)
15ms/115VAC 10ms/230VAC
VOLTAGE RANGE
Note.5
100 ~ 305VAC 142 ~ 431VDC continue,320VAC for 24Hrs; 360VAC for 1Hr (Please refer to "STATIC CHARACTERISTIC" section)
FREQUENCY RANGE
47 ~ 63Hz
POWER FACTOR
PF0.97/115VAC, PF0.95/230VAC, PF0.92/277VAC@full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)
ELG-100-54 54V 27 ~ 54V 1.78A
96.12W
70W 350mVp-p
48.6 ~ 59.4V
0.89 ~ 1.78A ±2.0% ±0.5% ±0.5%
TOTAL HARMONIC DISTORTION
THD< 20%(@load50%/115VC; @load60%/230VAC; @load75%/277VAC) (Please refer to "TOTAL HARMONIC DISTORTION(THD)" section)
INPUT
EFFICIENCY (Typ.)
88%
89%
90%
90%
91%
AC CURRENT INRUSH CURRENT(Typ.)
1.1A / 115VAC 0.6A / 230VAC 0.5A/277VAC COLD START 60A(twidth=850s measured at 50% Ipeak) at 230VAC; Per NEMA 410
MAX. No. of PSUs on 16A CIRCUIT BREAKER
3 units (circuit breaker of type B) / 6 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT
<0.75mA / 277VAC
NO LOAD / STANDBY POWER CONSUMPTION
No load power consumption <0.5W for Blank / A / Dx / D2-Type Standby power consumption <0.5W for B / AB / DA-Type
OVER CURRENT
95 ~ 108% Constant current limiting, recovers automatically after fault condition is removed
SHORT CIRCUIT PROTECTION
OVER VOLTAGE
Hiccup mode, recovers automatically after fault condition is removed
28 ~ 34V
41 ~ 48V
47 ~ 54V
Shut down output voltage, re-power on to recover
54 ~ 62V
62 ~ 72V
OVER TEMPERATURE WORKING TEMP. MAX. CASE TEMP.
ENVIRONMENT WORKING HUMIDITY STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT
Shut down output voltage, re-power on to recover Tcase=-40 ~ +90 (Please refer to " OUTPUT LOAD vs TEMPERATURE" section) Tcase=+90 20 ~ 95% RH non-condensing -40 ~ +80, 10 ~ 95% RH ±0.03%/ (0 ~ 60)
VIBRATION SAFETY STANDARDS
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
UL8750(type"HL"), CSA C22.2 No. 250.13-12; IEC/BS EN/EN/AS/NZS 61347-1, IEC/BS EN/EN/AS/NZS 61347-2-13 independent, BS EN/EN62384; EAC TP TC 004;BIS IS15885(for 24/24A/24B/24DA/36/36A/36B/42/42A/42ADA/42B/48/48B/54/54A/54ADA/54B only); GB19510.1, GB19510.14; IP65 or IP67;KC61347-1,KC61347-2-13 approved
SAFETY & EMC
DALI STANDARDS WITHSTAND VOLTAGE ISOLATION RESISTANCE
EMC EMISSION
Compliance to IEC62386-101,102,(207 by request) for DA Type only
I/P-O/P:3.75KVAC I/P-FG:2.0KVAC O/P-FG:1.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25/ 70% RH Compliance to BS EN/EN55015,BS EN/EN61000-3-2 Class C (@load60%); BS EN/EN61000-3-3;GB/T 17743, GB17625.1; EAC TP TC 020; KC KN15,KN61547
EMC IMMUNITY
Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11; BS EN/EN61547, light industry level (surge immunity Line-Earth 6KV, Line-Line 4KV); EAC TP TC 020; KC KN15,KN61547
MTBF OTHERS DIMENSION
2920.8K hrs min. Telcordia SR-332 (Bellcore) 199*63*35.5mm (L*W*H)
282.9Khrs min. MIL-HDBK-217F (25)
PACKING
0.85kg; 16pcs/14.2kg/0.72CUFT
NOTE
1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25 of ambient temperature.
2. Please refer to "DRIVING METHODS OF LED MODULE". For DA-Type, Constant Current region is 60%~100% of maximum voltage under rated power delivery.
3. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
4. Tolerance : includes set up tolerance, line regulation and load regulation.
5. De-rating may be needed under low input voltages. Please refer to "STATIC CHARACTERISTIC" sections for details.
6. Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time.
7. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final
equipment manufacturers must re-qualify EMC Directive on the complete installation again.
(as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf)
8. This series meets the typical life expectancy of >50,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 80 or less.
9. Please refer to the warranty statement on MEAN WELL's website at http://www.meanwell.com
10. The ambient temperature derating of 3.5/1000m with fanless models and of 5/1000m with fan models for operating altitude higher than 2000m(6500ft).
11. For any application note and IP water proof function installation caution, please refer our user manual before using.
https://www.meanwell.com/Upload/PDF/LED_EN.pdf
12. D2 models need to be programmed in the state of loading.
13.To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently connected to the mains.
Product Liability DisclaimerFor detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx
File Name:ELG-100-SPEC 2024-01-08
E L G - 1 0 0 70~100W Constant Voltage + Constant Current LED Driver
series
Block Diagram
PFC fosc : 50~120KHz PWM fosc : 60~130KHz
EMI FILTER
I/P
&
RECTIFIERS
PFC CIRCUIT
POWER
RECTIFIERS
Vo+
SWITCHING
& FILTER
Vo-
O.L.P.
O.T.P.
O.L.P.
PWM & PFC CONTROL
DETECTION CIRCUIT
O.V.P.
CASE :Protective Earth
DRIVING METHODS OF LED MODULE
This series is able to work in either Constant Current mode (a direct drive way) or Constant Voltage mode (usually through additional DC/DC driver) to drive the LEDs.
100
Vo(%)
50 (min.)
(A) Constant
Voltage area
(B) Constant Current area
(C) Hiccup Protection
50
100
Io(%)
Typical output current normalized by rated current (%)
In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Should there be any compatibility issues, please contact MEAN WELL.
This characteristic applies to Blank/A/B/AB/DX/D2-Type, For DA-Type, the Constant Current area is 60%~100% Vo.
File Name:ELG-100-SPEC 2024-01-08
E L G - 1 0 0 70~100W Constant Voltage + Constant Current LED Driver
series
DIMMING OPERATION
AC/N(Blue) AC/L(Brown)
ELG-100
DIM+(Purple)* DIM-(Pink)** Vo-(Black) Vo+(Red)
3 in 1 dimming function (for B/AB-Type)
Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-: 0 ~ 10VDC, or 10V PWM signal or resistance.
Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: 100A (typ.)
* DIM+ for B/AB-Type DA+ for DA-Type PROG+ for D2-Type
* *DIM- for B/AB-Type DA- for DA-Type PROG- for D2-Type
Applying additive 0 ~ 10VDC
100%
90%
Vo+ +
80%
+
70%
Output current (%)
Vo-
60%
-
50%
DIM+ +
40%
Additive Voltage
30%
-
20%
DIM-
10%
"DO NOT connect "DIM- to Vo-"
0% 0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V
Dimming input: Additive voltage
Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz):
Vo+ +
+
Vo-
-
DIM+
Additive PWM signal DIM-
"DO NOT connect "DIM- to Vo-"
Output current (%)
100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 0%
0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input
Applying additive resistance:
100%
Output current (%)
Vo+ +
VoDIM+
90%
+
80%
70%
-
60%
50%
40%
Additive Resistance
30%
DIM-
20%
"DO NOT connect "DIM- to Vo-"
10%
0% Short 10K/N 20K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N
(N=driver quantity for synchronized dimming operation)
Dimming input: Additive resistance
Note : 1. Min. dimming level is about 8% and the output current is not defined when 0%< Iout<8%.
2. The output current could drop down to 0% when dimming input is about 0k or 0Vdc, or 10V PWM signal with 0% duty cycle.
File Name:ELG-100-SPEC 2024-01-08
E L G - 1 0 0 70~100W Constant Voltage + Constant Current LED Driver
series
DALI Interface (primary side; for DA-Type) Apply DALI signal between DA+ and DA-. DALI protocol comprises 16 groups and 64 addresses. First step is fixed at 8% of output.
Smart timer dimming function (for Dxx-Type by User definition) MEAN WELL Smart timer dimming primarily provides the adaptive proportion dimming profile for the output constant current level to perform up to 14 consecutive hours. 3 dimming profiles hereunder are defined accounting for the most frequently seen applications. If other options may be needed, please contact MEAN WELL for details.
Ex : D01-Type: the profile recommended for residential lighting
Set up for D01-Type in Smart timer dimming software program:
T1
T2
T3
T4
TIME**
06:00
07:00
11:00
---
LEVEL** 100%
70%
50%
70%
Dimming Level(%)
Operating Time(HH:MM)
**: TIME matches Operating Time in the diagram whereas LEVEL matches Dimming Level. Example: If a residential lighting application adopts D01-Type, when turning on the power supply at 6:00pm, for instance:
[1] The power supply will switch to the constant current level at 100% starting from 6:00pm. [2] The power supply will switch to the constant current level at 70% in turn, starting from 0:00am, which is 06:00 after the power supply turns on. [3] The power supply will switch to the constant current level at 50% in turn, starting from 1:00am, which is 07:00 after the power supply turns on. [4] The power supply will switch to the constant current level at 70% in turn, starting from 5:00am, which is 11:00 after the power supply turns on.
The constant current level remains till 8:00am, which is 14:00 after the power supply turns on.
Ex: D02-Type: the profile recommended for street lighting
Set up for D02-Type in Smart timer dimming software program:
TIME** LEVEL**
T1 01:00 50%
T2 03:00 80%
T3 8:00 100%
T4
T5
11:00
---
60%
80%
Dimming Level(%)
Operating Time(HH:MM) **: TIME matches Operating Time in the diagram whereas LEVEL matches Dimming Level. Example: If a street lighting application adopts D02-Type, when turning on the power supply at 5:00pm, for instance: [1] The power supply will switch to the constant current level at 50% starting from 5:00pm. [2] The power supply will switch to the constant current level at 80% in turn, starting from 6:00pm, which is 01:00 after the power supply turns on. [3] The power supply will switch to the constant current level at 100% in turn, starting from 8:00pm, which is 03:00 after the power supply turns on. [4] The power supply will switch to the constant current level at 60% in turn, starting from 1:00am, which is 08:00 after the power supply turns on. [5] The power supply will switch to the constant current level at 80% in turn, starting from 4:00am, which is 11:00 after the power supply turns on. The
constant current level remains till 6:30am, which is 14:00 after the power supply turns on.
File Name:ELG-100-SPEC 2024-01-08
E L G - 1 0 0 70~100W Constant Voltage + Constant Current LED Driver
series
Ex: D03-Type: the profile recommended for tunnel lighting
Set up for D03-Type in Smart timer dimming software program:
T1
T2
T3
TIME**
01:30
11:00
---
LEVEL** 70%
100%
70%
Dimming Level(%)
Operating Time(HH:MM)
**: TIME matches Operating Time in the diagram whereas LEVEL matches Dimming Level. Example: If a tunnel lighting application adopts D03-Type, when turning on the power supply at 4:30pm, for instance: [1] The power supply will switch to the constant current level at 70% starting from 4:30pm. [2] The power supply will switch to the constant current level at 100% in turn, starting from 6:00pm, which is 01:30 after the power supply turns on. [3] The power supply will switch to the constant current level at 70% in turn, starting from 5:00am, which is 11:00 after the power supply turns on. The constant current level remains till 6:30am, which is 14:00 after the power supply turns on.
File Name:ELG-100-SPEC 2024-01-08
E L G - 1 0 0 70~100W Constant Voltage + Constant Current LED Driver
series
OUTPUT LOAD vs TEMPERATURE(Note.9)
LOAD (%)
THD LOAD (%)
100
80 230VAC input only
60
40
20
-40
-25 -10 0
15
30
50
60
70 (HORIZONTAL)
AMBIENT TEMPERATURE,Ta ()
LOAD (%)
100
80 230VAC input only
60
40
20
-40 -25 0
10
30
50
70
Tcase ()
85
90 (HORIZONTAL)
STATIC CHARACTERISTIC
100 90 80 70 60 50 40
100 120 140 160 180 200 240 250 260 270 280 305
INPUT VOLTAGE (V) 60Hz De-rating is needed under low input voltage.
PF
POWER FACTOR (PF) CHARACTERISTIC
Tcase at 80 Constant Current Mode
1 0 .9 8 0 .9 6 0 .9 4 0 .9 2
0 .9 0 .8 8 0 .8 6
50% 60% 70% 80% 90% 100% LOAD
2 7 7 V(1 0 0 W) 2 3 0 V(1 0 0 W) 115V(70W )
TOTAL HARMONIC DISTORTION (THD)
54V Model, Tcase at 80
22% 20% 18% 16% 14% 12% 10% 8% 6% 4% 2%
50%
60%
70%
80%
2 7 7 VAC (1 0 0 W) 2 3 0 VAC (1 0 0 W) 1 1 5 VAC (7 0 W )
90% 100%
LOAD
EFFICIENCY(%)
EFFICIENCY vs LOAD
ELG-100 series possess superior working efficiency that up to 91% can be reached in field applications. 54V Model, Tcase at 80
94
92
90
277V(100W)
88
230V(100W)
86
115V(870W)
84
82
80
50%
60%
70%
80%
90% 100%
LOAD
File Name:ELG-100-SPEC 2024-01-08
E L G - 1 0 0 70~100W Constant Voltage + Constant Current LED Driver
series
LIFE TIME
LIFETIME(Kh)
120
100
80
60
40
20
0
20
30
40
50
60
70
80
90
Tcase ( )
File Name:ELG-100-SPEC 2024-01-08
E L G - 1 0 0 70~100W Constant Voltage + Constant Current LED Driver
series
Mechanical Specification
Blank-Type
CASE NO.: 244A Unit:mm
199
188
300±20
175
300±20
AC/N(Blue) AC/L(Brown)
SJOW 17AWGx2C &H05RN-F 1.0mm2
tc
105
4-4.5
tc : Max. Case Temperature
SJOW 17AWGx2C &05RN-F 1.0mm2
Vo-(Black) Vo+(Red)
63 45.8 20 35 35.5
A-Type
300±20
AC/N(Blue) AC/L(Brown)
SJOW 17AWGx2C &H05RN-F 1.0mm2
63 45.8 20
199 188 175
tc
105
4-4.5
tc : Max. Case Temperature
300±20
SJOW 17AWGx2C &05RN-F 1.0mm2
Vo-(Black) Vo+(Red)
35 35.5
21.5
14 33
File Name:ELG-100-SPEC 2024-01-08
E L G - 1 0 0 70~100W Constant Voltage + Constant Current LED Driver
series
AB-Type
199
188
300±20
175
63 45.8 20
AC/N(Blue) AC/L(Brown)
SJOW 17AWGx2C &H05RN-F 1.0mm2
tc
105
4-4.5
tc : Max. Case Temperature
300±20
UL2517 20AWGx2C
SJOW 17AWGx2C &05RN-F 1.0mm2
DIM+(Purple) DIM-(Pink) Vo-(Black) Vo+(Red)
35 35.5
21.5
14 33
B/DA/D2-Type
199
188
300±20
175
AC/N(Blue) AC/L(Brown)
SJOW 17AWGx2C &H05RN-F 1.0mm2
tc
105
4-4.5
tc : Max. Case Temperature
300±20
UL2517 20AWGx2C
SJOW 17AWGx2C &05RN-F 1.0mm2
DIM+(Purple)* DIM-(Pink)** Vo-(Black) Vo+(Red)
* DIM+ for B-Type DA+ for DA-Type PROG+ for D2-Type
* *DIM- for B-Type DA- for DA-Type PROG- for D2-Type
63 45.8 20 35 35.5
File Name:ELG-100-SPEC 2024-01-08
E L G - 1 0 0 70~100W Constant Voltage + Constant Current LED Driver
series
3Y Model (3-wire input)
199
188
300±20
175
63 45.8 20
AC/N(Blue) AC/L(Brown) PE (Green/Yellow)
SJOW 17AWGx3C &H05RN-F 1.0mm2
tc
105
4-4.5
tc : Max. Case Temperature
Note1: Please connect the case to PE for the complete EMC deliverance and safety use. Note2: Please contact MEAN WELL for input wiring option with PE.
Recommend Mounting Direction
SJOW 17AWGx2C &05RN-F 1.0mm2
INSTALLATION MANUAL
Please refer to:http://www.meanwell.com/manual.html
File Name:ELG-100-SPEC 2024-01-08
MEAN WELL Switching Power Supply Manufacturer