RISCO eyeWAVE™ Wireless PIR Camera

Description

The eyeWAVE™ Wireless PIR Camera Detector is a battery-powered PIR detector with an integrated camera for visual verification. It is compatible with RISCO security systems.

Features:

• PIR coverage: 12m (40’) wide angle
• Camera resolution: VGA or QVGA with ~85° field-of-view
• Discreet IR flash for imaging in complete darkness up to 10m (33’)
• Sequence of images upon event, configurable number and FPS
• Events are ignored during disarm to save battery and for privacy
• On-demand images initiated from authorized Smartphone or web browser
• Two RF channels with separate antennas: one for control, second for image transmission
• Images stored on detector until transmission to panel is complete
• Includes 2 long-life 3V lithium batteries

Installation

Step 1: Preliminary Considerations

• Select the mounting location for best coverage of the area to be protected.
• Avoid touching the lens with fingers to prevent blurry images.
• Do not mount the detector facing direct sunlight, near heat sources, or metallic objects.
• Detection sectors should be oriented towards the wall, not towards windows or shutters.
• Choose mounting height according to coverage patterns (recommended: 2.20m to 2.50m, at least 40cm from the ceiling).
• For Pet friendly models, mount vertically at right angles to the floor and ensure pets cannot climb onto furniture to exceed 1.5m (5').

Step 2: Registering the Detector into the System

The eyeWAVE must identify itself to the system receiver through a device allocation (enrollment) process. This can be done via RF sequence registering, entering the detector’s 11-digit serial number, or using RF mode panel quick key programming.

From the panel: 2) Radio Devices > 1) Allocation > 1) By RF or 2) By Code.

Through the Configuration Software: Radio Device Allocation > Enter Serial Code: [045] + [8 digits]; Indexed: Automatic or manually designated 1-32; Accessory Type: 2-Way Detector. Then click Allocate.

Refer to the System Installer Manual for more information.

Step 3: Mounting the Detector

1. Open the knockout holes of the mounting bracket and use them as a template for mounting.
2. Fasten the cover to the base of the detector by inserting and fastening the screw into the hole located inside the battery compartment.
3. Insert the batteries and close the battery compartment cover.
4. Once the bracket is installed, slide and lock the detector onto the mounting bracket in reverse sequence.
5. Perform a Walk Test as described in the Walk Test section.
6. Insert and fasten screw (C) into the hole located at the bottom of the detector to lock the detector to the mounting bracket.

Step 4: Performing a Walk Test

To manually initiate a walk test from the control panel:

Installation Menu: 2) Testing > 2) Zone > 3) Walk Test > 1) Start Walk Test.

The detector remains in walk test mode until any key on the panel is pressed. Display test results as follows: Installation Menu: 2) Testing > 2) Zone > 3) Walk Test > 2) Walk Test Results.

Camera Configuration

Detector parameters can be modified from the keypad or the system configuration software.

PIR Settings:

• Sensitivity: High/Low (Default: Low)
• Supervision Time: 0-255 minutes (Default: 15 min)
• LED: On/Off (Default: On)
• Operation Mode: Walk Test (transmits after each detection) or Normal (Default).

Configure camera settings through the RISCO Configuration Software (right-click on the Serial Code field in the Zones node screen and click Additional..) or through the panel quick key programming sequence:

Programming > 2) Radio Devices > 2) Modification > 1) Zone [Select (1–32)] > 1) Parameters > 6) Advanced > 5) Camera Parameters:

• Images at Alarm: 3 (1 to 7 images)
• Image Interval: 0.5 sec (0.5, 1, 2 seconds)
• Pre-Alarm Image: Yes (Yes, No) (Image capture upon each arm)
• Image Resolution: QVGA (QVGA 320X240, VGA 640X480)
• Image Quality: High (High, Low)
• Colour Image: Colour (Colour, B&W)

Image upon request

Snapshot images can be taken using web/smartphone apps (on panels supporting these applications).

Event Reporting

Every event detected by the PIR camera is recorded into the camera’s memory, including date, time, event description, source, and a video record.

LED Status

• On: Alarm
• Blinking three times (in alarm mode): Low battery
• Blinking four times (in initial learning mode): Successful write operation

Diagnostics

Diagnostic tests can be performed on the detector using the keypad or configuration software to check battery status and communication with the panel. Refer to the System Installer Manual for details.

Battery Replacement

A low battery condition is indicated by a blinking LED on each transmission.

1. Remove the detector from the mounting bracket.
2. Open the battery cover.
3. Replace the batteries, paying attention to polarity.
4. Close the battery cover.

CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to local regulations.

Specifications

Electrical

• Battery Type: 2 x CR 123, 3V Lithium Battery
• Battery Life: 2 batteries – 3 year typical lifetime
• Current Consumption: 58 μA standby; 200 mA max. peak at capture with flash
• Supervision Transmission: 0-255 minutes
• RF transmitting frequencies: 868.65 MHz; 869.525 MHz for model RWX95CM8; 433.92 MHz; 916 MHz for model RWX95CM4

Optical

• Filtering: White Light Protection
• Pet friendly: Up to a 36 kg (80lb) animal (pet model)

Physical

• Size: 132 x 67.5 x 56 mm (5.1 x 2.6 x 2.2 in)
• Weight: 169 grams (5.96 oz.)

Environmental

• RF Immunity: According to EN50130-4
• Operating Temperature: -10°C to 55°C (14°F to 140°F)
• Storage Temperature: -20°C to 60°C (-4°F to 140°F)

Camera

• Type: CMOS digital image sensor
• Lux: 0 Lux (total darkness)
• View Angle: H 90° V 71°

Approvals

• EN50131-1, EN50131-2-2 Grade 2, EN50130-5 Environmental Class II, EN50131-6: Type C
• SSF 1014 v4, & Larmklass R.

Ordering Information

• RWX95CM8000A: 868.65 MHz 2-Way WL PIR & CAM Detector
• RWX95CMP800A: 868.65 MHz 2-Way WL PIR Pet & CAM Det.
• RWX95CM4000A: 433.92 MHz 2-Way WL PIR & CAM Detector
• RWX95CMP400A: 433.92 MHz 2-Way WL PIR Pet & CAM Det.

RED Compliance Statement

Hereby, RISCO Group declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. For the CE Declaration of Conformity please refer to our website: www.riscogroup.com.

Standard Limited Product Warranty

RISCO Ltd. guarantees its hardware products to be free from defects in materials and workmanship for a period of 24 months from the date of connection to the RISCO Cloud or from production date (for non-cloud connected products).

This warranty is for the benefit of the customer who purchased the product directly from RISCO or an authorized distributor. RISCO customer shall handle all interactions with its end users regarding the warranty.

Return Material Authorization: Customer must obtain an RMA number from RISCO prior to returning any product. The returned product must include a detailed description of the defect.

Limitations: The warranty does not apply if products have been subjected to improper operation, installation, neglect, abuse, alteration, modification, or repair without RISCO’s written approval, or damage from factors beyond RISCO’s control.

Batteries are explicitly excluded from the warranty.

RISCO disclaims all other warranties, expressed or implied, including warranties of merchantability or fitness for a particular purpose.

RISCO is not responsible for the performance of the end-user security system or for any personal injury or property loss. Correctly installed and maintained alarm systems may reduce risk but do not guarantee against events.

Contacting RISCO Group:

• United Kingdom: Tel: +44-(0)-161-655-5500, support-uk@riscogroup.com
• Belgium (Benelux): Tel: +32-2522-7622, support-be@riscogroup.com
• Spain: Tel: +34-91-490-2133, support-es@riscogroup.com
• France: Tel: +33-164-73-28-50, support-fr@riscogroup.com
• Italy: Tel: +39-02-66590054, support-it@riscogroup.com
• USA: Tel: +1-631-719-4400, support-usa@riscogroup.com
• Israel: Tel: +972-3-963-7777, support@riscogroup.com
• China (Shanghai): Tel: +86-21-52-39-0066, support-cn@riscogroup.com
• Australia: Tel: +1800-991-542, support-au@riscogroup.com