Fenix SILVGLOW Limited Edition AAA Flashlight
User Manual
Introduction
This manual provides detailed information for the Fenix SILVGLOW Limited Edition AAA Flashlight. Please read it carefully before use to ensure proper operation and safety.
Key Features ?
- Limited Edition design
- Compact and lightweight, ideal for everyday carry
- Utilizes a high-performance LED
- Multiple brightness levels and modes
- Durable aircraft-grade aluminum construction
- Water and dust resistant (IP rating typically specified)
- Powered by readily available AAA batteries
Specifications ?
| Parameter | Value |
|---|---|
| LED Type | High-performance LED (Specific model may vary) |
| Brightness Levels | (e.g., 5 Lumens, 50 Lumens, 150 Lumens) |
| Runtime | (e.g., Up to XX hours on lowest setting) |
| Beam Distance | (e.g., Up to XX meters) |
| Water Resistance | IPX-8 (e.g., submersible up to 2 meters for 30 minutes) |
| Impact Resistance | (e.g., 1.5 meters) |
| Battery Type | 1 x AAA Alkaline or Ni-MH battery |
| Dimensions | (e.g., Length: XX mm, Head Diameter: XX mm, Body Diameter: XX mm) |
| Weight | (e.g., XX grams excluding battery) |
| Material | A6061-T6 Aluminum (Hard-anodized anti-abrasive finish) |
Note: Specifications are subject to change without notice. Actual performance may vary based on environmental conditions and battery type.
Operation ⚙️
Turning On/Off:
Fully press the tail switch to turn the flashlight on. Press again to turn it off.
Mode Switching:
With the flashlight on, half-press the tail switch to cycle through the different brightness levels (e.g., Low -> Medium -> High). Fully press the switch to select a mode and keep the light on, or release it to return to the previous state if half-pressing.
Strobe Mode (if applicable):
To activate Strobe mode, quickly double half-press the tail switch from the ON state. Half-press again to exit Strobe.
Lockout Function (if applicable):
To prevent accidental activation, loosen the tail cap slightly (about 1/4 turn) or use the electronic lockout feature if available.
Battery Installation and Replacement
Unscrew the tail cap. Insert the AAA battery with the positive (+) end facing the head of the flashlight. Screw the tail cap back on securely.
Recommendation: Use high-quality AAA batteries for optimal performance. Remove batteries if the flashlight will not be used for an extended period.
Maintenance and Care
Keep the flashlight clean. Periodically clean the battery contacts with a dry cloth. Do not immerse the flashlight in water beyond its rated depth. Store in a cool, dry place.
O-ring Maintenance:
The rubber O-rings provide water resistance. Ensure they are clean and lubricated with silicone grease if necessary. Do not overtighten the tail cap or head assembly, as this can damage the O-rings.
Safety Precautions ⚠️
- Do not look directly into the flashlight beam, as it can cause temporary or permanent eye damage.
- Do not point the flashlight at people or animals.
- Keep out of reach of children.
- Do not disassemble or modify the flashlight, as this will void the warranty and may cause damage.
- Ensure batteries are inserted correctly, observing polarity.
- Dispose of used batteries responsibly according to local regulations.
Warranty Information
Fenix provides a limited lifetime warranty against defects in materials and workmanship for its products. For detailed warranty terms and conditions, please visit the official Fenix website or consult your retailer.
The Fenix SILVGLOW Limited Edition is covered by this warranty.
Diagram Description (Conceptual)
The Fenix SILVGLOW flashlight is a cylindrical device. At the front is the head, containing a reflective optic and a protective lens, which focuses the light from the LED. The main body is a tube designed for grip and housing the battery. At the rear is the tail cap, which typically contains a durable switch mechanism for operation. The construction is primarily aircraft-grade aluminum with a hard-anodized finish.
