Kanto TE300SG

Thank You for Choosing Kanto

Read these instructions fully before assembly and installation. Ensure there are no defective or missing parts. Kanto is not liable for property damage or injury caused by incorrect mounting, assembly, lifting, or use.

Supplied Parts and Hardware

Parts include:

• Screws: A (M4 x 16 mm), B (M5 x 16 mm), C (M5 x 30 mm), D (M6 x 16 mm), E (M6 x 35 mm), F (M8 x 20 mm), G (M8 x 35 mm), H (M8 x 50 mm)
• Spacers: I (5 mm), J (10 mm), K (14 mm)
• Washers/Adapters: L (M4/M5/M6)
• Lag Bolts: M (M8)
• Concrete Anchor: N (M8 x 50mm)
• Security Torx Screw: P
• Template

Required Tools:

• Socket Set
• Pencil
• Level
• Measuring Tape
• Drill
• Stud Finder
• Wood Bit
• Hammer
• Masonry Bit
• Security Torx Driver (implied by 'P' screw)

Project Overview

Follow these steps for installation:

1. Select TV Screws and Spacers
2. Select Spacers for Irregular TVs
3. Attach TV Brackets
4. Assemble Wall Plate
5. Mount Wall Plate Assembly
6. Hang TV
7. Level TV
8. Finalize Adjustments
9. Remove TV

IMPORTANT!: Please read this entire document before attempting assembly.

Step 1: Select TV Screws and Spacers

Selecting Screws: The back of your TV has 4 screw holes in a square or rectangular pattern. Kanto provides various screw sizes and lengths. This guide helps you select the right screws. You will only use 4 screws to attach your TV; the rest are not needed.

Selecting Spacers: Plastic spacers (I-K) are provided in 3 thicknesses. Use them to accommodate curved TVs, TVs with recessed mount holes, or protrusions. Spacers can also prevent screws from going too deep and damaging your TV. You may not need spacers for your TV.

Step 2: Select Spacers for Irregular TVs

Spacers can be used to provide clearance around protrusions on the back of your TV, or to accommodate a curved TV. You may need to use longer screws.

Step 3: Attach TV Brackets

WARNING: Do not lay the TV face down on its front. Use a wall or TV stand.

Attach the U-shaped TV brackets to the back of your TV using the selected screws (A-H) and optional spacers (I-K). Use whichever holes and slots work with your TV's VESA pattern.

Step 4: Assemble Wall Plate

Assemble the wall plate components as shown in the diagrams.

Step 5a: Mount Wall Plate Assembly (Wood Stud Wall)

Mounting Height: Depends on TV size, viewing position, and personal preference.

CAUTION: Make sure the supporting surface will support the load limits outlined in the caution on page two. Tighten lag bolts (M) until the wall plate is snug against the wall. Do not over-tighten. Each lag bolt must be located in the middle of a wood stud.

WARNING: Do not use concrete anchors in drywall or wood stud walls.

Step 5b: Mount Wall Plate Assembly (Concrete Wall)

Mounting Height: Depends on TV size, viewing position, and personal preference.

CAUTION: Make sure the concrete or brick wall is at least 4" thick. Ensure the anchor is seated completely flush with the concrete surface, even if there is another layer of material like drywall. If drywall is over 5/8" thick, custom lag bolts must be used. Concrete must be a minimum of 2000 psi in density.

WARNING: Do not use concrete anchors in drywall or wood stud walls.

Step 6: Hang TV

Lift the TV and attach it to the mounted wall plate. Ensure the brackets securely engage with the wall plate.

Step 7: Level TV

Adjust the TV to ensure it is level. Use the adjustment screws on the mount.

Step 8: Finalize Adjustments

Make final adjustments to the TV's position and tilt. The tilt range is approximately +12° to -2°.

Step 9: Remove TV

Follow these steps to safely remove the TV from the mount.

Kanto Product Showcase

Kanto offers a range of audio and video mounting solutions, including:

Speaker Systems:

• YU Series (YU Passive 5.25", YU Passive 4", YU, YU4, YU6)
• TUK Series
• SX Series (SX22, SX26)
• ST Series (ST34, ST34P, ST28, ST28P)
• H Series (H1, H2, HH)
• SE Series (SE6, SE4, SE2)
• S Series (S6, S4, S2)

Visit Kanto Online:

• kantoaudio.com
• Kanto Audio
• Kanto Solutions
• Kanto Living
• Kanto Solutions (YouTube)
• Kanto Audio (Instagram)

Limited Warranty

Kanto Living Inc. warrants its equipment to be free from defects in material for a period of 5 years from the date of shipment to the original purchaser. Kanto will, at its option, provide replacement parts or replace the equipment if it fails due to such defects and is notified within the warranty period with proof of purchase. Customers are responsible for return shipping costs, while Kanto covers reshipment costs for warranted items. Keep original packaging for shipping. This warranty is in lieu of all other warranties, expressed or implied.