Soundsation CHECKLINE Series Bi-Amped Coaxial Stage Monitors

Introduction

Welcome to the Soundsation CHECKLINE Series user manual. This guide provides comprehensive information for operating and maintaining your bi-amped coaxial stage monitors with on-board DSP.

Soundsation's mission is to satisfy the needs of musical instrument and professional audio users with products utilizing the latest technologies. We value your feedback for future improvements. Please visit www.soundsationmusic.com to share your opinions.

Read this manual carefully before using the instrument. Incorrect operation can cause damage to you and the unit.

Important Safety Symbols

⚡ [High Voltage]: Indicates hazardous live terminals. Risk of electric shock or death.

⚠️ [Caution]: Indicates specific components that must be replaced only with specified parts for safety.

⏚ [Grounding Terminal]: Protective grounding terminal.

~ [AC Voltage]: Alternating current/voltage.

⚠️ [Warning]: Precautions to prevent injury or death to the operator.

⚠️ [Caution]: Precautions to prevent damage to the apparatus.

Taking Care of Your Product

• Read and keep these instructions.
• Heed all warnings and follow all instructions.
• Water/Moisture: Protect from moisture and rain. Do not use near water.
• Heat: Locate away from heat sources.
• Ventilation: Do not block ventilation openings to prevent fire. Install according to manufacturer's instructions.
• Object and Liquid Entry: Keep objects and liquids out of the apparatus.
• Power Cord and Plug: Protect the cord from damage. Ensure the grounding pin is used for safety. Consult an electrician if the plug does not fit your outlet.
• Fuse: Use only the recommended fuse type. Ensure the unit is off and disconnected before replacing.
• Electrical Connection: Improper wiring may invalidate the warranty.
• Cleaning: Use a dry cloth. Do not use solvents.
• Servicing: Refer servicing to qualified personnel. Use only manufacturer-recommended accessories/parts.
• Warning: High sound pressure can damage hearing. Be careful with volume levels.

Package Content

Each unit has been tested and shipped in perfect operating condition. Carefully unpack and check contents:

• 1 Loudspeaker
• 1 Power cable
• 1 User manual

If damaged during transport, notify the shipper immediately and keep packing materials. Save original packaging for potential returns.

WARNING: Packaging box is not a toy! Keep out of reach of children!!!

Accessories

SOUNDSATION offers quality accessories for CHECKLINE stage monitors:

• CHECKLINE-10 BAG: Gig bag for CHECKLINE 10A (SKU Code #J128J)
• CHECKLINE-12 BAG: Gig bag for CHECKLINE 12A (SKU Code #J129J)
• CHECKLINE-15 BAG: Gig bag for CHECKLINE 15A (SKU Code #J130J)

Use genuine SOUNDSATION accessories and spare parts for best performance.

Overview

The CHECKLINE Coaxial Stage Monitor Series is designed for rental companies, sound engineers, and bands seeking robust, elegant, and practical stage tools without compromising sonic quality or performance.

Key features include:

• Full-range coaxial woofers.
• Bi-Amp module delivering 350W (Continuous) / 1000W (Program) power.
• Internal DSP for dynamics control, overload, and overheating protection.
• 2 factory presets (Flat, Monitor) and 5 user-defined presets.
• Versatile use as monitor, full-range speaker, front fill, or delayed speaker.
• High-performance and sonic clarity.
• 1000W (Peak) Class-D bi-amped power module.
• 48kHz/24-bit DSP with 2+5 EQ presets, 3-band EQ, Low-Cut, Delay (up to 100m).
• Dual-Band Peak/Overload/Thermal Limiter.
• Easy-to-use DSP Graphic Interface with LCD display and Single Encoder.
• Two combo inputs (XLR/6.3 jack with MIC/LINE switches).
• Stereo Line RCA Input (CHECKLINE 12" and 15" only).
• Two studio-quality microphone preamps.
• Rugged, texture-painted plywood enclosure.
• Sophisticated coaxial transducers.
• 90°x90° sound coverage.

Product Description

Dimensions and Weight

Diagrams showing Width, Height, Depth, and Ø36mm Pole Hole are present.

CHECKLINE 10A Front Panel

The front panel features:

1. ON/OFF Switch: Powers the speaker on/off.
2. AC MAINS: Power input connector for the supplied power cable. Ensure voltage compatibility (100-240Vac, 50/60 Hz +/- 10%).
3. AC LINK: Connector for powering other stage monitors to reduce cable clutter.
4. Input A and B: XLR + 1/4" Jack Combo connectors for balanced MIC/Line signals.
5. GAIN A and B Selectors: Adjust input gain for Microphone (+37dB) or Line (0dB) signals.

WARNING: Check gain selector position before connecting signals to prevent damage.

CHECKLINE 12A-15A Front Panel

The front panel features:

1. ON/OFF Switch: Powers the speaker on/off.
2. AC MAINS: Power input connector. Ensure voltage compatibility (100-240Vac, 50/60 Hz +/- 10%).
3. AC LINK: Connector for powering other stage monitors.
4. Mix Output: Balanced XLR output for connecting to other speakers or audio systems.
5. Loop C: Direct balanced XLR output from input C for daisy-chaining multiple monitors with the same signal.
6. GAIN B and C Selectors: Adjust input gain for Microphone (+37dB) or Line (0dB) signals.

WARNING: Check gain selector position before connecting signals to prevent damage.

7. Input B and C: XLR + 1/4" Jack Combo connectors for balanced MIC/Line signals.
8. Volume A, B, C: Adjusts input levels.
9. Input A: Stereo unbalanced RCA Line-level connectors.
10. LCD Display: Shows audio signal levels and DSP parameters.
11. Control Wheel: Adjusts Master Volume, DSP programming, and panel locking.

Cabling and First Setup

Mains Cable

Ensure the power wall socket voltage is 100-240Vac - 50/60 Hz (+/- 10%) before connecting. Disconnect the unit when switched off.

Note on AC Line-Cord: If the original cord is lost, use a three-pin plug with a ground pin. Wire correspondence: Brown (Live/L), Blue (Neutral/N), Yellow/Green (Earth).

ATTENTION: Always connect the earth terminal! Pay attention to your safety!

Installation should be approved by an expert before first use.

Signal Cables

Use appropriate, shielded, and undamaged cables. Damaged or incorrect cables can damage the system.

Balanced XLR Connectors: Pin 1: Ground/Shield, Pin 2: Hot (+), Pin 3: Cold (-). For unbalanced use, Pins 1 and 3 are jumped.

1/4" Jack TRS (Balanced): Used for headphones connection.

1/4" Jack TS (Unbalanced): Used for unbalanced signals.

RCA Connector (Unbalanced): For unbalanced equipment to balanced inputs, ensure ring and collar are connected together (or pins 1 & 3 for XLR).

DSP Operation

The CHECKLINE Series Stage Monitors feature a DSP audio processor for dynamics control, overload/overheating protection, frequency response adjustment, preset recall/creation, and delay up to 100 meters.

The DSP control panel has a graphic LCD display and a Push-to-Enter control wheel.

WARNING: Ensure correct input mode (MIC or LINE) is selected before powering on.

Turn all gain controllers to the left. Switch on the unit; the SOUNDSATION logo will appear during initialization.

The display will then show the home screen, indicating input levels (VU-Meter bars) and master volume.

Panel Locked: Press and hold the control wheel for over 3 seconds to lock/unlock the DSP panel.

Menu Navigation

Press the wheel to enter the menu. Rotate to scroll through pages and parameters. Selected parameters are displayed inverted.

To modify a parameter, select it, press the wheel, then rotate to adjust the value. Press again to confirm.

Note: The display returns to the Home Screen automatically after 6-7 seconds of inactivity.

DSP Parameters

• HI EQ: Adjusts high-frequency equalization (-12 dB to +12 dB).
• MID EQ/MID FREQ: Adjusts mid-frequency equalization (-12 dB to +12 dB) and frequency (70Hz to 12kHz).
• LOW EQ: Adjusts low-frequency equalization (-12 dB to +12 dB).
• PRESETS: Selects operating modes (FLAT, MONITOR).
• LOW CUT: Adjusts the High-Pass filter cutoff frequency (OFF, 80Hz, 100Hz, 120Hz, 150Hz) for use with subwoofers.
• DELAY: Sets delay time (OFF or 0.25 to 100 meters).
• LCD DIM: Controls LCD backlight (OFF = always on, ON = dims after 6 seconds).
• BRIGHT: Adjusts display brightness (0-10).
• CONTRAST: Adjusts display contrast (0-10).
• LOAD PRESET: Loads saved user presets (U1-U5).
• STORE PRESET: Saves current settings to user presets (U1-U5). Allows naming presets.
• FACTORY RESET: Resets the unit to factory settings. WARNING: This will delete all presets!
• INFO: Displays DSP firmware version (e.g., V1.2.0).
• EXIT: Exits DSP editing and returns to the main page.

Specifications

Note: Product specifications are subject to change without notice.

Optional Accessories are listed.

Warranty and Service

SOUNDSATION products have a limited two-year warranty from the date of purchase.

Not covered:

• Accessories supplied with the product.
• Improper use.
• Wear and tear.
• Modifications by user or third party.

SOUNDSATION will remedy faults by repair or exchange at their discretion. Defective parts become SOUNDSATION property.

Defective products under warranty can be returned to the local SOUNDSATION dealer with proof of purchase. For transit, use original packaging. Alternatively, send to SOUNDSATION SERVICE CENTER – Via Enzo Ferrari, 10 – 62017 Porto Recanati - Italy. An RMA number is required. Shipping costs are the owner's responsibility.

For more information, visit www.soundsationmusic.com.

Warning (EU/EEA)

♻️ [WEEE Symbol]: This symbol indicates the product must not be disposed of with household waste, according to the WEEE Directive and national law. It should be handed over to a designated collection point or authorized recycling site for electrical and electronic equipment.

Improper disposal can negatively impact the environment and human health due to hazardous substances. Proper disposal contributes to resource conservation.

Contact local authorities for information on collection points.