Altronix Home
User Manual for Altronix models including: HubWay8CDS UTP Passive Transceiver Hub 8 Channel, HubWay8CDS, UTP Passive Transceiver Hub 8 Channel, Transceiver Hub 8 Channel, Hub 8 Channel
Altronix HUBWAY8CDS | UTP Passive Transceiver Hub, 8 Channel
File Info : application/pdf, 8 Pages, 1.13MB
DocumentDocumentVideo · Data · Power HubWayCDS Series Passive UTP Transceiver Hub with Integral Camera Power Models Include: HubWay8CDS - UL Listed eight (8) Channel Passive UTP Transceiver Hub with Integral Camera Power HubWay82CDS - UL Listed eight (8) Channel Passive UTP Transceiver Hub with Integral Camera Power - Includes eight (8) UL Listed Accessory HubWayAv Video Balun/Combiners HubWay83CDS - UL Listed eight (8) Channel Passive UTP Transceiver Hub with Integral Camera Power - Includes eight (8) UL Listed Accessory HubWayDv Video Balun/Combiners Installation Guide Z1409 Rev. 070908 More than just power.TM Installing Company: _______________ Service Rep. Name: __________________________________ Address: _____________________________________________ Phone #: __________________ Overview: Altronix HubWay8CDS Passive UTP Transceiver Hub with Integral Camera Power transmits UTP video, RS422/ RS485 data and power over a single CAT-5 or higher structured cable. Unit provides 8 camera channels in a space saving 1U EIA 19" rack mount chassis which may be rack, wall or shelf mounted. Video transmission range is up to 750 ft. max. per channel. Units are compatible with AC and/or DC fixed or PTZ cameras when utilizing Altronix HubWayAv, HubWayAv2, HubWayDv or HubWayDvi Video Balun/Combiners. In addition, the unit features individually selectable 24VAC or 28VAC, PTC protected outputs with surge suppression. An optional HubSat4D Passive UTP Transceiver Hub with Integral Camera Power unit can be used as an accessory module to transmit video from up to 4 cameras over a single CAT-5 or higher structured cable back to the HubWay8CDS. In addition, the HubSat unit provides power to these cameras locally to eliminate the possibility of voltage drop associated with long cable runs. HubWay8CDS Specifications: Agency Listings: · UL Listed for Commercial CCTV Equipment (UL 2044). cUL Listed - CSA Standard C22.2 No.1-04, Audio, Video and Similar Equipment. Input: · 115VAC, 60Hz, 1.5A. Video: · Eight (8) channels of video over twisted pair up to 750 ft. · Eight (8) 75 Ohm video outputs. Data: · RS422/RS485 data inputs. Power: · Individually selectable 24VAC or 28VAC power outputs with OFF position. · Unit provides up to 1A max. per channel not to exceed a total of 5A (150VA) maximum current. · PTCs are rated @ 1A per channel. · Surge suppression. Visual Indicators: · AC input power indicator. · Eight (8) power LED indicators. Features: · Illuminated master power disconnect circuit breaker with manual reset. · IEC 320 - 3-wire grounded line cord (detachable). · Unit can be rack, wall or shelf mounted. · 1U rack mount chassis for use in standard EIA 19" rack. Accessories: · Video Balun/Combiners: - HubWayAv: for use with 24VAC cameras. - HubWayAv2: for use with 24VAC cameras. - HubWayDv: for use with 12VDC cameras. - HubWayDvi: for use with non-isolated 12VDC cameras. · Optional HubSat4D allows transmission of up to four (4) video signals over a single CAT-5 or higher structured cable. Additional Models: HubWay82CDS · HubWay8CDS with eight (8) UL Listed Accessory HubWayAv Video Balun/Combiners for 24VAC Cameras. HubWay83CDS · HubWay8CDS with eight (8) UL Listed Accessory HubWayDv Video Balun/Combiners for 12VDC Cameras. WARNING: To reduce the risk of fire or electric shock do not expose the unit to rain or moisture. This installation should be made by qualified service personnel and should conform to all local codes. - 2 - HubWay8CDS Installation Guide Installation Instructions: 1. Attach mounting brackets to HubWay unit for rack or wall mount installation (Figs. 6-7, pg. 8). Affix rubber pads to HubWay for shelf installation (Fig. 8, pg. 8). 2. Secure the unit in a rack, mount unit to a wall or place unit on a shelf as desired (unit should be spaced at least 3" from any video monitors). 3. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 5, pg. 7). 4. Plug the grounded AC line cord (included) into the IEC 320 connector of the HubWay8CDS unit (Fig. 1e, pg. 4). Insert the plug end of the line cord into a grounded AC receptacle. 5. Set voltage output selector switch of each camera channel for 24VAC or 28VAC (Fig. 1a, pg. 4). 6. Connect the BNC video outputs for HubWay8CDS Channels 1-8 to the corresponding video inputs on the head end equipment (DVR) (Fig. 1d, pg. 4). 7. Connect the RS422/RS485 output of the head end equipment (DVR) to the data input terminal block of the HubWay8CDS unit (polarity must be observed) (Fig. 1c, pg. 4). 8. Connect Video Balun/Combiner at camera 1 to the HubWay8CDS unit utilizing CAT-5 or higher structured cable. Plug the RJ45 connector at one end of the structured cable into the RJ45 jack marked [Channel 1] of the HubWay8CDS (Fig. 1g, pg. 4). Plug the RJ45 connector at the opposite end of the structured cable into the RJ45 jack of the Video Balun/Combiner located at camera 1. · For 24VAC cameras use Altronix model HubWayAv/HubWayAv2 Video Balun/Combiner (Figs. 2a, 2b, 2e, pg. 5). · For 12VDC cameras use Altronix model HubWayDv Video Balun/Combiner (Figs. 2c, 2d, pg. 5). · For non-isolated 12VDC cameras use Altronix model HubWayDvi Video Balun/Combiner (Figs. 2c, 2d, pg. 5). Repeat steps 6-9 for each additional camera (Channels 2-8). Note: When a particular camera exceeds the maximum distance for power transmission, a local external power source is required. Optionally, an Altronix HubSat Passive UTP Transceiver Hub with Integral Camera Power unit may be utilized (Fig. 4a, pg. 6). The combined total cable distance must not exceed 750 ft. for video transmission between the HubWay8CDS and each camera routed through the HubSat4D unit. 9. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 5, pg. 7) and measure the output voltage at the power output of each Video Balun/Combiner (Figs. 2b, 2d, pg. 5) before powering each camera to ensure proper operation and avoid possible damage. · HubWayAv/HubWayAv2 - Terminals marked [AC POWER] (Figs. 2a, 2b, 2e, pg. 5). · HubWayDv/HubWayDvi - Terminals marked [ 12VDC +] (Figs. 2c, 2d, pg. 5). 10. Set illuminated master power disconnect circuit breaker to the (OFF) position to make the final connections (Fig. 5, pg. 7). 11. Connect the power outputs of the HubWayAv, HubWayAv2, HubWayAv2, HubWayDv or HubWayDvi Video Balun/Combiners to the power inputs of the cameras (Figs. 2a-2e, pg. 5). Polarity must be observed. 12. Connect the terminals marked [+ DATA ] of the HubWayAv, HubWayAv2, HubWayDv or HubWayDvi Video Balun/Combiners to the data terminals of the cameras for PTZ control (Figs. 2a-2e, pg. 5). Polarity must be observed. When using fixed cameras disregard this step. 13. Connect the BNC connectors of the HubWayAv, HubWayAv2, HubWayDv or HubWayDvi Video Balun/ Combiners to the BNC video outputs of the cameras (Figs. 2a-2e, pg. 5). 14. Upon completion of wiring set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 5, pg. 7). 15. The power LEDs (Red) located on the front of the HubWay8CDS will illuminate when AC power is present (Fig. 1c, pg. 4). Note: If any of these LEDs are not illuminated either a voltage output selector switch is in the OFF position or the PTC is tripped for that channel. To reset the PTC: 1. Set the voltage output selector switch for that corresponding channel to the OFF position. Switch must remain in the OFF position for approximately 2 minutes in order for the PTC to reset. 2. Eliminate the trouble condition (short circuit or overload). 3. Set the voltage output selector switch for 24VAC or 28VAC (Fig. 1a, pg. 4). 16. AC LEDs (Green) of the HubWayAv or DC LEDs (Red) of the HubWayDv/HubWayDvi Video Balun/ Combiners will illuminate indicating power is present at the cameras (Fig. 2b, 2d, pg. 5). HubWay8CDS Installation Guide - 3 - - 4 - Fig. 1 1a - Output voltage switches: Selects 24VAC/28VAC/OFF for each output. Top View + -- Data input from Head End Equipment (DVR). 1c - Data: Removable terminal blocks for RS422/ RS485 input from head end equipment (DVR) for PTZ control. Rear 1b - LED(s) 1-8: Power indicators. -- DATA + 24VAC OFF 28VAC 1-8 CH 5-8 8 7 6 5 CH 1-4 4 3 2 1 1f - Channels 1-4 & Channels 5-8: Links HubSat units enabling video transmission of up to four (4) cameras over a single CAT-5 structured cable. 1d - BNC Connector: Video outputs to head end equipment (DVR). 1e - IEC 320 Connector: 115VAC, 60Hz (grounded line cord included). 8 7 6 5 4 3 2 1 AC POWER 1g - Channels 1-8: CAT-5 or higher structured cable to Video/Balun Combiners at cameras 1-8. When linking HubWay UTP Transceiver Hubs to HubSat Remote Accessory Modules, any of these jacks will facilitate data transmission for PTZ control. HubWay8CDS Installation Guide HubWayAv, HubWayAv2, HubWayDv, and HubWayDvi Video Balun/Combiners: Altronix Model Number Input Voltage from HubWay Unit Output Voltage to Camera HubWayAv *24VAC/28VAC *24VAC/28VAC HubWayAv2 *24VAC/28VAC *24VAC/28VAC HubWayDv *24VAC/28VAC 12VDC *Based on camera load and structured cable length. Camera Type *24VAC/28VAC *24VAC/28VAC 12VDC cameras Power LED Green N/A Red Fig. 2 Fig. 2a Fig. 2b VIDEO HubWayAv VIDEO BALUN/COMBINER CAT5 AC +DATA-- POWER RJ45 Jack Wire Connectors Fig. 2c Fig. 2d VIDEO HubWayDv VIDEO BALUN/COMBINER CAT5 +DATA-- -- 12VDC+ * Also Available as: HubWayDvi Video Balun/ Combiner for non-isolated 12VDC cameras RJ45 Jack Wire Connectors To BNC Connector of Camera Structured Cable from HubWay8CD or HubWay16CD Fig. 2e - HubWayAV2 Cat5 back to HubWay or HubSat Green Power LED AC Power to Camera -- Data to + Camera To BNC Connector of Camera Structured Cable from HubWay8CD or HubWay16CD Power to Camera Data to Camera Red Power LED + 12VDC Power -- to Camera -- Data to + Camera HubWayAv/HubWayAv2 passes AC voltage from pins 4, 5, 7, 8 to terminals marked [AC Power] (Fig. 3, pg. 5). Video from Camera HubWayDv/HubWayDvi converts AC voltage to DC voltage from pins 4, 5, 7, 8 to terminals marked [ 12VDC +] (Fig. 3, pg. 5). Fig. 3 - CAT-5 Structured Cable Wiring Color Codes and PIN Configurations 1 - White/Orange [VIDEO +] 2 - Orange [VIDEO ] 3 - White/Green [DATA +] 4 - Blue [AC 1] 5 - White/Blue [AC 2] 6 - Green [DATA ] 7 - White/Brown [AC 2] 8 - Brown [AC 1] HubWay8CDS Installation Guide - 5 - HubWay8CDS Installation Guide - 6 - Fig. 4 Typical Applications: Head End Equipment (DVR) Monitor RS485 Video Data -- DATA + 24VAC OFF 28VAC 1-8 CH 5-8 8 7 6 5 CH 1-4 4 3 2 1 8 7 6 5 4 3 2 1 AC POWER IEC 320 Connector 115VAC 60 Hz. Video Data Power Four (4) Video signals on a single CAT-5 CAT-5 Data (CAT-5) CAT-5 Video Data Power HubWayDv/Dvi PTZ Camera Video Balun Combiner Video Power CAT-5 HubWayDv/Dvi Fixed Camera Video Balun Combiner 24VAC/28VAC Camera Power Provided by HubSat4D HubWayAv Video Balun Combiner PTZ Camera Power Video (Coax) 115VAC Input, 50/60Hz Fig. 4a - Optional hookup utilizing HubSat4D. Fixed Camera CAT-5 Video Power CAT-5 Video Power Max. video 750 ft. HubWayAv Fixed Camera Video Balun Combiner HubWayDv/Dvi Fixed Camera Video Balun Combiner CAT-5 Video Data Power Outdoor PTZ Camera HubWayAv PTZ Camera Video Balun Combiner Outdoor NEMA Rated Power Supply CAT-5 Video Data HubWayAv or HubWayDv/Dvi Video Balun Combiner Power 115VAC Input, 50/60Hz The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of an insulated DANGEROUS VOLTAGE within the product's enclosure that may be of sufficient magnitude to constitute an electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. CAUTION: To reduce the risk of electric shock do not open enclosure. There are no user serviceable parts inside. Refer servicing to qualified service personnel. 1U EIA 19" Rack Mount Chassis Dimensions (H x W x D approximate): 1.625" x 19.125" x 8.5" (41.3mm x 486mm x 216mm) -- DATA + 24VAC OFF 28VAC 1-8 CH 5-8 8 7 6 5 CH 1-4 4 3 2 1 8 7 6 5 4 3 2 1 Rear AC POWER 1.625"(41.3mm) 17.625" (447.7mm) 8.5" (216mm) Top and Bottom 0.75" (19.1mm) Front 19.125" (486mm) Fig. 5 Illuminated master power disconnect circuit breaker: · OFF position Circuit breaker tripped Switch not illuminated. · RESET (ON) position Switch illuminated. HubWay8CDS Installation Guide - 7 - Mounting Options: Rack Mount Installation 1. Remove factory installed screws from both sides of the rack chassis (Fig. 6a). 2. Install mounting brackets (A) on the left and right side of rack chassis using the two (2) flat head screws (B) (included) (Fig. 6b). 3. Place unit into desired EIA 19" rack position and secure with mounting screws (not included) (Fig. 6c). Fig. 6 Fig. 6a Fig. 6b Fig. 6c Top Front Left Top Top Front Left Remove B A Front Left Wall Mount Installation 1. Install mounting brackets (A) on the left and right side of rack chassis using two (2) flat head screws (B) (included) (Fig. 7a). 2. Place unit at desired location and secure with mounting screws (not included) (Fig. 7b). Caution: It is necessary to make sure mounting screws are securely fastened to a beam when installing. Fig. 7 Fig. 7a Fig. 7b B A Shelf Installation 1. Position and affix rubber pads (C) (included) at Mounting Hardware (Included): each corner on the bottom of the unit (Fig. 8). 2. Place unit in desired location. Fig. 8 A Two (2) mounting brackets Left Side B Six (6) flat head screws for mounting brackets. C Rubber Pad C Four (4) rubber pads. Altronix is not responsible for any typographical errors. 140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056 website: www.altronix.com | e-mail: info@altronix.com | Lifetime Warranty IIHubWay8CDS K19U MEMBER - 8 - HubWay8CDS Installation Guide