Installation Guide for Signature Streetscapes models including: Gigabit ETH HAT Light, Gigabit ETH HAT, Light
– Signature Streetscapes
Product Catalogs & Resources | Signature Streetscapes
Decorative Street Sign Blades | Custom Metal Street Signs
File Info : application/pdf, 2 Pages, 1.26MB
DocumentDocumentCLASSIC BLADE TRIM INSTALLATION GUIDE TOLL FREE: 1-800-705-1446 WE CAN HELP! TOOLS REQUIRED MOUNTING TEMPLATE - Mounting Template (Provided) - Mounting Hardware Packet (Provided) - 3/8" Drill Bit - 1/2" Wrenches - Permanent Marker - Tape Measure - Hammer - Center Punch - Local Sign Ordinance Height and Location Requirements 5/16-18 TAPPED HOLE INSTRUCTIONS 1) Hole location for sign installation is determined by the height requirement and orientation of the completed installation. 2) Measure from the top of post to the first hole location & mark w/ permanent marker. 3) Use the mounting template to locate and mark the bottom hole location. 4) Use hammer and center punch to dimple the hole locations (if necessary). 5) Use 3/8" drill bit to drill clearance hole. 6) Repeat steps 1-5 to drill holes on opposite side of post 7) Repeat steps 1-5 to drill holes on each side of post for second street sign 8) Mount Classic Blade Trim to post using 5/16-18 stainless steel bolts & washers (provided). Cast aluminum bracket has (2) 5/16-18 tapped holes to accept thru-bolts. NOTE: Mounting bracket will seat best to fluted post when mounting holes are drilled center in the recessed flute. POST PROFILE HARDWARE REQUIRED ATTACHMENT FOR 3" ROUND FLUTED, SMOOTH OR SQUARE POST (2) 5/16-18 X 4" stainless steel hex bolts (4) 5/16" stainless steel flat washers (2) 5/16" stainless steel split lock washers ATTACHMENT FOR 4" ROUND FLUTED, SMOOTH OR SQUARE POST (2) 5/16-18 X 5" stainless steel hex bolts (4) 5/16" stainless steel flat washers (2) 5/16" stainless steel split lock washers COMPLETED SIGN INSTALLATION CLASSIC BLADE TRIM Willow Wick Dr CLASSIC BLADE TRIM WITH BELLFLOWER SCROLL Willow Wick Dr NOTE: Sign face orientation and direction is a key component of the installation process. It is important to plan ahead to ensure that each sign may be viewed properly from each direction. It will be necessary to offset the height of two street blades mounted perpendicular to each other to avoid interference of the mounting hardware. IMPORTANT: Hardware only included if purchased with post or if specified at time of order. signaturestreetscapes.com 1-800-705-1446 CLASSIC PADDLE TRIM INSTALLATION GUIDE TOLL FREE: 1-800-705-1446 WE CAN HELP! TOOLS REQUIRED MOUNTING TEMPLATE - Mounting Template (Provided) - Mounting Hardware Packet (Provided) - 3/8" Drill Bit - 1/2" Wrenches - Permanent Marker - Tape Measure - Hammer - Center Punch - Local Sign Ordinance Height and Location Requirements INSTRUCTIONS 3/8" THRU HOLE 1) Hole location for sign installation is determined by the height requirement and orientation of the completed installation. 2) Measure from the top of post to the first hole location & mark w/ permanent marker. 3) Use the mounting template to locate and mark the bottom hole location. 4) Use hammer and center punch to dimple the hole locations (if necessary). 5) Use 3/8" drill bit to drill clearance hole. 6) Repeat steps 1-5 to drill holes on opposite side of post 7) Repeat steps 1-5 to drill holes on each side of post for second street sign 8) Mount Paddle Trim to post using 5/16-18 stainless steel bolts & washers (provided). NOTE: Brackets are pre-drilled with 3/8" holes ONLY when mounting 180 degree from classic blade trims. As specified in drawings. If not specified, brackets will come standard with 5/16-18 tapped holes Cast aluminum bracket has (2) 5/16-18 tapped holes to accept thru-bolts. POST PROFILE NOTE: Mounting bracket will seat best to fluted post when mounting holes are drilled center in the recessed flute. HARDWARE REQUIRED ATTACHMENT FOR 3" ROUND FLUTED, SMOOTH OR SQUARE POST (2) 5/16-18 X 4" stainless steel hex bolts (4) 5/16" stainless steel flat washers (2) 5/16" stainless steel split lock washers ATTACHMENT FOR 4" ROUND FLUTED, SMOOTH OR SQUARE POST (2) 5/16-18 X 5" stainless steel hex bolts (4) 5/16" stainless steel flat washers (2) 5/16" stainless steel split lock washers COMPLETED SIGN INSTALLATION CLASSIC BLADE TRIM Willow Wick Dr CLASSIC BLADE TRIM WITH BELLFLOWER SCROLL Willow Wick Dr NOTE: Sign face orientation and direction is a key component of the installation process. It is important to plan ahead to ensure that each sign may be viewed properly from each direction. It will be necessary to offset the height of two street blades mounted perpendicular to each other to avoid interference of the mounting hardware. IMPORTANT: Hardware only included if purchased with post or if specified at time of order. signaturestreetscapes.com 1-800-705-1446