Instructions for Casambi models including: SRP-CA9105N Dimmable LED Driver, SRP-CA9105N, Dimmable LED Driver, LED Driver
Casambi dimmable LED driver, works with Casambi network. • 2 channels dimmable LED driver. Max. output power 65W. • 500-1500mA current selectable via NFC ...
2 days ago — 0/50/60Hz. Input. Rated Power. Output. Current. DC Voltage. LED Channel. Current Accuracy. ±3%( ±1%@Certain full load) @ full load. > 0.97 @ 230VAC Full load*.
Casambi 65W 2CH NFC Enabled LED Driver(Constant Current) IS ------ THOMAS SAMUEL THOMAS SAMUEL R-xxxxxxxx Important: Read All Instructions Prior to Installation Function introduction LED OUTPUT LED Output WW- CW- AC Push Input AC/DC power input Casambi Dimmable Driver PUSH L PUSH DIM PUSH L NN INPUT ACL/ DC+ ACN/ DC- Product Data LED Channel 2 DC Voltage 6-54V, Max. 60V Output Input Control Current 500-1500mA via NFC tool; Min.current gear lower to 0.1mA, default 1050mA Current Accuracy ±3%( ±1%@Certain full load) @ full load Rated Power Voltage Range Absolute Voltage Range Frequency Range Power Factor (Typ.) Total Harmonic Distortion Efficiency (Typ.) AC Current (Typ.) Inrush Current (Typ.) Leakage Current Standby Power Consumption Anti Surge Dimming Interface Max. 65W 220-240VAC/220-240VDC 196-264VAC/196-264VDC 0/50/60Hz > 0.97 @ 230VAC Full load* THD 10% (@ full load / 230VAC)* 88% @ 230VAC full load* 0.4A Max. Max. 9.68A at 230VAC; 70s duration < 5mA /230VAC 0.5W L-N:2KV Casambi Dimming Range 0.01%-100%@ Max current Dimming Method Amplitude/CCR dimming Dimming Curve Linear/ Logarithmic optional Short Circuit Yes, remove the fault conditions and re-power the device. Protection Over Current Yes, remove the fault conditions and re-power the device. Over Temperature Yes, remove the fault conditions and re-power the device. Working Temp. -25 ~ +45 Max. Case Temp. Environment Working Humidity Tc=85 10% ~ 95% RH non-condensing Storage Temp. & Humidity -40 ~ +80, 10% ~ 95% RH Safety Standards EN61347-1, EN61347-2-13, GB/T 19510.1-2023, GB/T 19510.213-2023 Safety & EMC Withstand Voltage I/P-O/P: 3.75KVAC Isolation Resistance I/P-O/P: 100M Ohms / 500VDC / 25 / 70% RH EMC Emission EN55015, EN61000-3-2, EN61000-3-3, GB 17625.1-2022, GB/T 17743-2021 EMC Immunity EN61547, EN61000-4-2,3,4,5,6,8,11 Others MTBF Dimension 191350H, MIL-HDBK-217F @ 230VAC full load and 25 ambient temperature 123.9x78.8x30mm (L*W*H) Warranty 5 Years *: PF/THD/Eff shall be different per different testing setup and equipment. · Casambi dimmable LED driver, works with Casambi network · 2 channels dimmable LED driver. Max. output power 65W · 500-1500mA current selectable via NFC program tool. Min.current gear lower to 0.1mA · Class power supply, full isolated plastic case · High power factor and efficiency · ON/OFF, Dimming and Tunable White control · Amplitude/CCR dimming, smooth and deep dimming · IP20 rating, suitable for indoor LED lighting applications · 5 years warranty Safety & Warnings · DO NOT install with power applied to the device. · DO NOT expose the device to moisture. Operation Configuration via NFC tool Note: 1) Please do not power on the device during the whole programming process. 2) Please make sure your phone has NFC function and enable it. 3) If you can't download the app, please contact us. Step 1: Install SR NFC Tool app on your phone(search SR NFC Tool from Apple Store or Google Play), and add the device following the app instructions. Step 3: After setting, write all configurations to the device. Step 2: Unlock the device and set the wanted parameters. Locked Unlocked Parameters explained: Target Current Setting 0.1mA adjustment for each current gear. Wiring Diagram Application 1Without PUSH LED OUTPUT CCT LED WWCW- Casambi Dimmable Driver PUSH L PUSH DIM PUSH L NN INPUT ACL/ DC+ ACN/ DC- Current Compensation: It is realized by setting different levels of current compensation for NFC drivers in different power segments and different currents of the driver. It is a method to realize fine lighting control for most constant-current luminaries in the market (such as downlight, spotlight, panel light, etc). LN Note: Avaliable with 3-wire CCT luminaries as well Application 2With PUSH LED OUTPUT CCT LED WWCW- Casambi Dimmable Driver PUSH L PUSH DIM PUSH L NN INPUT ACL/ DC+ ACN/ DC- AC PUSH SWITCH Note: Avaliable with 3-wire CCT luminaries as well LN Push Dim 1) Short press to switch on or off. 2) Long press to dim up or dim down. Product Dimension Operating window Output voltage [V] 60 ULED (max), V 54 45 36 ULED (min), V 27 18 9 0 0,10 0,30 0,50 0,70 0,90 1,10 1,30 1,50 1,70 Output current [A] Dimming Curve Note: Test data under 1500mA gear Driver Performance 35%/ 46%/ 57%/ 70%/ 80%/ 92%/ 100% Note: Test data under 1500mA gear Driver Performance 35%/ 46%/ 57%/ 70%/ 80%/ 92%/ 100% Note: Test data under 1500mA gear Driver Performance 6%/ 9%/ 11%/ 13%/ 17%/ 19%/ 26%/ 32%/ 43%/ 53%/ 64%/ 74%/ 85%/ 98% Note: Test data under 1500mA gear Expected Lifetime Module Number Output current Ta SRP-CA9105N-65CC500-1500 500 1500 mA Tc 30 °C 50 °C 40 °C 60 °C 45 °C 68 °C SRP-CA9105N-65CCT500-1500 500 1500 mA Lifetime > 100,000 h > 100,000 h > 100,000 h 85 °C > 40,000 h The LED driver is designed for a lifetime stated above under reference conditions. The relation of tc to ta temperature depends also on the luminaire design. MCB Load Quantity Module Number Ipeak Twidth Max.quantity of LED Driver per MCB B10 B13 B16 B20 B25 C10 C13 C16 C20 C25 D10 D13 D16 D20 D25 SRP-CA9105N-65CC500-1500 9.68A 70s 15 20 24 30 38 20 26 32 40 50 22 29 36 45 57 SRP-CA9105N-65CCT500-1500 9.68A 70s 15 20 24 30 38 20 26 32 40 50 22 29 36 45 57 I (A) Ipeak ½ Ipeak t T (ms) Note: 1.Those MCB parameters are based on ABB S200 series circuit breakers. 2.For different brands and models of miniature circuit breakers, the quantity of drivers will have difference. 3.Please do not exceed the above-mentioned quantity during on-site installation, and the specific load quantity shall be subject to on-site installation. 4.When the installation environment temperature of MCBs exceeds 30°C or when multiple MCBs are installed side by side, the number of mounted drives will be reduced, which requires recalculation. 5.Type C MCB's are strongly recommended to use with LED lightingCorel PDF Engine Version 24.3.0.571 CorelDRAW 2022