Manual-Hub.com - Free English product PDF Documents!
User Manual for AVTRONICS models including: AVT-QUAD1 Microphone Wireless Systems, AVT-QUAD1, Microphone Wireless Systems, Wireless Systems
AVTRONICS AVT-QUAD1 (01) PDF MANUAL - MANUAL-HUB.COM
AVTRONICS AVT-QUAD1 (01) - Google Drive
File Info : application/pdf, 8 Pages, 2.45MB
DocumentDocument4 Microphone Wireless Systems Sistema de 4 micrófonos inalámbricos USERS MANUAL for Professional Series Models: > AVT-QUAD1 > AVT-QUAD2 > AVT-QUAD2B (AVT-4BP1 and AVT-4BP2 Beltpack Transmitters) Please read and keep for future reference. Distributed by: www.avtronicsworld.com https://manual-hub.com/ FCC INFORMATION AVT-QUAD1R and AVT-QUAD2R Receiver: TRANSMITTER SPECIFICS AVT-QUAD1 and AVT-4BP1 Handheld Transmitters: Channel A (Purple) 696.65 MHz Channel B (Yellow) 693.65 MHz Channel C (Pink) 631.75 MHz Channel D (Gray) 625.15 MHz FCC ID: Y3I-AVTQUADHH8 FCC ID: Y3I-AVTQUADHH7 FCC ID: Y3I-AVTQUADHH6 FCC ID: Y3I-AVTQUADHH5 Beltpack Transmitters: Channel A (Purple) 696.65 MHz Channel B (Yellow) 693.65 MHz Channel C (Pink) 631.75 MHz Channel D (Gray) 625.15 MHz FCC ID: Y3I-AVTQUADBP8 FCC ID: Y3I-AVTQUADBP7 FCC ID: Y3I-AVTQUADBP6 FCC ID: Y3I-AVTQUADBP5 AVT-QUAD2, AVT-QUAD2B and AVT-4BP2 Handheld Transmitters: Channel A (Red) 697.85 MHz FCC ID: Y3I-AVTQUADHH4 Channel B (Green) 680.45 MHz FCC ID: Y3I-AVTQUADHH3 Channel C (Blue) 621.55 MHz FCC ID: Y3I-AVTQUADHH2 Channel D (Orange) 619.15 MHz FCC ID: Y3I-AVTQUADHH1 Beltpack Transmitters: Channel A (Red) 697.85 MHz Channel B (Green) 680.45 MHz Channel C (Blue) 621.55 MHz Channel D (Orange) 619.15 MHz FCC ID: Y3I-AVTQUADBP4 FCC ID: Y3I-AVTQUADBP3 FCC ID: Y3I-AVTQUADBP2 FCC ID: Y3I-AVTQUADBP1 * * * CONSUMER ALERT * * * Most users do not need a license to operate this wireless microphone system. Nevertheless, operating this microphone system without a license is subject to certain restrictions: the system may not cause harmful interference; it must operate at a low power level (not in excess of 50 milliwatts); and it has no protection from interference received from any other device. Purchasers should also be aware that the FCC is currently evaluating use of wireless microphone systems, and these rules are subject to change. For more information, call the FCC at 1-888-CALL-FCC (TTY: 1-888-TELL-FCC) or visit the FCC's wireless microphone website at www.fcc.gov/cgb/wirelessmicrophones. NOTE: The manufacturer, distributor, and supplier is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment. 2 https://manual-hub.com/ Congratulations on purchasing a fine wireless microphone system from AVTronics. This product should give you trouble free service throughout it's life. We trust you will enjoy it's performance. FEATURES AND SPECIFICATIONS LIST > Use up to 4 wireless microphones at once (8 with an additional system to use 2 systems use separate frequency groups such as AVT-QUAD1 and AVT-QUAD2 or AVT-QUAD2B) > Far reaching working distance: 200 feet > Reliable sturdy construction > Operates on 4 single channel fixed frequencies (UHF 600MHz band) > Carrier wave stability: 10PPM > Sensitivity: -105dB @ sinad = 12dB > S/N Ratio: >105dB (virtually eliminates distortion) > Great frequency response: 50Hz~18KHz > Squelch control: dual-squelch circuit eliminates static and stray signals > 4 individual volume controls > Max. output level: balanced (0 400mv), unbalanced (0 200mv) > Power supply: external DC power supply, 0.8A, 12~18V DC > Output connectors: 4 XLR balanced, 1 mixed unbalanced 1/4" TRS > Requires 2 AA batteries for each transmitter > Compact size: 16.5"(L) x 1.8"(H) x 9.8"(D) (approximate dimensions) > Lightweight: (approx.) 13.2 lbs for receiver and 4 microphones in carton AVAILABLE MODELS AVT-QUAD1 Comes with 4 handheld microphones, 1 receiver, and power cord. Frequency group 1. AVT-QUAD2 Comes with 4 handheld microphones, 1 receiver, and power cord. Frequency group 2. AVT-QUAD2B Comes with 3 handheld microphones, 1 beltpack and lavalier mic, 1 receiver, and power cord. Frequency group 2. AVT-4BP1 Comes with 4 beltpacks and lavalier mics. Frequency group 1. AVT-4BP2 Comes with 4 beltpacks and lavalier mics. Frequency group 2. Optional Accessories: To add optional accessories such as a pack of 4 beltpacks or a second system go to www.avtronicsworld.com to find a dealer. https://manual-hub.com/ 3 HELPFUL DIAGRAMS FRONT Switch ( ) Botón de Encendido Volume Control ( ) Control de Volumén Volume Control ( ) Control de Volumén Volume Control ( ) Control de Volumén Volume Control ( ) Control de Volumén BACK (Actual frequencies will vary by model) Channel D XLR Output Channel C Channel B XLR Output XLR Output (Canales de las Salidas XLR) Channel A Mixed 1/4" Power Cord XLR Output TRS Output Input ( ) ( ) Mezcla de Entrada Salida Cable de Cable de Energía Opening the device may void your warranty. Do not dispose of this device by putting in the trash. 4 https://manual-hub.com/ RECEIVER BELTPACK On/Off Switch ( ) Botón de Encendido On/Off Switch ( ) Botón de Encendido color coded by frequency ( ) codigo de color de frecuencia color coded by frequency ( ) codigo de color de frecuencia CAUTION! To lower the risk of potentially harmful electric shocks please do not perform any of the following procedures: > Do not disassemble, remove screws, or otherwise in any way open the enclosure. > Keep receiver and transmitters away from water including rain and moisture. > Make sure there are no breaks in the A/C power cable. > Make sure the switch is to the off position when you turn on the unit. > Do not use this device in the rain, swimming pools or in moist damp environments. PRECAUCIÓN Para disminuir el riesgo potencial de un golpe de corriente peligroso, por favor no lleve a cabo ninguno de los siguientes procedimientos: > No desmonte ó remueva tornillos en otras palabras, no abra por ninguna razón. > Mantenga el recibidor y el transmisor lejos de agua incluyendo lluvia ó humedad. > Asegurese que no existen roturas ó averías en el cable de corriente A/C. > Asegurese que el interruptor está apagado cuando usted encienda la unidad. > No use este artefacto bajo la lluvia, en piscinas ó en ambientes húmedos. https://manual-hub.com/ 5 Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 GETTING STARTED Verify that all equipment including the sound system is turned off. Attach power supply cord to receiver. Make sure you have batteries in each transmitter that you plan to use. Plug power supply cord from receiver into the wall. Plug receiver into sound system. Do this by either plugging in each channel using the XLR outputs on the back of the receiver (each channel requires one XLR cable) or by connecting one 1/4" cable to the sound board. Note: If you want the sound technician to be able to adjust each channel individually on your mixer, such as EQ, volume, and auxiliary send, you must use the XLR outputs, not the 1/4" output. Turn the channel volume controls on the receiver all the way up and mix independently on your mixer. If you use the 1/4" output you must adjust (mix) your volume levels on the front of your receiver. Turn on receiver. Turn on transmitters. Adjust individual volume controls to desired levels. TROUBLE SHOOTING PROBLEM POSSIBLE SOLUTION The receiver has no power. Check to make sure the power cord is plugged in and the switch is put to the "on" position. Transmitter has no power. Make sure the switch has been put to the "on" position. If the unit is still not working then check the batteries in the transmitter. Each unit requires 2 AA batteries. The volume of each microphone is not at the the same level coming through the sound board. Check to make sure the volume knobs on the receiver are all turned to the same position or all the way on. The sound is coming through on the same channel for all 4 microphones and as a result cannot be adjusted individually. Use 4 individual XLR cables to plug into the sound board instead of the 1/4"cable. Feedback The microphone user may be too close to a speaker or stage monitor while the microphone is in use. 6 https://manual-hub.com/ Paso 1 Paso 2 Paso 3 Paso 4 Paso 5 Paso 6 Paso 7 Paso 8 CÓMO CONECTAR EL EQUIPO Verifique que todo el equipo incluyendo el sistema de sonido este apagado. Conecte el cable del suplidor de energía al recibidor. Asegurese que tiene baterías para cada transmisor que usted se proponga usar. Conecte el suplidor de energía del recibidor a la pared. Conecte el recibidor al sistema de sonido. Puede hacer la connección de dos formas: Puede conectar cada canal utilizando las salidas XLR en la parte de atrás del recibidor (cada canal requiere un cable XLR) ó puede conectar un cable de 1/4" al sonido de la consola de sonido. Nota: Si usted quiere que su técnico de sonido pueda ajustar cada canal individualmente en su mezcladora de sonido, como el EQ, volumen ó auxiliares, usted debe usar las salidas XLR, no la salida de 1/4". De otra manera, suba hasta el final los controles de sonido, todo el volumen y mezcle independientemente en su mezcladora. Si usted usa la salida de 1/4", usted debe ajustar en su consola de sonido el volumen en el frente de su recibidor. Encienda el recibidor. Encienda los transmisores. Ajuste los controles de volumen para los niveles de sonido deseados. LOCALIZACIÓN Y SOLUCIÓN DE PROBLEMAS PROBLEMA POSIBLES SOLUCIONES El recibidor no tiene corriente. Asegurate que el cable de corriente está conectado y el interruptor está activado. El transmisor no tiene corriente. Asegurase que el interruptor este en la posición de activado. Si la unidad sigue sin trabajar entoces coteje las baterías del transmisor. Cada uno requiere 2 baterias doble A. El volumen de cada micrófono no está en el mismo nivel de sonido que viene de la consola de sonido. Asegurase de los botones de volumen en el recibidor estén todos en la misma posición ó todos subidos hasta el final. El sonido está llegando a travéz del mismo canal para los 4 micrófonos y como resultado no pueden ser ajustados individualmente. Usa 4 cables XRL individuales para conectarlos en consola de sonido en vez de el cable de 1/4". Interferencia en el sistema. El que este usando el micrófono puede estar muy cerca de alguna bocina o de los monitores de piso. https://manual-hub.com/ 7 www.avtronicsworld.com Made in China https://manual-hub.com/