DALI ECO BT RTC Control
DALI control unit with Bluetooth Low Energy interface
Product Overview
The DALI ECO BT RTC control unit is designed for luminaire integration, offering Bluetooth Low Energy connectivity. It is engineered in Germany and manufactured in Hungary.
Technical Specifications
- VAC: 220-240V; 50/60 Hz
- Power (P): 0.3 - 3W
- Ambient Temperature (ta): -20...+60 °C
- DALI Control Interface: DA+ / DA- / 15VDC / max. 300m total wire length
- Push Button Interface: max. total wire length PB1: 50m; PB2: 5m
- Wireless Interface: Bluetooth® 4.0 / Connectivity range: ≤ 15m
- Type of Protection: IP20
- Max. DALI Load: 32 ECG + 4 OSRAM DALI Sensors or OSRAM DALI Push button couplers; 96 mA
- Allowed Leads Diameter: 0.5 - 1.5 mm²
- Time Switch with Energy Storage: 72h buffer in case of mains power failure (charging time min. 24h mains operation)
Dimensions
The unit measures approximately 108 mm (length) x 21 mm (width) x 30 mm (height).
App Integration
Configuration and control are managed via dedicated smartphone applications:
- OSRAM BT CONFIG: For configuration and control.
- OSRAM BT CONTROL: For control functions.
Applications are available for iOS and Android smart phones.
Mounting and Safety Information
The DALI ECO BT RTC control unit is designed exclusively for luminaire integration. Independent installation, such as ceiling integration, is possible using the ECO CI KIT (Art. Nr. 4008321392091).
Recommended Cable Types for Independent Mounting:
- DALI + mains voltage: 1x NYM 5x1.5mm² or 1 x H05VV 5x1.5mm².
- External push button: 1x NYM 3x1.5mm² or 1 x H05VV 3x1.5mm².
Important Safety Notes:
- The push button and DALI interfaces provide basic electrical insulation. Connecting to external voltage, especially mains voltage, will destroy the unit.
- Presence or daylight-dependent operation requires connection to an OSRAM DALI sensor. Please contact your local sales representative for an overview of OSRAM DALI sensors.
- Do not place mains voltage or LED supply wires within or close to the indicated area.
- Ensure recommended minimal distance to metal parts.
- Proper placement of the integrated radio transmitter antenna is advised for correct radio connectivity.
- Install the 820 Ω / 5% / 1/4W resistance only inside the luminaire.
- The controller can be abutted against normally flammable materials, including building insulation, and can be covered in normal use. Building elements, building insulation, or debris have restricted access to the heated parts of the controller.
Wiring Information
The wiring diagram illustrates the connections for the DALI ECO BT RTC control unit:
- Mains Connection: Terminals for L, N, and PE (Protective Earth) for the 220-240V AC power supply.
- DALI Interface: DA- and DA+ terminals for connecting to DALI devices.
- Push Button Interface: Terminals PB1 and PB2 for connecting external push buttons.
- Resistor Installation: A 820 Ω / 5% / 1/4W resistor is shown to be installed in series with the DA+ line, within the luminaire.
- System Connections: The diagram shows connections to a DALI ECG, an OSRAM DALI Sensor, and an OSRAM DALI Push button coupler.
- Wire Preparation: Recommended wire preparation and minimum spacing of >1 cm between wires are indicated.
Conformity Declaration
OSRAM GmbH declares that the radio equipment type DALI ECO BT RTC control complies with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at: www.osram.com/lms-ce.
Frequency Range: 2402 - 2480 MHz
Max. HF Output (EIRP): 4dBm
Manufacturer Information
OSRAM GmbH
Berliner Allee 65
86153 Augsburg
Germany
Website: www.osram.com
Inventronics
Inventronics
