Buy musical instruments online from the market leader – United States
User Manual for STAIRVILLE models including: 276238 DJ Lase 40-G MK-III Showlaser, 276238, DJ Lase 40-G MK-III Showlaser, MK-III Showlaser, Showlaser
Stairville DJ Lase 40-G MK-III DMX IR – Thomann UK
Stairville DJ Lase 40-G MK-III DMX IR – Thomann Nederland
File Info : application/pdf, 52 Pages, 605.88KB
DocumentDocumentUser Manual DJ Lase 40-G MK-III Showlaser Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 Internet: www.thomann.de 20.10.2023, ID: 276238 (V6) Table of contents Table of contents 1 General information................................................................................................................................. 5 1.1 Symbols and signal words............................................................................................................... 5 2 Safety instructions..................................................................................................................................... 8 3 Features....................................................................................................................................................... 15 4 Installation.................................................................................................................................................. 16 5 Starting up.................................................................................................................................................. 22 6 Connections and controls................................................................................................................... 24 7 Operation.................................................................................................................................................... 31 7.1 Starting and stopping the device............................................................................................... 31 7.2 Main menu.......................................................................................................................................... 33 7.3 Menu overview................................................................................................................................. 36 7.4 Functions in `DMX' mode.............................................................................................................. 36 7.5 Pattern list........................................................................................................................................... 39 8 Technical specifications....................................................................................................................... 41 9 Plug and connection assignments.................................................................................................. 44 10 Troubleshooting...................................................................................................................................... 45 11 Cleaning....................................................................................................................................................... 47 12 Protecting the environment.............................................................................................................. 48 3 DJ Lase 40-G MK-III Showlaser 4 DJ Lase 40-G MK-III Showlaser General information 1 General information This document contains important instructions for the safe operation of the product. Read and follow the safety instructions and all other instructions. Keep the document for future refer- ence. Make sure that it is available to all those using the product. If you sell the product to another user, be sure that they also receive this document. Our products and documentation are subject to a process of continuous development. They are therefore subject to change. Please refer to the latest version of the documentation, which is ready for download under www.thomann.de. 1.1 Symbols and signal words In this section you will find an overview of the meaning of symbols and signal words that are used in this document. 5 DJ Lase 40-G MK-III Showlaser General information Signal word DANGER! WARNING! NOTICE! Warning signs Meaning This combination of symbol and signal word indicates an immediate dangerous situation that will result in death or serious injury if it is not avoided. This combination of symbol and signal word indicates a pos- sible dangerous situation that can result in death or serious injury if it is not avoided. This combination of symbol and signal word indicates a pos- sible dangerous situation that can result in material and environmental damage if it is not avoided. Type of danger Warning high-voltage. Warning laser radiation. Warning dangerous optical radiation. 6 DJ Lase 40-G MK-III Showlaser Warning signs General information Type of danger Warning suspended load. Warning danger zone. 7 DJ Lase 40-G MK-III Showlaser Safety instructions 2 Safety instructions Intended use This unit is used to project laser light effects; it is intended for show applications only. Use the device only as described in this user manual. Any other use or use under other operating con- ditions is considered to be improper and may result in personal injury or property damage. No liability will be assumed for damages resulting from improper use. This device may be used only by persons with sufficient physical, sensorial, and intellectual abilities and having corresponding knowledge and experience. Other persons may use this device only if they are supervised or instructed by a person who is responsible for their safety. Extend the operating life of the device by regular breaks and by avoiding frequent switching on and off. The device is not suitable for continuous operation. Safety DANGER! Risk of injury and choking hazard for children! Children can suffocate on packaging material and small parts. Children can injure themselves when handling the device. Never allow children to play with the packaging material and the device. Always store packaging material out of the reach of babies and small children. Always dispose of packaging material properly when it is not in use. Never allow children to use the device without supervi- sion. Keep small parts away from children and make sure that the device does not shed any small parts (such knobs) that children could play with. 8 DJ Lase 40-G MK-III Showlaser Safety instructions DANGER! Danger to life due to electric current! Within the device there are areas where high voltages may be present. Never remove any covers. There are no user-serviceable parts inside. Do not use the device when covers, safety equipment or optical components are missing or damaged. DANGER! Danger to life due to electric current! A short circuit could lead to a fire hazard and risk of death. Always use proper ready-made insulated triple-core mains cable with a safety plug. Do not modify the mains cable or the plug. In case of isolation damage, disconnect immediately the power supply and arrange repair. If in doubt, seek advice from a qualified electrician. WARNING! Risk of injury from laser! This device contains a class 3B laser, classified according to EN 60825-1:2014+A11:2021. The laser may only be installed and operated by a laser protection representative who is familiar with the legal regulations at the operating location. Familiarise yourself with the regulations applicable in the country of operation. The accessible laser radiation is in a wavelength range of between 302.5 nm and 1 m, the output is between 5 mW and 500 mW. Looking into the laser beam or its reflections can cause injuries to the eyes and result in irreversible damage, especially if the beam cross-section is bundled by optical collecting instru- ments. Skin contact can result in burns. Highly flammable and explosive materials within the range of the laser radiation can ignite. When work is performed on the laser system while it is functional, unintentional contact with the laser beam is possible. As the oper- ator, observe the applicable legal duties regarding safe operation before putting the device into service. Install the laser system in such a way that persons are not at risk while it is in operation. The laser may only be installed and operated by a laser protection representative who is familiar with the legal regulations at the operating location. Only operate the laser system in separate super- vised areas. If necessary, use technical protection measures to reduce the range of the laser or reduce the beam intensity. Do not look into the laser beam or its reflections. Do not use optical collecting instruments (such as magnifying glasses or lenses) to look into the laser beam, and ensure that laser beams are not directed to areas where optical collecting instruments are used. Do not expose any limbs to the laser beam. Keep the range of the laser beams and areas that can be reached by reflected laser beams free from flammable and explosive materials. Always wear laser safety glasses in line with DIN EN 207 when working on the functional laser system. Have all work and repairs on class 3B lasers performed by trained experts. Never open a class 3B laser and do not make any technical changes. 9 DJ Lase 40-G MK-III Showlaser Safety instructions WARNING! Risk of injury due to stray laser radiation! Additional components inadequately secured to the device as well as reflective objects and surfaces at the operating location can cause stray laser radiation, which can cause injuries. Make sure that additional components are always secured adequately. Make sure there are no reflective objects or surfaces in the range of the laser beams. WARNING! Risk of eye damage caused by high light intensity! The device generates highly intense light radiation. Looking directly into the light source can damage the eyes. Never look directly into the light source. WARNING! Risk of epileptic fit due to flashing lights! The device emits flashing lights (strobe effects). Flashing lights can trigger epileptic fits in specific people. If you are at risk of epi- lepsy, avoid spending longer periods of time subjected to flashing lights and looking into strobing light. NOTICE! Risk of fire due to covered vents and neighbouring heat sources! If the vents of the device are covered or the device is operated in the immediate vicinity of other heat sources, the device can over- heat and burst into flames. Never cover the device or the vents. Do not install the device in the immediate vicinity of other heat sources. Never operate the device in the immediate vicinity of naked flames. 10 DJ Lase 40-G MK-III Showlaser Safety instructions NOTICE! Damage to the device if operated in unsuitable ambient conditions! The device can be damaged if it is operated in unsuitable ambient conditions. Only operate the device indoors within the ambient conditions specified in the "Technical specifications" chapter of this user manual. Avoid operating it in environments with direct sun- light, heavy dirt and strong vibrations. Avoid operating it in environments with strong temperature fluctuations. If temperature fluc- tuations cannot be avoided (for example after transport in low outside temperatures), do not switch on the device immediately. Never subject the device to liquids or moisture. Never move the device to another location while it is in operation. In environments with increased dirt levels (for example due to dust, smoke, nicotine or mist): Have the device cleaned by qualified specialists at reg- ular intervals to prevent damage due to overheating and other malfunctions. NOTICE! Damage to the device due to high voltages! The device can be damaged if it is operated with the incorrect voltage or if high voltage peaks occur. In the worst case, excess vol- tages can also cause a risk of injury and fires. Make sure that the voltage specification on the device matches the local power grid before plugging in the device. Only operate the device from professionally installed mains sockets that are protected by a residual current circuit breaker (FI). As a precaution, disconnect the device from the power grid when storms are approaching or it the device will not be used for a longer period. NOTICE! Risk of fire due to installation of a wrong fuse! Using fuses of a different type than compatible with the device may cause a fire and seriously damage the device. Only use fuses of the same type. Observe the labelling on the device casing and the information in the "Technical data" chapter. NOTICE! Risk of fire due to incorrect polarity! Incorrectly inserted batteries may cause fires and destroy the device and the batteries. Observe the markings on the batteries and on the device. Ensure that proper polarity is observed when inserting batteries. DJ Lase 40-G MK-III Showlaser 11 Safety instructions NOTICE! Possible damage due to leaking batteries! Batteries can leak and cause permanent damage to the device. Take the batteries out of the device if it is not going to be used for an extended period of time. NOTICE! Possible staining due to plasticiser in rubber feet! The plasticiser contained in the rubber feet of this product may react with the coating of the floor and cause permanent dark stains after some time. If necessary, use a suitable mat or felt slide to prevent direct contact between the device's rubber feet and the floor. 12 DJ Lase 40-G MK-III Showlaser Duties of the operator Safety instructions As the operator of the laser system, you must comply with legal occupational safety obliga- tions as per the OStrV (in Germany). The following applies in particular: n Before putting into service, draw up an assessment of the risk posed by the direct and indi- rect effects of laser beams in line with the regulations applicable at the operating location. n Report the operation of the laser system to the responsible authorities and professional associations in line with the legislation. If the laser system is to be operated outdoors, where it could pose a risk to public traffic spaces, involve the traffic authorities responsible at the operating location (for example air traffic control) in your planning. n Make sure that a registered laser safety representative is appointed in writing before the device is put into service, and that this person ensures the safe operation of the laser system, in particular if persons unable to assess the dangers of a class 3B laser can enter the area of the laser beams. n Take adequate measures to prevent the risk of fire and explosion. n Apply appropriate technical safety measures (e.g. shielding, protective walls, barriers) on the basis of the exposure limits determined in the risk assessment. n Restrict the range of the laser beams to a limited area in order to reduce the risk to persons as much as possible. n Apply safety measures (e.g. extraction) if the effects of laser radiation can generate harmful concentrations of hazardous substances (e.g. gases, mists, aerosols). n Mark the danger zone in the immediate vicinity of the laser with appropriate signage if the event requires persons to have direct access to the laser system (e.g. stage, studio). n Use technical and organisational safety measures to restrict access to the running laser system for unauthorised persons. n Indicate the use of the laser by means of audible or visible warning signals (e.g. warning light) in the danger zone. DJ Lase 40-G MK-III Showlaser 13 Safety instructions n Use an additional safety switch (emergency stop switch) installed in an easily accessible central monitoring location (e.g. control room) that switches off the laser immediately and safely in the event of danger. n Always remove the key from the key switch when not using the laser, in order to prevent unintentional laser radiation and unauthorised use. n Instruct staff on the basis of the risk assessment and familiarise them with the necessary safety measures. n Provide staff with the required personal protective equipment (PPE). 14 DJ Lase 40-G MK-III Showlaser 3 Features Features The showlaser is specially suited for discos, clubs, bars, small stages, etc. It allows smooth inte- gration into light shows, but can also be operated as stand-alone device. Special features of the device: n Control via DMX (8 channels), buttons and display on the device and supplied IR remote control (item no. 277447) n Built-in automatic show programmes n Sound control n Master / slave mode n 32 different patterns n Laser diode: green (40 mW) DJ Lase 40-G MK-III Showlaser 15 Installation 4 Installation Unpack and check carefully there is no transportation damage before using the unit. Keep the equipment packaging. To fully protect the product against vibration, dust and moisture during transportation or storage use the original packaging or your own packaging material suitable for transport or storage, respectively. You can install the device standing or hanging. When in use, the device must be mounted at a solid surface or clamped to an approved truss. Work from a stable platform whenever you install or move the device or when you perform any kind of maintenance. Block access under the work area. WARNING! Risk of injury due to missing or incorrectly dimensioned laser safety glasses! When work is performed on the laser system while it is functional, unintentional contact with the laser beam is possible. There is a risk of injury to the eyes and the risk of irreversible damage. Always wear correctly dimensioned laser safety glasses in line with DIN EN 207 when working on the functional laser system. 16 DJ Lase 40-G MK-III Showlaser Installation WARNING! Risk of injury due to improper installation! If the laser is set up incorrectly and the installation point is too low or too close to persons, there is an increased risk of injury due to the high intensity of the laser beam. The laser may only be installed by a laser protection representative who is familiar with the legal regulations at the operating location. In order to comply with the maximum legal exposure limits, determine the actual radiation intensities at the operating location as well as the distances for laser attachment, and install the laser in line with the ambient conditions. Make sure the laser is firmly attached, and prevent the laser beam from leaving the planned laser beam area (e.g. through screens, housings or software-specific direction restrictions). Shield laser beams from each other if multiple lasers are operated simultaneously. Install the laser in such a way that the laser beam does not enter any traffic zones. DJ Lase 40-G MK-III Showlaser 17 Installation 18 DJ Lase 40-G MK-III Showlaser WARNING! Risk of injury due to stray laser radiation! Additional components inadequately secured to the device as well as reflective objects and surfaces at the operating location can cause stray laser radiation, which can cause injuries. Make sure that additional components are always secured adequately. Make sure there are no reflective objects or surfaces in the range of the laser beams. WARNING! Risk of injury in case of operation without a safety switch! There is a risk of injury if the laser is operated without a safety switch. Connect an approved external safety switch (not included in the scope of delivery) to the designated connection socket on the device. It must be possible to switch off the laser safely in the event of danger by pressing the safety switch. Installation WARNING! Risk of injury due to inadequate warning signals! Persons unable to assess the dangers of a class 3B laser are at increased risk of injury and irreversible damage if such persons are not informed of the use of the laser. Indicate the use of the laser by means of audible or visible warning signals (e.g. warning light) in the danger zone. WARNING! Risk of injury from falling devices that were inadequately secured! If devices are not properly secured during assembly, they can cause severe injury and considerable damage by falling. When installing and operating, make sure to follow the standards and regulations that apply in your country. Always secure the device with a secondary safety attachment, such as a safety cable or a safety chain. DJ Lase 40-G MK-III Showlaser 19 Installation NOTICE! Risk of overheating and fire due to inadequate distance and bad ventilation! If the distance between the light source and the illuminated surface is too short or the device is badly ventilated, the device can overheat and cause fires. Make sure that illuminated surfaces are more than 2 m away. Do not operate the device in ambient temperatures above 40 °C. Always ensure sufficient ventilation at the operating location. Safety switch (emergency stop) Connect the external safety switch (not supplied) to the provided connection socket on the device. If you press the external switch, the laser beam will be switched off immediately. Observe the safety instructions of the switch manufacturer and the regulations for the intended use. 20 DJ Lase 40-G MK-III Showlaser Installation Inserting the battery into the remote control Push the lock of the battery holder towards the centre of the housing and pull out the battery holder like a drawer. Insert the batteries. The battery is correct if the positive pole points to the housing base of the remote control. Slide the battery holder back into the remote until it clicks into place. When shipping, the battery is already installed in the remote and protected against discharge by a transparent plastic film. Remove the plastic film before initial use. NOTICE! Risk of fire due to incorrect polarity! Incorrectly inserted batteries may cause fires and destroy the device and the bat- teries. Observe the markings on the batteries and on the device. Ensure that proper polarity is observed when inserting batteries. NOTICE! Possible damage due to leaking batteries! Batteries can leak and cause permanent damage to the device. Take the batteries out of the device if it is not going to be used for an extended period of time. DJ Lase 40-G MK-III Showlaser 21 Starting up 5 Starting up Create all connections while the device is off. Use the shortest possible high-quality cables for all connections. Take care when running the cables to prevent tripping hazards. NOTICE! Data transfer errors due to improper wiring! If the DMX connections are wired incorrectly, this can cause errors during the data transfer. Do not connect the DMX input and output to audio devices, e.g. mixers or ampli- fiers. Use special DMX cables for the wiring instead of normal microphone cables. 22 DJ Lase 40-G MK-III Showlaser Connections in DMX mode Starting up Connect the DMX input of the device to the DMX output of a DMX controller or another DMX device. Connect the output of the first DMX device to the input of the second one, and so on to form a daisy chain. Always ensure that the output of the last DMX device in the daisy chain is terminated with a resistor (110 , ¼ W). Connections in master/slave mode When you configure a group of devices in master/slave mode, the first unit will control the other units for an automatic, sound-activated, synchronized show. This function is ideal when you want to start a show immediately. Connect the DMX output of the master device to the DMX input of the first slave device. Then connect the DMX output of the first slave device to the DMX input of the second slave device and so on. DJ Lase 40-G MK-III Showlaser 23 Connections and controls 6 Connections and controls Front DJ Lase 40-G MKIII ö #% $ 24 DJ Lase 40-G MK-III Showlaser Connections and controls 1 Laser aperture 2 [POWER] | Shows that the device is turned on. 3 [MUSIC] | Shows that a sound or music signal is being detected. Indicates that a sound signal is received. Lights up briefly on incoming infrared signals from the remote. 4 [IR] | Receiver for the infrared signal of the remote control DJ Lase 40-G MK-III Showlaser 25 Connections and controls Back ' ( ) & ,1 [[[ *+ -. /0 26 DJ Lase 40-G MK-III Showlaser Connections and controls 5 IEC chassis plug for the mains cable with fuse holder 6 [OUTPUT] | DMX output 7 [INPUT] | DMX input 8 Safety cable eyelet 9 [LOCK] | Safety key switch. Turns the laser output on or off. 10 [REMOTE] | Connection for an external safety switch (e.g. an emergency-stop button) 11 Display 12 [FUNC] | Opens the main menu. 13 [UP] | Increases the displayed value by one. 14 [DOWN] | Decreases the displayed value by one. 15 [ENTER] | Selects an option of the respective operating mode. 16 [MIC] | Microphone for the "sound" mode DJ Lase 40-G MK-III Showlaser 27 Connections and controls infrared remote control (item no. 277447) # ö % ' * Since the universal remote control can be used for several device types, some buttons may not be assigned and therefore have no function. & $ AUTO MUSIC ON/OFF % ) ABC 123 ( 456 789 0 -/-- Laser Remote + , 28 DJ Lase 40-G MK-III Showlaser Connections and controls 1 [AUTO] | Starts an automatic show in random order. 2 [MUSIC] | Starts a sound-controlled automatic show in random order. 3 [ON/OFF] | When the device is in the "auto show" mode or is performing a self test, press the button for several sec- onds to enter the "remote control" mode. When the device is already in the `Remote control' mode, this button switches the laser on or off. 4 Changes the colours used for representing the patterns. For item no. 276235, item no. 276238 and item no. 272917: no function 5 Stops or restarts a running show. 6 [A] | Switches to the previous pattern. For item no. 255628: Switches the flash effect for the red laser on or off. 7 [B] | Changes the sensitivity and thus the response of the microphone. First, press [MUSIC], then press [B] followed by a key from [0] to [9] on the numeric keypad.. For item no. 255628: Switches the flash effect for the green laser on or off. 8 [C] | Switches to the next pattern. For item no. 255628: no function 9 Numeric keypad for direct input of values (microphone sensitivity or pattern number). To enter two-digit numbers, press [-/--] before the first digit and before the second digit.. For item no. 255628: Numeric keypad for direct input of values (flash frequency, motor speed, speed of the double burst grating effect). DJ Lase 40-G MK-III Showlaser 29 Connections and controls 10 Toggles between the current and the previously displayed pattern. For item no. 255628: Controls the motor speed of the laser optics in conjunction with the numeric keypad. 11 [-/--] | Shift button for entering two-digit numbers. For item no. 255628: Controls the double burst grating effect in conjunction with the numeric keypad. 30 DJ Lase 40-G MK-III Showlaser Operation 7 Operation 7.1 Starting and stopping the device WARNING! Risk of injury due to improper operation! There is a risk of injury if the device is not operated properly. Only operate the laser after approval has been granted, and under the supervi- sion of a laser protection representative. DJ Lase 40-G MK-III Showlaser 31 Operation Starting Stopping Perform the following steps to start up the device: 1. Verify that all required laser safety precautions have been taken. Make sure that there is no one in the reach of the laser beam. 2. Connect the [REMOTE] connection (10) to an external safety switch (e.g. emergency stop switch) or another equivalent system with a protection function. 3. Insert the safety key into the lock (9). 4. If you have not already done so, connect the device to the mains (5). 5. After a few seconds, the fan and the motors start to work. The display shows the current operation mode. The device is now operational. 6. Turn the safety key (9) to the "ON" position to turn the laser beam on. Perform the following steps to stop the device: 1. Turn the safety key (9) to the "OFF" position to turn the laser beam off and remove the key. Keep the safety key in a secure place. 2. Disconnect the device from the mains (5). 32 DJ Lase 40-G MK-III Showlaser Operation 7.2 Main menu Press [FUNC] to activate the main menu and select an operating mode. When the display flashes, use the [UP] and [DOWN] buttons to change the displayed value. When the display shows the desired value, press [ENTER]. To return to the main menu without any changes, press [FUNC] or wait a minute. All previous settings are retained even when you disconnect the device from the power grid. Operating mode `Auto-Show' Au t Press [FUNC] repeatedly until the display shows A u t . The device operates in stand-alone mode and displays a pre-programmed show that can optionally be controlled by the built-in microphone. Use the [UP] and [DOWN] buttons to choose between the pre-programmed show types listed in the table below. Press [ENTER] to store the value and to start the operation in "Auto-Show" mode. Display Au t Sou Show Automatic show in random order Sound controlled automatic show in random order DJ Lase 40-G MK-III Showlaser 33 Operation Response 5 6 "DMX" operating mode 001 "Master/slave" mode SLA Press [FUNC] repeatedly until the display shows 5 6 and starts flashing. In this menu you can adjust the sensitivity and thus the response characteristic of the microphone. Use the [UP] and [DOWN] buttons to select the settings "S 0" (sensitivity = 0, "sound" mode off) or "S 1" (low sen- sitivity) to "S 9" (high sensitivity). Press [ENTER] to save the setting. Press [FUNC] repeatedly until the display shows 0 0 1 . Now you can set the number of the first DMX channel to be used by the device (DMX address). Use the [UP] and [DOWN] buttons to select a value between 1 and 505. Press [ENTER] to save the value and to start operation in "DMX" mode. Make sure that this number matches the configuration of your DMX controller. Press [FUNC] repeatedly until the display shows S L A . In this mode, the device exactly follows the operation of the master that it is connected to. Press [ENTER] to confirm and to start opera- tion in "Master / Slave" mode. 34 DJ Lase 40-G MK-III Showlaser Remote control mode rEN Self test t St Operation Press [FUNC] repeatedly until the display shows r E N . Press [ENTER] to confirm and to start operation in 'Remote control' mode. This mode allows you to operate the device conveniently with the infrared remote control. Make sure that the infrared receiver on the front panel of the device is not obstructed. Press [FUNC] repeatedly until the display shows t S t . Press [ENTER] to start a self test. Press [FUNC] again and select another menu item to stop the self test. DJ Lase 40-G MK-III Showlaser 35 Operation 7.3 Menu overview Aut S 6 001 SLA rEN tSt Sou S 0 001 S 9 505 7.4 Functions in `DMX' mode Channe Value l 1 Operating mode selection 0...63 64...127 128...191 36 DJ Lase 40-G MK-III Showlaser Function Laser off Automatic show in random order Sound controlled automatic show in random order Channe Value l 192...255 2 0...255 3 Zoom 0...127 128...169 170...209 210...255 4 Y axis rotation (rolling) 0...127 128...191 192...255 5 X axis rotation (rolling) 0...127 128...191 192...255 Operation Function DMX mode: This setting enables the function of the other DMX channels Pattern selection ( Ä Chapter 7.5 `Pattern list' on page 39) Fixed zoom (100%...5%) Zooming in effect, speed increasing from slow to fast Zooming out effect, speed increasing from slow to fast Zooming in effect, speed increasing from slow to fast Fixed position of Y-axis (0...359°) Clockwise rotating effect, speed increasing from slow to fast Anti-clockwise rotating effect, speed increasing from slow to fast Fixed position of X-axis (0...359°) Clockwise rotating effect, speed increasing from slow to fast Anti-clockwise rotating effect, speed increasing from slow to fast DJ Lase 40-G MK-III Showlaser 37 Operation Channe Value l 6 Z axis rotation (rolling) 0...127 128...191 192...255 7 X-axis mouving 0...127 128...191 192...255 8 Y-axis moving 0...127 128...191 192...255 Function Fixed position of Z-axis (0...359°) Anti-clockwise rotating effect, speed increasing from slow to fast Clockwise rotating effect, speed increasing from slow to fast Fixed positions on X-axis Clockwise moving effect, speed increasing from slow to fast Anti-clockwise moving effect, speed increasing from slow to fast Fixed positions on Y-axis Clockwise moving effect, speed increasing from slow to fast Anti-clockwise moving effect, speed increasing from slow to fast 38 DJ Lase 40-G MK-III Showlaser 7.5 Pattern list 0 0...7 4 32...39 8 64...71 12 96...103 1 8...15 5 40...47 9 72...79 13 104...111 2 16...23 6 48...55 10 80...87 14 112...119 3 24...31 7 56...63 11 88...95 15 120...127 Operation DJ Lase 40-G MK-III Showlaser 39 Operation 16 128...135 20 160...167 24 192...199 28 224...231 17 136...143 21 168...175 25 200...207 29 232...239 18 144...151 22 176...183 26 208...215 30 240...247 19 152...159 23 184...191 27 216...223 31 248...255 40 DJ Lase 40-G MK-III Showlaser Technical specifications 8 Technical specifications Laser medium Laser power Laser class Beam diameter at aperture Pulse data Divergence (each beam) Divergence (total light) Number of DMX channels Input connections Output connections Control Power consumption Supply voltage Green: 532 nm (typical), ND: YVO4 DPSS Green: 40 mW 3B < 5 mm All pulses < 4 Hz (> 0.25 s) < 2 mrad < 90° 8 Power supply IEC chassis plug C14 DMX control XLR chassis plug, 3-pin DMX control XLR chassis socket, 3-pin DMX Infrared remote control 12 W 100 - 240 V 50/60 Hz DJ Lase 40-G MK-III Showlaser 41 Technical specifications Fuse Battery remote control International Protection Rating Mounting options Dimensions (W × H × D) Weight Ambient conditions 5 mm × 20 mm, 1.0 A, 250 V, slow blow Lithium-ion button cell CR2025, 3 V IP20 Hanging, standing 155 mm × 85 mm × 145 mm 1.26 kg Temperature range 0 °C...40 °C Relative humidity 20%...80% (non-condensing) 42 DJ Lase 40-G MK-III Showlaser Further information Colour spectrum Animation laser Grating laser ILDA DMX Power rating Analogue modulation green Yes No No Yes Up to 100 No Technical specifications DJ Lase 40-G MK-III Showlaser 43 Plug and connection assignments 9 Plug and connection assignments Introduction This chapter will help you select the right cables and plugs to connect your valuable equip- ment so that a perfect light experience is guaranteed. Please take our tips, because especially in `Sound & Light' caution is indicated: Even if a plug fits into a socket, the result of an incorrect connection may be a destroyed DMX controller, a short circuit or `just' a not working light show! DMX connections The unit offers a 3-pin XLR socket for DMX output and a 3-pin XLR plug for DMX input. Please refer to the drawing and table below for the pin assignment of a suitable XLR plug. Pin Configuration 1 Ground, shielding 2 Signal inverted (DMX, `cold signal') 3 Signal (DMX+, `hot signal') 44 DJ Lase 40-G MK-III Showlaser Troubleshooting 10 Troubleshooting WARNING! Risk of injury due to improper troubleshooting! There is a risk of injury if troubleshooting is not performed properly. Have all work and repairs on class 3B lasers performed by trained experts. In the following we list a few common problems that may occur during operation. We give you some suggestions for easy troubleshooting: DJ Lase 40-G MK-III Showlaser 45 Troubleshooting Symptom Remedy The device is not working, no light, the fan is not 1. Check the power supply and the main fuse. running 2. Check the safety key switch. 3. Check the external safety switch (e.g. emergency stop button) No response to the DMX controller 1. If the display shows a flashing number, for example "001", no DMX signal is being received. Check the DMX connectors and cables for proper connection. 2. If the display does not flash and there is no response, check the address set- tings and DMX polarity. 3. Try using another DMX controller. 4. Check whether the DMX cables run near or parallel to high-voltage cables that may cause damage or interference to a DMX interface circuit. No response to the remote control 1. Check whether the device is in "remote control" mode. The display has to show r E N . 2. Try using the remote control at a different angle to the IR sensor on the front panel of the device. When the unit receives a signal from the remote control the LED `MUSIC' lights up briefly. 3. Check the remote control battery. 46 DJ Lase 40-G MK-III Showlaser If the procedures recommended above do not succeed, please contact our Service Center. You can find the contact information at www.thomann.de. 11 Cleaning Optical lenses Fan grids Cleaning WARNING! Risk of injury due to improper cleaning! There is a risk of injury if cleaning is not performed properly. To avoid unintentional laser radiation, always remove the key from the key switch before you start cleaning the device. Clean the optical lenses, that are accessible from the outside, regularly in order to optimize the light output. The frequency of cleaning depends on the operating environment: wet, smoky or particularly dirty surroundings can cause more accumulation of dirt on the optics of the device. n Clean with a soft cloth using our lamp and lens cleaner (item no. 280122). n Always dry the parts carefully. The fan grids of the device must be cleaned of any contamination, such as dust, etc. on a reg- ular basis. Before cleaning, switch off the device and disconnect mains-operated devices from the mains. Only use pH-neutral, solvent-free and non-abrasive cleaning agents. Clean the unit with a slightly damp lint-free cloth. DJ Lase 40-G MK-III Showlaser 47 Protecting the environment 12 Protecting the environment Disposal of the packaging mate- rial For the packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly disposed of. Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging. Disposal of batteries Batteries must not be thrown away or incinerated; they must be disposed of in accordance with local regulations for the disposal of hazardous waste. Use the existing collection points for this. Only dispose of lithium batteries when they are discharged. Remove replaceable lithium bat- teries from the device before disposal. Protect used lithium batteries against short circuits, for example by covering the poles with adhesive tape. Permanently built-in lithium batteries must be disposed of together with the device. Please inquire about an appropriate collection point. 48 DJ Lase 40-G MK-III Showlaser Protecting the environment Disposal of your old device This product is subject to the European Waste Electrical and Electronic Equipment Directive (WEEE) in its currently valid version. Do not dispose with your normal household waste. Dispose of this device through an approved waste disposal firm or through your local waste facility. When discarding the device, comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility. DJ Lase 40-G MK-III Showlaser 49 Notes 50 DJ Lase 40-G MK-III Showlaser Musikhaus Thomann · Hans-Thomann-Straße 1 · 96138 Burgebrach · Germany · www.thomann.de