Instructions for Bonding Forever models including: 8809748540081, Bonding Forever, HANNAM HI-TECH, Bonding, Forever, Super, Strong, Double, Sided, Tape, Foam, Tape, Double, Sided, Adhesive, Tape, Mounting, Tape, 0.045, 60, 1EA, B08LPD9KK4, B08LPB4X1D, B08LPD4GK1, B08LQ665VD, 8809748540081, Double Sided Mounting Tape, Sided Mounting Tape, Mounting Tape
8809748540081 Comparison Chart (PDF) Bonding Forever HANNAM HI-TECH Bonding,Forever,Super,Strong,Double,Sided,Tape,|,Foam,Tape,|,Double,Sided,Adhesive,Tape,|,Mounting,Tape,|,0.045",X,1",X,60",X,1EA,B08LPD9KK4,B08LPB4X1D,B08LPD4GK1,B08LQ665VD
COMPARISON CHART ABOUT TAPE APPLICATION DOUBLE-SIDED MOUNTING TAPE SUPER STRONG SUPER STRONG Hannam Hi-Tech - 1 / 7 - Hannam Hi-tech Co. Ltd. DOUBLE-SIDED MOUNTING TAPE SUPER STRONG 1. The surface condition determines the performance of the tape. Before the application of the tape, the surface is exposed to various contamination such as dust, moisture and oil. In order to maximize the adhesive performance of the tape, the surface condition is very important. Therefore, there is a need to keep the surface clean. Polluted substances Fingerprint, Moisture Oils, Grease nasty Oil and Grease Washing of surface Ethyl alcohol, IPA, Toluene Normal heptane (n-heptane) MEK (Methyl ethyl ketone) A cleaning agent that can be easily purchased by general consumers is ethyl alcohol. Remove surface contaminants as much as possible with a dry cloth or cloth, and wipe the surface several times with ethyl alcohol. There is no slipping on the surface, and when it dries sufficiently, you may attach a tape. Examples of changes in adhesion according to surface conditions The test the change of adhesion in the external environment (fine dust concentration 70, ultra-fine dust concentration 42). 1. Adhesive performance degradation test method After exposing the surface, attach the tape. After exposing the tape, attach it to a clean surface. When the test is carried out in , it is more effective as a test method for lowering adhesion performance. Adhesion TEST at Room temp. (23 ) 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 Immediately 99.9% 92.8% 99.5% 85.6% 98.4% 72.2% 30 min passed 60 min passed 90 min passed Indoor Outdoors 95.3% 59.2% 120 min passed The graph above shows the adhesion performance according to the degree of exposure to fine dust. SUPER STRONG Hannam Hi-Tech - 2 / 7 - Hannam Hi-tech Co. Ltd. DOUBLE-SIDED MOUNTING TAPE SUPER STRONG Indoors, 95% level after 2 hours. After cleaning the surface, it is the same as 95% level when attaching after 2 hours The level of 80% is expected when 4 hours have elapsed indoors, and even less than 50% is expected if more than a day passes. Therefore, it is judged that attaching without washing does not exhibit 50% of the adhesion performance, and it can be easily separated from the attachment site. Outdoors, after 30 minutes, 92% level. It is 59% after 2 hours outdoors, indicating that the adhesion performance is very serious if contaminants such as dust are not removed. Adhesion Adhesion at Low temp. (0 ~ 5 ) 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 Immediately 94.1% 85.5% 90.7% 76.1% 85.8% 60.1% 30 min passed 60 min passed 90 min passed Indoor Outdoors 79.3% 44.7% 120 min passed The graph above shows the adhesion performance according to the degree of exposure to fine dust. At a temperature lower than room temperature, the change in adhesive performance is more severe. Adhesive performance varies depending on the cleanliness of the surface, and temperature is also one of the factors affecting the adhesive performance. SUPER STRONG Hannam Hi-Tech - 3 / 7 - Hannam Hi-tech Co. Ltd. DOUBLE-SIDED MOUNTING TAPE SUPER STRONG 2. The conditions for good adhesion performance 1) As in section 1, clean the surface before attaching. 2) After removing the liner of the tape, attach it immediately. (minimize exposure time to airborne dust, etc.) 3) Attach it to the object first, and wait until the adhesive performance is maximized. (average 24h , min 1h) Immediately 1hour 24 ~ 48 hour After attaching, wait at least 1 hour 4) Make the surface temperature as warm as possible before attaching. (A hair dryer can be used) Surface temperature: 25~35 (77~95) or higher (Enough to feel the warmth) 5) Requires compression after attaching to the fixed surface: 1 inch by 1 inch - 5kg or more - 20 seconds or more Apply pressure immediately upon attachment. A push force applied by an adult is sufficient. 6) Attachment Precautions Check whether there is a groove in the attachment Groove depth 0.4mm or less: 1.1T or more applied TAPE Groove depth 1.0mm : 1.1T not applicable, 2.0mm or more applicable If the groove depth is more than 1.0 mm, refrain from applying Groove SUPER STRONG Hannam Hi-Tech - 4 / 7 - Hannam Hi-tech Co. Ltd. DOUBLE-SIDED MOUNTING TAPE SUPER STRONG Consider the area of the tape by referring to the allowable weight according to the material of the surface. For example, it can be seen that the allowable range of a tape of a certain size changes with weight. The weight range the tape can tolerate -1. Heavy stuff 0.5 lbs 5.0 lbs Heavy Heavy Heavier NO YES YES Increase the amount of tape to be attached to make the area larger and attach it. -1. Light stuff Light Light No problem even if you attach the tape wide. No problem even if you attach the tape small. Even if a light object is attached with a small amount of tape, attach it to the four corners so that it can be supported. Applicable Exceptions. If the load is distributed as in , there is no problem, but if the center of gravity is biased forward, it may fall even after attachment. SUPER STRONG Hannam Hi-Tech - 5 / 7 - Hannam Hi-tech Co. Ltd. DOUBLE-SIDED MOUNTING TAPE SUPER STRONG For example, if there are different shaped objects with the same weight (), the amount of tape required for attachment is the same. As shown in the figure below, A did not fall, but B and C will. A B C Tape 4ea Tape 4ea Tape 2ea (sphere shape) The load on an object is the product of the weight of the object and the length to the distance to the center of gravity of the object. wt.() Force (N) x=Nx a. Length to center of gravity : A, B, C b. Weight of objects A, B, and C : c. Tape Thickness : d. The load the tape can withstand : N e. quantity of tapes : A (4ea), B (4ea), C (2ea) A Not falling 4xxN xA B Falling 4xxN < xB C Falling 2xxN < xC Since the length of A is short, there is little change in weight. Because "B" is long, the weight the weight increases as much increases by a multiple of "B" as a multiple of "C" C is sphere shape and not easy to attach, so the load that the tape can withstand is doubled because only two are attached. Do not apply tape to circular objects as much as possible. There is a risk of damage due to falling. SUPER STRONG Hannam Hi-Tech - 6 / 7 - Hannam Hi-tech Co. Ltd. DOUBLE-SIDED MOUNTING TAPE SUPER STRONG 3. Tape Specifications for Surfaces 1) Tape Size for 1 pound Material Surface Metal ; Stainless Steel Glass Painted Panel Plastic ; ABS Wood Width 1.0 inch Length 0.7 inch 0.8 inch 1.0 inch 1.0 inch 1.2 inch Load 1 POUND For example, a 2.0 lbs frame Material check: ABS Identify the required quantity of tape : 4ea Tape size : 1in by 0.5 in ; (1 in by 0.5 in) x 4ea = 2.0 lbs After cleaning the surface, attach. It is safe to attach a little larger than the calculated standard as shown in the diagram. 2) When used to attach mixmaterials Material Surface (1) Metal Metal Metal Metal Glass Glass Glass Painted Panel Painted Panel Plastic Material Surface (2) Glass Painted Panel Plastic Wood Painted Panel Plastic Wood Plastic Wood Wood Tape standard selection criteria Glass Painted Panel Plastic Wood Painted Panel Plastic Wood Plastic, Painted Panel Wood Wood SUPER STRONG Hannam Hi-Tech - 7 / 7 -Microsoft Excel 2013 Microsoft Excel 2013