Instruction Manual for Transmitter models including: GEM600M-UL, GEMD MQI-UL, MAGLOCGEM600M-UL LBS Electro Magnetic Lock, MAGLOCGEM600M-UL, LBS Electro Magnetic Lock, Electro Magnetic Lock, Magnetic Lock
Use the Allen wrench and fixing bolts to tighten the electromagnetic lock to mounting plate. Connect the power and test the holding force. Add ...
Electromagnetic Lock Quick Installation Instructions (MAGLOCGEM600M-UL and MAGLOCGEMD*MQI-UL ) Fold the mounting template 90° Place the template to the proper position of the door and frame. Mark the hole positions of the template on the door and frame. Drill the holes according to the marks. 4 Armature Plate Please install the armature plate as illustrated here. (Dimensions of the holes are depending on the door types as illustrated below.) Hollow Metal Door Reinforced Door Solid Door Outdoor Outdoor Outdoor 36mm 12.7mm 8mm 6.8mm for M8 -1.25 thread 12.7mm 8mm Drill an 8mm hole through door, on closing side enlarge to 12.7mm by a sexnut bolt on the opening side. Recommendation: Drill a 6.8mm hole and tap on closing side aM8x12.5 thread. Drill a 8mm hole thrugh door on closing side enlarge to 12.7mm, by a sexnut bolt on the opening side. The depth is 36mm. For Micro EM-locks (300 LBS), maximum thickness of door is 1.73 in. For Mini EM-locks (600 LBS), maximum thickness of door is 1.97 in. For Midi EM-locks (800 LBS), maximum thickness of door is 1.89 in. For Maxi EM-locks (1200 LBS), maximum thickness of door is 1.81 in. Outdoor The rubber washer makes the surface of the armature plate adjustable in order to completely fit the surface of magnetic lock. Fasten the mounting plate with the mounting screws. The position of the mounting plate should be adjustable. Fix the mounting plate on the door with mounting screws Use the Allen wrench and fixing bolts to tighten the electromagnetic lock to mounting plate. Connect the power and test the holding force. Add washers if there is gap between the maglock and the armature plate and then tap the screw holes. 1.Pass the power cable through the mounting plate and the hole of the maglock. 2.Place the mounting plate above the maglock. Leave a length of 1 cm from either end of the maglock. 3.Slide the mounting plate into the maglocks. Fit the maglock from the bottom to the mounting plate. 4.Use the Allen wrench and fixing screws to tighten the mounting plate and maglock. Copyright © Gianni Industries, Inc. All rights reserved. P-MU-NH-N Published on: 2017.02.15 LZ bracket for Inswing doors Use the fixing bolt to tighten the Assemble the Z bracket, and make electromagnetic lock on L bracket. sure that the position of the Z bracket is adjustable. Outdoor Outdoor Fasten the armature plate to the Z bracket (Must add rubber washer) After the maglock attracts the armature plate, adjust the Z bracket to fit the door. Fasten the Z bracket to the door. EM-NH350M and EM-NH2350M include a bond sensor and LED indicator. Door Status Sensor (dry contact output) indicates the door is in an open or closed status. Reed switch rated 0.2A/12VDC LED indicator GREEN: Unlocked RED: Locked No LED: No power Timer Adjustment Ensures the automatic lock mode after the door is closed properly and it can be adjusted from 1 to 80 seconds. (Timer Adjustment) Bond sensor output (Optional) Indicates the locked and unlocked status N.C. contact output: open status N.O. contact output: locked status Buzzer Alarm Door Held OpenAlarm is an auditory feedback for users. Alarm sounds when the door is not closed for over a specified time limit. VR timer (Timer Adjustment) is adjustable from 1 to 20 seconds. No power Make sure the wires are connected properly Check that the power supply is connected and works properly Make sure the lock switch is wired correctly Poor contact armature plate between electromagnet and Make sure if the armature plate is deformed Make sure if the rubber washer was used between the bracket and armature plate Make sure the contact surfaces of the electromagnet and armature plate are clean and free from dust and foreign material Low voltage or incorrect voltage setting Check the electromagnet lock is set for the correct voltage. Check the voltage at the electromagnetic locks input. if low, determine if the correct wire gauge is being used to prevent excessive voltage drop. A secondary diode was installed across the Remove any diode installed across the magnet for "spike" electromagnetic lock suppression. (The magnet is fitted with a metal oxide varistor to prevent back EMF) Misalignment between the armature plate and Make sure the armature plate and electromagnetic lock are aligned correctly electromagnetic lockAcrobat Distiller 11.0 (Windows)