Instruction Manual for Two HP models including: 2hp Swarm Hyper Oscillator, 2hp Swarm, Hyper Oscillator, Oscillator
2HP | Analogue Haven
2hp Swarm Hyper-Saw/Pulse Oscillator Module (silver) at Juno Records.
2hp Swarm Hyper-Saw/Pulse Oscillator Module (black) at Juno Records.
File Info : application/pdf, 3 Pages, 1.61MB
DocumentDocument2hp Swarm Hyper Oscillator Voices CV Input Range: -5V to +5V Swarm Tech Specs Width: 2HP Depth: 45mm Power Consumption: +12V=85mA, -12V=7mA, +5V=0mA Voices Controls the number of active oscillators. Only 1 oscillator is active when the knob is fully counter clockwise. 20 oscillators are active when the knob is at the center position. From there, the number of active oscillators increments to dozens of oscillators (max of 88 for Saw, 55 for Pulse) when the knob is fully clockwise. Freq 1V/Oct Input Range: -5V to +5V Freq Controls the macro pitch of all active voices. Tracks 1v/oct. Audio Output Range: 10Vpp VOICES DETUNE FREQ OUT 2hp Watch The Demo Detune CV Input Range: -5V to +5V Detune Controls the amount detune applied to each oscillator. The first half of the knob provides tasteful detune, while the second half provides chaotic detune. No detune is applied when the knob is fully counter clockwise. Wave Toggle Toggles between sawtooth (left) and pulse (right) waveforms. Discover more at https://www.twohp.com/modules/swarm Module Installation · To install your 2hp module, locate a space with the appropriate HP in your rack for installation. · Next, connect the module's power cable to your power supply. The cables on this end are keyed, though you should make sure to align the red stripes on both connectors to ensure safe and proper connection. Our illustration uses a flying bus cable, though the same action applies for busboards/alternate power solutions. See the figure below for reference: · Next, make sure your module's power cable is properly connected to your module. For 2hp modules, confirm that your cable's red stripe aligns with the white marker line on the module's PCB, just above the power header. You may notice that even though there is only 1 row of 5 pins on your 2hp module, but 2 rows on the power cable. You can use either row of 5 pin connectors on the cable with your module, so long as the red stripe is properly aligned. See figure below for reference: · Finally, mount your module to the rails using 2.5mm mounting screws and the included sliding mounting nuts. Your module is now ready to be powered on and patched! Module Pairings Swarm is a versatile sound source on its own, but here are a few considerations from our line up that we think work great with Swarm! Lo-Fi EG Lo-Fi EG Lo-Fi makes a perfect pairing IN with Swarm! Though its envelope is sim- pler than what's offered on our TRIG ADSR module, EG's curve and Crunch up your swarming saws amplitude controls are perfect WOW with the digital mode on Lo-Fi, or for dialing in the shape of your ATTACK patch together a wobbly, vintage super-saw stabs. synth melody with the analog mode. HISS Combine with a VCA, and you are ready to sequence your trance or DECAY LINEAR hardcore voice! EXPO POP A OUT 2hp AMP OUT 2hp MMF VCA MMF VCA Having an analog, state-variable Pair our analog dual VCA with EG INPUT IN filter in Swarm's signal patch is above and Swarm to have your helpful for adding shaping, dy- super-saw voice ready to go! CV namics, and timbral transitions to your super-oscillator. FREQ Use one VCA channel to shape your sound, while using another OUT High-pass out your trance lead, or channel to attenuate any mod- patch together a squelching bass ulation you may be using on RESO line. The pairings don't get much Swarm. IN better than this. CV LP HP OUT BP 2hp 2hp