Architect LED Desk Lamp

Thank you for purchasing this product. Please read this instruction carefully to understand its features and safety cautions.

Features

• Sensitive Touch Control & Wireless Remote Control
• 5 Lighting Modes & 7 Brightness Levels
• 4 Timer Stop Options & Memory Function
• Soft Light, No Flicker, Eye Protection [Eye-caring]
• Adjustable Silicone gooseneck & Sturdy Base
• Ultra-wide Angle Irradiation Range
• Equipped with USB Charging Port [USB]

Controls: [Touch Control], 5 Color Modes, [Dimmable], [Timer], [USB], [Remote Control], [Eye-caring], 360°

Parts Indicator

Diagram showing the components of the desk lamp:

• Touch Control: The control interface on the lamp base.
• Flexible Arm: The adjustable neck of the lamp.
• Head: Contains the LED light source.
• Lamp Pole: Connects the head/arm to the base.
• Base: The stable foundation of the lamp.
• Remote Control: Wireless device for operation.
• Timing Indicator: Light indicating timer status.
• USB Output: Port for charging external devices.
• Power Interface: Connection point for the power adapter.

Lamp Angles: The lamp head and arm can be adjusted to a normal use angle range, with a 180° range for the lamp holder and arm. When adjusting the lamp head angle, press the base simultaneously. (Illustrations are for reference only.)

Operating Instructions

Initial Power On: When the product is powered on, all white buttons will light up with low brightness. They will turn to high light when the lamp is turned on.

ON/OFF Switch

Single touch to turn the light on or off.

Memory Function: The lamp remembers the last used brightness and mode when powered on.

Stop Timer: Long press the switch for 2 seconds to activate a 1-hour timer. Long press again for 2 seconds to cancel. When the timer is active, the backlight will pulse every 2 seconds. When canceled, the backlight remains steady.

Brightness Adjustment

When the light is on, click the +/- buttons to adjust brightness. Brightness can be adjusted in 7 steps: 10%-25%-40%-55%-70%-85%-100%.

Mode Switch (Color Temperature)

When the light is on, click to cycle through 5 color temperature modes: 2800K, 3500K, 4200K, 5000K, 6000K.

Wireless Remote Control (Requires 3 AAA batteries)

1. Single press the top cover to turn the light on/off.
2. Rotate the top cover to steplessly adjust brightness (clockwise for brightest, counterclockwise for darkest).
3. Long press the top cover to cycle through the 5 color temperatures. Each setting stays for 1.2 seconds before moving to the next.

Timer Function (Remote Control)

1. Double-click and press the top cover to enter timing selection. The timing indicator will light up and flash. Rotate the top cover to select one of four timings: 30 minutes, 60 minutes, 90 minutes, or 120 minutes. Single press again to confirm. The timing indicator will stop flashing, and the lamp's touch switch backlight will pulse for 2 seconds.
2. After activation, the indicator bar will turn off after 10 seconds. Any slide on the remote will wake it up. The indicator bar will extinguish one by one as time decreases. When the timer ends, all indicators will turn off, and the main light will also switch off.

Cancellation Timing

When the timer is active, double-click the remote control's top cover to cancel the timer. The lamp's touch switch backlight will pulse for 2 seconds.

Remote Control Pairing and Maintenance

Remote Control Pairing: If the remote control fails, re-pair it with the desk lamp. With the lamp powered on but the light off, long press the main light on/off switch for 5 seconds. The main light will pulse, indicating pairing mode. Short press the remote control to start pairing. The main light will stop flashing upon successful pairing. Pairing mode exits after 30 seconds of inactivity.

[Low Battery Reminder]: When the remote control battery is low, the indicator light bar will flash rapidly for three seconds and enter a non-working state.

Installation Diagram

Follow these steps to assemble the desk lamp:

1. Step 1: Insert the rear end of the lamp body into the upper end of the lamp pole and fasten with screws.
2. Step 2: Align the bottom of the light pole with the two holes of the base and tighten the two screws using a wrench.
3. Step 3: Unfold the light bar. Align the four iron pieces on the back of the light bar with the card slot holes of the light head, insert them, and press the lower part of the light bar into the groove.
4. Step 4: Insert the adapter and turn on the touch switch to start working.

How to replace the battery of the remote control:

1. Hold the bottom cover of the remote control with one hand and the main body with the other. Rotate in the indicated direction. When you hear a click, the lower cover can be removed to replace the battery.
2. After placing the new battery, reinsert the lower cover, rotate it into place, and snap it shut for normal use.

Specifications

Packing List

The package includes:

• Lamp Head
• LED Lamp Bar
• Lamp Pole
• Base
• Remote Control
• Battery (Built-in AAA *3 for remote)
• Screws
• Wrench
• Adapter
• User Manual

Operation Cautions

• Do not wipe the lamp with highly volatile or corrosive liquids to avoid discoloration or damage.
• Do not place the lamp on high-temperature surfaces or use it in flammable or humid environments to prevent breakdown or short circuits.
• The external cable or cord of the lamp should not be replaced.
• The light source of this lamp is irreplaceable. The entire luminaire must be replaced when the light source expires.
• When the lamp is working, do not look directly at the light source to avoid eye damage.
• The product contains a battery. Do not dispose of it in fire to avoid explosion.

FCC Warning Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

[FCC CE RoHS]