Vortex T10M Pro+

Device Overview

The tablet features a 3.5mm audio jack, volume buttons (Volume±), a power button, a 5MP front camera, and a microphone (Mic 1).

Volume Buttons: Short press to adjust the volume or to mute incoming calls.

The rear of the tablet features an 8MP main camera with an LED flash. It also includes a Type-C USB port and slots for a SIM/T-flash card. The device is equipped with two speakers.

Power Button: Long press to turn on the device. When the device is on, a short press of the Power Button shuts down or turns on the screen.

Card Insertion

Nano-SIM Card

Insert a Nano SIM card with the chip facing down. Note the orientation of the SIM card's cut corner when inserting into the slot.

Reminder: Use only standard Nano-SIM cards. Do not use non-standard cards.

TF Card Installation

Place the TF card with the metal contacts facing down. Align the card with the cut edge and insert it directly into the device.

Reminder: Turn off the tablet before changing or replacing the TF card. TF cards are sold separately.

Important: Do not insert or remove the SIM card while the tablet is powered on.

SIM Management

To set the primary SIM for 4G network, navigate to Settings > SIM Card. To select preferred network types (4G/3G/2G), go to Settings > Network & Internet > Mobile network > Preferred network type.

Network Connection

Connecting to Wi-Fi

Navigate to Settings > Network & Internet > Wi-Fi. When Wi-Fi is enabled, a list of available connections will appear. Select a network, enter the password if required, and click Connect. For public networks, simply click Connect. A 'connected' status indicates availability.

Bluetooth Function

Go to Settings > Connected devices > Bluetooth. Enable Bluetooth by clicking the Menu Button and selecting 'Refresh'. The tablet will scan for available Bluetooth devices. Tap a device to pair and confirm with 'Pair' in the pop-up dialog. File transfer is possible after successful pairing.

Reminder: Swipe down from the status bar to access quick settings for Bluetooth and other functions.

Wi-Fi Hotspot Setting

Activate the Portable Wi-Fi Hotspot by navigating to Settings > Network & tethering > Wi-Fi hotspot. During setup, enter your desired 'Network Name' and password, then click Save.

Reminder: Ensure Data Connection is enabled before activating the hotspot. Mobile data will be shared; use with caution. Hotspot signal strength depends on device and network conditions.

Camera

Aim the camera at your subject for automatic focus, or tap the screen to select a focus point and press the 'Capture' icon to take photos. Explore other modes like video recording, beautifying, and panorama for photos and videos.

SIM Card & SD Card

The device features a single SIM card slot and an SD card slot. It does not support Dual SIM functionality.

Security Information

Third-party software installation and functionality may vary based on regional and hardware specifications. Vortex disclaims responsibility for performance issues or incompatibilities arising from third-party applications, registry edits, or OS modifications. Unauthorized OS customization may lead to device or application malfunction.

Safety Precautions:

• Avoid exposing the device or battery to extreme cold or heat, as this can cause deformation and reduce battery life and capacity.
• Use only Vortex-approved batteries and chargers. Incompatible accessories may damage the tablet. Dispose of batteries and the tablet according to local regulations.
• Do not place the device or battery near heating elements like microwaves, ovens, or radiators, as the battery could explode if overheated.
• Do not crush or puncture the battery. Protect it from external high pressure, which can cause internal shorts and overheating.

Specifications

Basic Information

Display

Cameras

Connection (I/O)

Other Features

In the Box

• 1 x Tablet
• 1 x Type-C Cable
• 1 x Power Adapter
• 1 x Quick Start Guide
• 1 x TPU Case

Safety Statement

FCC Caution

Unauthorized changes or modifications may void the user's authority to operate the equipment. This device complies with FCC Rules Part 15, subject to two conditions: (1) it must not cause harmful interference, and (2) it must accept any received interference, including that which may cause undesired operation.

Note: This equipment has been tested and complies with Class B digital device limits under FCC Rules Part 15, providing reasonable protection against harmful interference in residential installations. It generates, uses, and radiates radio frequency energy. Improper installation or use may cause radio communication interference. While interference is not guaranteed to be absent in all installations, if interference occurs with radio or television reception (detectable by powering the device on/off), users are advised to try the following:

• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and receiver.
• Connect the equipment to a different circuit than the receiver.
• Consult a dealer or qualified radio/TV technician.

ISEDC Warning

Operation within the 5150-5250 MHz frequency range is limited to indoor use. This device complies with Innovation, Science, and Economic Development Canada's licence-exempt RSS standard(s). Operation is permitted under two conditions: (1) the device must not cause interference, and (2) the device must accept any interference, including interference that may affect its operation.

Specific Absorption Rate (SAR) Information

SAR tests are performed using standard operating positions approved by the FCC/ISEDC, with the device transmitting at its highest certified power level across all tested frequency bands. While SAR is determined at the highest certified level, the actual SAR level during operation may be significantly lower. Before public release, new models must be tested and certified by the FCC/ISEDC to ensure they do not exceed established exposure limits. Tests are conducted in positions and locations mandated by the FCC/ISEDC. For body-worn operation, this model has been tested and meets FCC/ISEDC RF exposure guidelines when used with a product-designated accessory or an accessory without metal that positions the handset at least 0mm from the body. Failure to comply with these restrictions may result in violation of RF exposure guidelines.

French SAR Information: SAR tests are conducted using standard operating positions accepted by the FCC/ISEDC with the phone transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. Before a new model phone is available for sale to the public, it must be tested and certified to the FCC/ISEDC that it does not exceed the exposure limit established by the FCC/ISEDC, tests for each phone are performed in positions and locations as required by the FCC/ISEDC.

French Body-worn Operation: For body-worn operation, this phone model has been tested and complies with FCC/ISEDC RF exposure directives when used with a product-designed accessory or an accessory without metal, positioned at least 0 mm from the body. Non-compliance with these restrictions may lead to a violation of RF exposure directives.

English Body-worn Operation: This device has been tested and meets FCC/ISEDC RF exposure guidelines when used with a leather case. Users must use the provided leather case. Using other leather cases may not guarantee compliance with FCC/ISEDC RF exposure guidelines.

French Body-worn Leather Case Operation: For body-worn operation, this device has been tested and complies with FCC/ISEDC RF exposure directives when used with a leather case. Users must use this leather case. Using other leather cases may not ensure compliance with FCC/ISEDC RF exposure directives.

EU Compliance Notice:

⚠ EU Member States: BE, BG, CZ, DK, DE, EE, IE, EL, ES, FR, HR, IT, CY, LV, LT, LU, HU, MT, NL, AT, PL, PT, RO, SI, SK, FI, SE, NO, IS, LI, CH, TR.

Operation of 5150-5250 MHz is restricted to indoor use only in all EU member states.

Made in China