Parts Breakdown - Makita BJR182
This document provides a detailed parts breakdown for the Makita BJR182 reciprocating saw. The diagram on page 1 visually represents the components listed in the table below.
| Fig # | Part ID | Part Name | Quantity |
|---|---|---|---|
| 1 | 163451-9 | SHOE, JR3050T | 1 |
| 2 | 424046-6 | INSULATION COVER, BJR182Z | 1 |
| 3 | 424147-0 | PROTECTOR, JR3050T | 1 |
| 4 | 421894-4 | PROTECTOR, JR3050T | 1 |
| 5 | 257952-8 | RETAINING RING (EXT) 18, JR3060T | 1 |
| 6 | 310285-3 | DRIVING SLEEVE, JR3050T | 1 |
| 310160-3 | DRIVING SLEEVE, JR3050T | 1 | |
| 7 | 256492-3 | SHOULDER PIN 5, JR3050T | 1 |
| 8 | 233345-3 | COMPRESSION SPRING 6, JR3050T | 1 |
| 9 | 268094-3 | PIN 3, JR3050T | 1 |
| 10 | 331720-8 | GUIDE SLEEVE, JR3060T | 1 |
| 11 | 256158-5 | PIN 3, LS1016L | 1 |
| 12 | 417791-0 | DRIVING SLEEVE GUIDE, JR3050T | 1 |
| 13 | 418311-3 | SLEEVE, JR3050T | 1 |
| 14 | 345214-7 | PUSH PLATE, BJR240SH | 1 |
| 15 | 233025-1 | COMPRESSION SPRING 2, JR3050T | 1 |
| 16 | 231687-9 | TORSION SPRING 17, JR3050T | 1 |
| 17 | 213151-2 | OIL SEAL 14, 6903VD | 1 |
| 18 | 213174-0 | X RING 14, JR3030 | 1 |
| 19 | 154813-2 | GEAR HOUSING COVER CPL.,BJR181 | 1 |
| 21 | 418806-6 | CAP, JR3050T | 1 |
| 22 | 911243-8 | P.H. SCREW M5X25, GA7911 | 4 |
| 23 | 232221-8 | LEAF SPRING (A), JR3050T | 1 |
| 24 | 162236-0 | SHIFT BUTTON, JR3050T | 1 |
| 25 | 421946-1 | SEAL RING, BJR181 | 1 |
| 26 | 345480-6 | SLIDE PLATE, JR3050T | 1 |
| 27 | 214170-1 | PLANE BEARING, JR3060T | 1 |
| 28 | 341462-6 | PLATE, JR3000V | 1 |
| 29 | 911225-0 | PAN HEAD SCREW M5X16, JR3050T | 2 |
| 30 | 168405-1 | SLIDER, JR3050T | 1 |
| 31 | 154788-5 | SLIDER CPL., JR3050T | 1 |
| 32 | 214170-1 | PLANE BEARING, JR3060T | 1 |
| 33 | 341462-6 | PLATE, JR3000V | 2 |
| 34 | 911225-0 | PAN HEAD SCREW M5X16, JR3050T | 2 |
| 35 | 265148-7 | TORX S.HEAD SCREW M5X14, JR3050T | 2 |
| 36 | 344795-8 | PLATE C, JR180DWB | 1 |
| 37 | 265148-7 | TORX S.HEAD SCREW M5X14, JR3050T | 2 |
| 344795-8 | PLATE C, JR180DWB | 1 | |
| 38 | 212959-1 | NEEDLE BEARING 708, JR3050T | 1 |
| 212001-8 | N. BEARING 708, JR3000V | 1 | |
| 39 | 125423-2 | GEAR ASS'Y, BJR182Z | 1 |
| 40 | 212080-6 | NEEDLE BEARING 1012, BJR182Z | 1 |
| 41 | 253797-2 | F. WASHER 14,JR3030T | 1 |
| 42 | 232222-6 | LEAF SPRING (B), JR3050T | 1 |
| 43 | 345479-1 | SHOE GUIDE, JR3050T | 1 |
| 44 | 265165-7 | TORX C.S.H.SCREW M6X16,JR3050T | 1 |
| 45 | 266041-8 | TAPPING SCREW, FLANGE 5X25, 5177B | 4 |
| 54 | 154812-4 | GEAR HOUSING CPL., BJR181 | 1 |
| 55 | 961052-5 | RETAINING RING S-12, LS1016L | 1 |
| 56 | 210102-6 | BALL BEARING 6001DDW, JR3050T | 1 |
| 57 | 961016-9 | STOP RING E-10, BJR182 | 1 |
| 58 | 911225-0 | PAN HEAD SCREW M5X16, JR3050T | 2 |
| 59 | 285726-7 | BEARING RETAINER 63, BJR182Z | 1 |
| 60 | 241869-5 | FAN 55, 5621DWA | 1 |
| 61 | 519176-7 | ARMATURE ASS'Y 18V, BJR181 | 1 |
| 62 | 210062-2 | BALL BEARING 607ZZ, 9550H | 1 |
| 63 | 450176-7 | BAFFLE PLATE, BJR182Z | 1 |
| 638571-3 | YOKE UNIT, BJR182Z | 1 | |
| 65 | 158391-4 | MOTOR HOUSING CPL., BJR182Z | 1 |
| 66 | 266292-3 | TAPPING SCREW 4X65, 5402NA | 2 |
| 67 | 643829-7 | HOLDER CAP, BJR182Z | 2 |
| 68 | CB441 | CARBON BRUSH SET, 195022-4 | 1 |
| 195022-4 | CARBON BRUSH SET, 195022-4 | 1 | |
| 194435-6 | CARBON BRUSH SET CB-441, BJR181 | 1 | |
| 69 | 643827-1 | BRUSH HOLDER, BJR182Z | 1 |
| 70 | 864064-6 | NAME PLATE, BJR182 | 1 |
| 71 | 187208-4 | HANDLE SET, BJR182Z | 1 |
| 188366-9 | HANDLE SET, BJR182Z | 1 | |
| 72 | 643859-8 | TERMINAL, LXPH03 | 1 |
| 643838-6 | TERMINAL, BDF451 | 1 | |
| 643812-4 | TERMINAL, BDA350 | 1 | |
| 74 | 650648-4 | SWITCH, BJR182Z | 1 |
| 650595-9 | SWITCH, BJR182Z | 1 | |
| 76 | 450177-5 | LOCK OFF BUTTON, BJR182Z | 1 |
| 78 | 643826-3 | BRUSH HOLDER, BJR182Z | 1 |
| 79 | 911006-2 | P.H. SCREW M3X8, LXSF01 | 1 |
| 80 | 689116-0 | HEAT SINK, BJR240SH | 1 |
| 81 | 266326-2 | TAPPING SCREW PT 4X18, 5007MG | 6 |
| 82 | 187208-4 | HANDLE SET, BJR182Z | 1 |
| 188366-9 | HANDLE SET, BJR182Z | 1 | |
| 194502-7 | N/A | 1 | |
| 194068-7 | RECIPRO SAW BLADE SET, BJR182Z | 1 |
