Instructions for MUQI models including: MQ-13, MQ-13 Bluetooth Speaker, Bluetooth Speaker, Speaker
MQ-13 User Guide (PDF) MUQI MUQI MUQI,Bluetooth,Speaker,,Portable,Bluetooth,Speakers,Wireless,,IPX7,Waterproof,Shower,Speaker,,10W,Loud,Stereo,Sound,,12H,Playtime,TWS,Dual,Pairing,for,Home,Outdoors,B0B3WPPBZ8,B09YNLL7BJ,B09YNNHJR5
MUQI Bluetooth Speaker, IPX7 Waterproof Portable Wireless Speaker with 24H Playtime 10W Stereo Sound 66ft Bluetooth Range Dual Pairing for Outdoor, Travel, Home : Electronics
MQ-13 User Guide (PDF) MUQI MUQI MUQI,Bluetooth,Speaker,IPX7,Waterproof,Portable,Wireless,Speaker,with,24H,Playtime,10W,Stereo,Sound,66ft,Bluetooth,Range,Dual,Pairing,for,Outdoor,Travel,Home,B0B3WPPBZ8,B09YNLL7BJ
Thank you for purchasing the MUQI MQ-13 Wireless Speaker. Please read this user manual carefully and keep it for future reference. If you need any assistance, please contact our support team with your product model number and Amazon order number. Package Contents Wireless Speaker USB-A to C Cable 3.5mm Audio Cable User Manual Product Diagram Volume - / Previous Track Power Button - 01 - Multi-Function Button Volume + / Next Track USB-A to C Charging Port Audio Input - 02 - Specifications Model Technology Audio Output Power Frequency Response Signal-to-Noise Ratio Input Charging Time Battery Life Battery Type Operating Range Dimensions Weight MQ-13 A2DP V1.3, AVRCP V1.6, GAVDP V1.3, HFP V1.7, HID V1.1, IOPT, SPP V1.2 2 × 5W 80Hz - 20KHz 65dB DC 5V 3 hours 28 hours (50% volume) Li-ion (2200mAh) Up to 33ft / 10m L 175mm × W 50mm × H 67mm 360±20g - 03 - Getting Started Charging the Speaker Fully charge the speaker before first use. Connect one end of the USB-A to C cable to the charging input port of the MQ-13 and the other end to a USB charger or charging port to charge. The LED indicator will be solid red whilst charging and turn off when fully charged. Charging takes about 3 hours. Controls & LED Indicator AUX Mode Functions Turn speaker on / off Adjust volume Play or pause Instructions Press and hold the power button for 2 seconds Short-press volume + / - (synchronized with the volume of the iPhone, not Android) Press the multi-function button - 04 - BT Mode Functions Turn speaker on / off Switch mode Enter or exit TWS mode Play or pause Adjust volume Skip to next/previous track Answer or end the call Reject an incoming call Redial last-outgoing-called number Disconnect BT Instructions Press and hold the power button for 2 seconds Short-press the power button (between BT and AUX mode) Double-click the power button Short-press the multi-function button Short-press volume + / - (synchronized with the volume of the iPhone, not Android) Press and hold volume + / - for 2 seconds Short-press the multi-function button Press and hold the multi-function button for 2 seconds Double-click the multi-function button in stand-by Long-press the multi-function button - 05 - TWS Mode Functions Instructions Turn speaker on Turn speaker off Enter or exit TWS mode Play or pause Adjust volume Skip to next/previous track Answer or end the call Reject an incoming call Redial last-outgoing-called number Disconnect BT Press and hold the power button of both speakers for 2 seconds Press and hold the power button of any speaker for 2 seconds Double-click the power button of the home speaker Short-press the multi-function button of any of the two speakers Short-press the volume + / - of any of the two speakers (synchronized with the volume of the iPhone, not Android) Press and hold volume + / - of any of the two speakers Short-press the multi-function button of the home speaker Press and hold the multi-function button of the home speaker for 2 seconds Double-click the multi-function button of the home speaker in stand-by Press and hold the multi-function button of any of the two speakers for 2 seconds - 06 - Power On / Off Press and hold the power button for 2 seconds to turn on/off the speaker Pairing 1. When you turn on the speaker, it will automatically enter pairing mode 2. Activate the pairing function on your phone and select "MUQI MQ-13" 3. If a code or pin is required for pairing, enter "0000" as the default code 4. When successfully paired, you will hear a tone Note If you want to use another device to connect to MQ-13, please press and hold the multi-function button for 2 seconds to disconnect MQ-13 from the current device. Repeat the previous "pairing" steps When you turn the speaker on, it will automatically reconnect to the last-paired device or enter pairing mode if no paired device is found When the speaker is paused, or there is no Bluetooth connection, the speaker will automatically shut down after 10 minutes - 07 - If the speaker or connected device exceeds the operating range, the speaker will disconnect. The connection to the last successfully connected device will be re-established once you re-enter the wireless range within 10 minutes. To connect to other devices, repeat the previous "pairing" steps Playing Audio via Audio Input Connection Connect the MQ-13 to your PC, laptop, or other devices with the audio output port using the included 3.5mm audio cable. If the two speakers are in TWS mode, please connect the home speaker to the device you need using the included 3.5mm audio cable Note The speaker will disconnect from your phone or other paired devices when an audio cable is plugged into the audio input jack. Short-press the power button to switch back to BT mode - 08 - When playing audio using the audio input jack, press the volume + / - to adjust the volume and short-press the multi-function button to pause or resume. Next/previous track control on the speaker is disabled in audio input mode For some computers, you may need to access the audio control panel to manually set the speaker as the default audio device TWS Mode 1. Turn on two MQ-13 speakers at the same time, double-click the power button of one of the speakers to automatically enter the TWS pairing mode, a tone will be heard every three seconds 2. During the TWS pairing process, double-click the power button to cancel the TWS pairing. If the TWS pairing exceeds 60 seconds and the TWS pairing is not successful, it will automatically return to the normal BT mode 3. After the TWS pairing is successful, one of the LED lights of the two speakers is always on (this is the satellite) and the other is flashing (this is the home), and the TWS pairing success tone is the same as the BT connection success tone - 09 - 4. Activate the pairing function on your phone or other compatible device and select "MQ-13" 5. If a code or pin is required for pairing, enter "0000" 6. When successfully paired, you will hear a tone Note When the phone is connected to the Bluetooth of one of the speakers first, you need to double-click the power button of the speaker connected to the phone to enter the TWS pairing mode After the TWS pairing is successful, double-click the power button of one of the speakers to automatically exit the TWS pairing mode, and the BT connection between the home speaker and phone will not disconnect. Double-click the power button of the home speaker to enter TWS pairing mode - 10 - If the Bluetooth of the two speakers and the mobile phone is connected successfully, cancel the Bluetooth connection between one of the speakers and the mobile phone. Double-click the speaker that is successfully connected to the phone to enter the TWS pairing mode In TWS mode, directly press and hold the power button for 2 seconds to turn off, and the MQ-13 TWS will automatically connect back after the power is back on. If you double-click the power button to disconnect the TWS pairing, the TWS will need to be manually connected if you turn the device off If the two speakers or connected device exceeds the operating range, the speaker will disconnect. The connection to the last successfully connected device will be re-established once you re-enter the wireless range within 10 minutes. To connect to other devices, repeat the previous "pairing" steps - 11 - FAQ The TWS pairing is unsuccessful? Please check if the phone is connected to the Bluetooth of the two speakers at the same time. If yes, please long press the multi-function button of any of the two speakers to disconnect any speaker BT from the phone. Double-click the power button of the speaker that is connected to the phone to enter TWS pairing mode. If not, please double-click the power button of both speakers to enter TWS pairing mode. From TWS mode to AUX mode? Connect the home speaker to the required equipment with an audio cable. Press the power button to switch back t o Bluetooth mode. - 12 - Product Care & Use Keep away from extreme heat and strong magnetic fields Do not use this speaker at high volume for extended periods, as this may cause permanent hearing damage or hearing loss Warranty & Customer Support For questions, support, or warranty claims, contact us at the address below that corresponds with your region. Please include your Amazon order number and product model number E-mail: sales@szmuqi.com *Please note, MUQI can only provide after-sales service for products purchased directly from MUQI. If you have purchased from a different seller, please contact them directly for service or warranty issues. - 13 -Adobe PDF library 15.00 Adobe Illustrator(R) 17.0