Manuals+

Trademarks

FOXWELL is the trademark of Shenzhen Foxwell Technology Co., Ltd. All other marks are trademarks or registered trademarks of their respective holders.

Copyright Information

©2024 Shenzhen Foxwell Technology Co., Ltd. All rights reserved.

Disclaimer

The information, specifications and illustrations in this manual are based on the latest information available at the time of printing. Foxwell reserves the right to make changes at any time without notice.

Visit our website at www.foxwelltech.us

For Technical Assistance, send us email at support@foxwelltech.com

One-Year Limited Warranty

Subject to the conditions of this limited warranty, Shenzhen Foxwell Technology Co., Ltd ("FOXWELL") warrants its customer that this product is free of defects in material and workmanship at the time of its original purchase for a subsequent period of one (1) year.

In the event this product fails to operate under normal use, during the warranty period, due to defects in materials and workmanship, FOXWELL will, at its sole option, either repair or replace the product in accordance with the terms and conditions stipulated herein.

Terms and Conditions

  1. If FOXWELL repairs or replaces the product, the repaired or replaced product shall be warranted for the remaining time of the original warranty period. No charge will be made to the customer for replacement parts or labor charges incurred by FOXWELL in repairing or replacing the defective parts.
  2. The customer shall have no coverage or benefits under this limited warranty if any of the following conditions are applicable:
    • a) The product has been subjected to abnormal use, abnormal conditions, improper storage, exposure to moisture or dampness, unauthorized modifications, unauthorized repair, misuse, neglect, abuse, accident, alteration, improper installation, or other acts which are not the fault of FOXWELL, including damage caused by shipping.
    • b) The Product has been damaged from external causes such as collision with an object, or from fire, flooding, sand, dirt, windstorm, lightning, earthquake or damage from exposure to weather conditions, an Act of God, or battery leakage, theft, blown fuse, improper use of any electrical source, or the product was used in combination or connection with other product, attachments, supplies or consumables not manufactured or distributed by FOXWELL.
  3. The customer shall bear the cost of shipping the product to FOXWELL. And FOXWELL shall bear the cost of shipping the product back to the customer after the completion of service under this limited warranty.
  4. FOXWELL does not warrant uninterrupted or error-free operation of the product. If a problem develops during the limited warranty period, the consumer shall take the following step-by-step procedure:
    • a) The customer shall return the product to the place of purchase for repair or replacement processing, contact your local FOXWELL distributor or visit our website www.foxwelltech.us to get further information.
    • b) The customer shall include a return address, daytime phone number and/or fax number, complete description of the problem and original invoice specifying date of purchase and serial number.
    • c) The customer will be billed for any parts or labor charges not covered by this limited warranty.
    • d) FOXWELL will repair the Product under the limited warranty within 30 days after receipt of the product. If FOXWELL cannot perform repairs covered under this limited warranty within 30 days, or after a reasonable number of attempts to repair the same defect, FOXWELL at its option, will provide a replacement product or refund the purchase price of the product less a reasonable amount for usage.
    • e) If the product is returned during the limited warranty period, but the problem with the product is not covered under the terms and conditions of this limited warranty, the customer will be notified and given an estimate of the charges the customer must pay to have the product repaired, with all shipping charges billed to the customer. If the estimate is refused, the product will be returned freight collect. If the product is returned after the expiration of the limited warranty period, FOXWELL' normal service policies shall apply and the customer will be responsible for all shipping charges.
  5. ANY IMPLIED WARRANTY OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR USE, SHALL BE LIMITED TO THE DURATION OF THE FOREGOING LIMITED WRITTEN WARRANTY. OTHERWISE, THE FOREGOING LIMITED WARRANTY IS THE CONSUMER'S SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. FOXWELL SHALL NOT BE LIABLE FOR SPECIAL, INCIDENTAL, PUNITIVE OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LOSS OF ANTICIPATED BENEFITS OR PROFITS, LOSS OF SAVINGS OR REVENUE, LOSS OF DATA, PUNITIVE DAMAGES, LOSS OF USE OF THE PRODUCT OR ANY ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OF ANY SUBSTITUTE EQUIPMENT OR FACILITIES, DOWNTIME, THE CLAIMS OF ANY THIRD PARTIES, INCLUDING CUSTOMERS, AND INJURY TO PROPERTY, RESULTING FROM THE PURC HASE OR USE OF THE PRODUCT OR ARISING FROM BREACH OF THE WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, STRICT TORT, OR ANY OTHER LEGAL OR EQUITABLE THEORY, EVEN IF FOXWELL KNEW OF THE LIKELIHOOD OF SUCH DAMAGES. FOXWELL SHALL NOT BE LIABLE FOR DELAY IN RENDERING SERVICE UNDER THE LIMITED WARRANTY, OR LOSS OF USE DURING THE PERIOD THAT THE PRODUCT IS BEING REPAIRED.
  6. Some states do not allow limitation of how long an implied warranty lasts, so the one-year warranty limitation may not apply to you (the Consumer). Some states do not allow the exclusion or limitation of incidental and consequential damages, so certain of the above limitations or exclusions may not apply to you (the Consumer). This limited warranty gives the Consumer specific legal rights and the Consumer may also have other rights which vary from state to state.

Safety Information

For your own safety and the safety of others, and to prevent damage to the equipment and vehicles, read this manual thoroughly before operating your scanner. The safety messages presented below and throughout this user's manual are reminders to the operator to exercise extreme care when using this device. Always refer to and follow safety messages and test procedures provided by vehicle manufacturer. Read, understand and follow all safety messages and instructions in this manual.

Safety Message Conventions Used

We provide safety messages to help prevent personal injury and equipment damage. Below are signal words we used to indicate the hazard level in a condition.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury to the operator or to bystanders.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury to the operator or to bystanders.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in moderate or minor injury to the operator or to bystanders.

Important Safety Instructions

And always use your scanner as described in the user's manual, and follow all safety messages.

1 Using This Manual

We provide tool usage instructions in this manual. Below is the conventions we used in the manual.

1.1 Bold Text

Bold text is used to highlight selectable items such as buttons and menu options.

Example: Press the ENTER button to select.

1.2 Symbols and Icons

1.2.1 Solid Spot

Operation tips and lists that apply to specific tool are introduced by a solid spot .

Example: When Settings is selected, a menu that lists all available options displays. Menu options include:

1.2.2 Arrow Icon

An arrow icon indicates a procedure.

Example: To change menu language:

  1. Scroll with the arrow keys to highlight Language on the menu.
  2. Press the ENTER button to select.

1.2.3 Note and Important Message

Note

A NOTE provides helpful information such as additional explanations, tips, and comments.

Example:

NOTE Test results do not necessarily indicate a faulty component or system.

Important

IMPORTANT indicates a situation which, if not avoided, may result in damage to the test equipment or vehicle.

Example:

IMPORTANT Do not soak keypad as water might find its way into the scanner.

2 Introductions

This series of scanners from Foxwell are innovative diagnostic tools for most vehicles on the road today.

With the tool properly connected to the vehicle's data link connector (DLC), you can use the scanner to read diagnostic trouble codes and view “live” data readings from a variety of control systems. You can also save “recordings” of the data readings, and print stored information.

2.1 Scanner Descriptions

This section illustrates external features, ports and connectors of the scanner.

Figure 2-1 Front View: This diagram shows the front of the Foxwell scanner, labeling the Diagnostic Port (1), LCD Display (2), Function Keys (3), Direction Keys (4), OK Key (5), BACK Key (6), HELP Key (7), and USB Port (8).

IMPORTANT: Do not use solvents such as alcohol to clean keypad or display. Use a mild nonabrasive detergent and a soft cotton cloth.

2.2 Accessory Descriptions

This section lists the accessories that go with the scanner. If you find any of the following items missing from your package, contact your local dealer for assistance.

2.3 Technical Specifications

Display: Backlit, 4.3" TFT color display

Working Temperature: 0 to 60 °C (32 to 140°F)

Storage Temperature: -20 to 70 °C (-4 to 158°F)

Power Supply: 8-18V vehicle power and 3.3V USB power

Dimensions: (L*W*H): 200*110*30mm

Weight: 1.8 Kgs

3 Getting Started

This section describes how to provide power to the scanner, provides brief introductions of applications loaded on the scanner and display screen layout and illustrates how to input text and numbers with the scan tool.

3.1 Providing Power to Scanner

Before using the scanner, make sure to provide power to the scanner.

The unit operates on any of the following sources:

3.1.1 Connecting to Vehicle Power

The scanner normally powers on whenever it is connected to the data link connector (DLC).

To connect to vehicle power:

  1. Locate the data link connector (DLC). The DLC is generally located under the dash on the driver side of the vehicle.
  2. Attached the Diagnostic cable to the scanner and tighten the captive screws to ensure good connection.
  3. Connect a correct adapter to the data cable according to the vehicle being serviced and plug it into the vehicle DLC.
  4. Switch the ignition key to the ON position.
  5. The scanner automatically boots up.

IMPORTANT: Never try to provide power for the scan tool from USB connection when the scan tool is communicating with a vehicle.

3.1.2 Connecting to Computer with USB Cable

The scan tool also receives power through the USB port when it is connected to a computer for software updates and printing of data.

To connect to computer:

  1. Connect the scanner to a computer with the USB cable provided.

3.2 Application Overview

When the scan tool boots up, the Home screen opens. This screen shows all applications loaded on the unit. The available vehicle applications may vary depending on software configuration.

Figure 3-1 Sample Home Screen: This image displays the main menu of the scanner with icons for Auto VIN, OBDII/EOBD, Diagnostic, Maintenance, History, Update, Settings, and Data Manager.

3.3 Input Dialog Box

This section illustrates how to use the scan tool to input letters and numbers, such as VIN number, channel number, test values and DTC number. Typically, you may be required to input letters or numbers when you are doing any of the following operations:

The scan tool provides 4 different types of keyboard to meet your specific needs. Depending on the needs of text entry, it automatically shows the most suitable keypad:

To input text with the scan tool:

  1. When you are requested to input text, press the function key Keyboard.

Figure 3-2 Sample Input Text Screen: Shows a text input field with navigation buttons like Back(F1), Keyboard(F2), Completed(F3).

Figure 3-3 Sample Numeric Keyboard Screen: Displays a virtual keyboard layout with alphanumeric keys, numbers, and symbols, along with navigation keys like Cursor Forward(F1), Backspace(F2), Completed(F3).

  1. To delete a letter or number, use the function key Cursor Forward to move the cursor to it and then press the Backspace button.
  2. When finished the entry, press Completed key to continue.

4 Vehicle Identification

This section illustrates how to use the scanner to identify the specifications of the vehicle under test. The vehicle identification information presented is provided by the ECM of the vehicle being tested. Therefore, certain attributes of the test vehicle must be entered into the scan tool to ensure the data displays correctly. The vehicle identification sequence is menu driven, you simply follow the screen prompts and make a series of choices. Each selection you make advances you to the next screen. Exact procedures may vary somewhat by vehicle. It typically identifies a vehicle by any of the following means:

NOTE: Not all identification options listed above are applicable to all vehicles. Available options may vary by vehicle manufacturer.

4.1 Auto VIN

Auto VIN is a shortcut for VIN reading menu which typically includes following options:

4.1.1 Automatic VIN Acquisition

Automatic VIN Acquisition allows to identify a vehicle by automatically reading the vehicle identification number (VIN).

To identify a vehicle automatic VIN reading:

  1. Scroll with the arrow keys to highlight Auto VIN from the main menu and press the ENTER key.

Figure 4-1 Sample Main Menu Screen: Shows the main menu with icons for VIN, Diagnostic, Maintenance, OBD II, History, Update, Settings, Data Manager.

  1. Select Automatic VIN Acquisition from the menu, and press the ENTER key.

Figure 4-2 Sample VIN Reading Screen: Displays a menu with options '1 Automatic Read' and '2 Manual Entry' under the AUTO VIN section.

  1. The scan tool starts to communicate with the vehicle and read the Vehicle Specification or VIN Code automatically.

Figure 4-3 Sample Automatic VIN Reading Screen: Shows vehicle information including VIN, Year, Vehicle type, Product make, Vehicle name, Engine type, and Body style, with 'No' and 'Yes' options.

  1. Answer YES if the Vehicle Specification or VIN code is correct and a menu of controller selection displays. Answer NO if it is incorrect, and you are required to enter the correct VIN number manually.

Figure 4-4 Sample Manual VIN Entry Screen: Displays a virtual keyboard for manual VIN entry, similar to Figure 3-3.

  1. If it takes too long to get the VIN code, press Cancel to stop and input the VIN manually. Or if failed to identify the VIN, please input the VIN manually or click Cancel to quit.

Figure 4-5 Sample Manual Entry Screen: Shows a manual entry screen with a virtual keyboard, similar to Figure 4-4.

4.1.2 Manual VIN Entry

Manual VIN Entry identifies a vehicle by manually inputting a 17-digit VIN code.

To identify a vehicle by manual VIN entry:

  1. Scroll with the arrow keys to highlight Auto VIN from the main menu and press the ENTER key.

Figure 4-6 Sample Main Menu Screen: Shows the main menu with icons for VIN, Diagnostic, Maintenance, OBD II, History, Update, Settings, Data Manager.

  1. Select Manually input VIN from the menu, and press the ENTER key.

Figure 4-7 Sample VIN Reading Screen: Displays a menu with options '1 Automatic Read' and '2 Manual Entry' under the AUTO VIN section.

  1. Press the function key Keyboard and a virtual keyboard opens for VIN entry.

Figure 4-8 Sample Manual VIN Entry Screen: Displays a virtual keyboard for manual VIN entry.

  1. Input a valid VIN code and use the function key Completed to confirm. The scan tool starts to identify the vehicle.

4.2 Manual Vehicle Selection

Select vehicle brand you are to test, and two ways of getting to the diagnostic operations are available:

4.2.1 Smart VIN

Smart VIN allows to identify a vehicle by automatically reading the vehicle identification number (VIN).

To identify a vehicle by SmartVIN:

  1. Scroll with the arrow keys to highlight Diagnostic from main menu and press the ENTER key to start. If you have the application assigned to one of the function keys at the bottom of the screen, you can alternatively press the function key to start the application.

Figure 4-9 Sample Main Menu Screen: Shows the main menu with icons for VIN, Diagnostic, Maintenance, OBD II, History, Update, Settings, Data Manager.

  1. A screen with vehicle manufacturer areas displays. Select the area where the car brand is originated. A list of vehicle makes display.

Figure 4-10 Sample Vehicle Manufacturer Area Selection Screen: Shows regional selections for vehicle manufacturers (America, Asia, Europe, China).

  1. Select the vehicle manufacturer. A list of vehicle identification options displays.

Figure 4-11 Sample Vehicle Selection Screen: Displays a list of vehicle makes such as BUICK, CADILLAC, CHEVROLET, CHRYSLER, DODGE, FIATBRAZIL, FORD, GM.

  1. Select SmartVIN from the menu, and press the ENTER key.

Figure 4-12 Sample VIN Reading Screen: Shows a menu with options '1 SmartVIN' and '2 Manual Selection' under the Diagnosis section.

  1. The scan tool starts to communicate with the vehicle and read the Vehicle Specification or VIN Code automatically.

Figure 4-13 Sample Automatic VIN Reading Screen: Shows vehicle information including VIN, Year, Vehicle type, Product make, Vehicle name, Engine type, and Body style, with 'No' and 'Yes' options.

  1. Answer YES if the Vehicle Specification or VIN code is correct and a menu of controller selection displays. Answer NO if incorrect, and you are required to enter the correct VIN number manually.

Figure 4-14 Sample Manual VIN Entry Screen: Displays a virtual keyboard for manual VIN entry.

4.2.2 Manual Selection

Manual Selection identifies a vehicle by making several selections according to certain VIN characters, such as model year, and engine type.

To identify a vehicle by manual vehicle selection:

  1. Refer to step 1-3 of 4.2.1 SmartVIN.

Figure 4-15 Sample Manual Vehicle Selection Screen: Shows example screens for selecting vehicle details like model, year, and HVAC system, and confirming vehicle information.

  1. On each screen that appears, select the correct option and then press the ENTER key. Do this until the complete vehicle information is entered and the menu of controller selection displays.

5 Diagnostic Operations

This section illustrates how to use the scanner to read and clear diagnostic trouble codes, and view "live" data readings and ECU information on controllers installed on a variety of vehicles and also save “recordings” of the data readings.

5.1 Control Module Selection

When you completed the identification of vehicle, you have to identify the control modules installed in the vehicle. There are two ways to identify the controllers installed in a car:

5.1.1 Quick Scan

Quick Scan performs an automatic system test to determine which control modules are installed on the vehicle and provides diagnostic trouble codes (DTCs) overview. Depending on the number of control modules, it may take 10 minutes or longer to complete the test.

To perform an automatic system scan:

  1. Scroll with the arrow keys to highlight Quick Scan from the menu and press ENTER to start.

Figure 5-1 Sample Quick Scan Screen: Shows a menu with options '1 Quick Scan' and '2 Control Modules'.

  1. To pause the scan, press the function key corresponding with Pause on the screen.

Figure 5-2 Sample Quick Scan Screen: Shows a scan progress with detected faults for Engine controls, Engine cooling, Engine electrical, and Theft deterrent.

  1. At the end of successful automatic controller scan, a menu with a list of installed controllers together with their DTC overview displays.

Figure 5-3 Sample Quick Scan Screen: Displays a list of scanned control modules with fault status, including Engine controls, Engine cooling, Engine electrical, Theft deterrent, Instrument panel, and HVAC systems.

  1. If there is diagnostic trouble code(s) detected in a control unit, press the function key corresponding with Report on the screen to view details of code information. Or press the function key Erase to clear them.

Figure 5-4 Sample DTC Screen: Shows a report of detected trouble codes, listing codes and descriptions for Engine controls, Engine cooling, Engine electrical, and Theft deterrent.

  1. Press function key F1 to save the trouble code information.
  2. Select the system you would like to test, and press the ENTER key. When the scanner has established connection with the vehicle, the Function Menu displays.

Figure 5-5 Function Menu screen: Shows a list of functions for a selected system: 1 Trouble codes, 2 Freeze frame, 3 ECU Information, 4 Live data, 5 Active test, 6 Special functions.

5.1.2 Control Modules

Control Modules screen displays all controllers available on the vehicles. The controllers listed on the menu do not mean that they are installed on the vehicle.

To select a system for testing:

  1. Scroll with the arrow keys to highlight Control Modules from the menu and press the ENTER key. A controller menu displays.

Figure 5-6 Sample Control Module Screen: Shows a menu with options '1 Quick Scan' and '2 Control Modules'.

  1. Select the system you would like to test. When the scanner has established connection with the vehicle, the Control Module menu displays.

Figure 5-7 Sample Control Module Menu Screen: Displays a list of vehicle systems for testing, including Engine controls, Automatic transaxle, Engine cooling, Engine electrical, Body control module, Body rear end, Supplemental inflatable restraint.

5.2 Diagnostic Operations

After a system is selected and the scanner establishes communication with the vehicle, the Function Menu displays. The menu options may include:

NOTE: Not all function options listed above are applicable to all vehicles. Available options may vary by the year, model, and make of the test vehicle.

5.2.1 ECU Information

ECU Information screen displays the identification data of the control module under test, such as the control module identification string, the control module coding, and Work Shop Code.

To read ECU information:

  1. Select ECU Information from the menu and press the ENTER key.

Figure 5-8 Sample Function Menu Screen: Shows a list of functions for a selected system: 1 ECU Information, 2 Read Codes, 3 Clear Codes, 4 Live data.

  1. A screen with detailed information of the selected control module displays.

Figure 5-9 Sample ECU Information Screen: Displays ECU information including Vehicle VIN, Calibration ID, and Verification number.

  1. Press function key Save to store ECU information. Or use the [back] key to exit.

5.2.2 Read Codes

Read Codes menu lets you read trouble codes found in the control unit.

Typical code status include:

Present/Permanent/Current codes stored in a control module are used to help identify the cause of a trouble or troubles with a vehicle. These codes have occurred a specific number of times and indicate a problem that requires repair. Pending codes are also referred to as maturing codes that indicate intermittent faults. If the fault does not occur within a certain number of drive cycles (depending on vehicle), the code clears from memory. If a fault occurs a specific number of times, the code matures into a DTC and the MIL illuminates or blinks. History codes are also referred to as past codes that indicate intermittent DTCs that are not currently active.

To read codes from a vehicle:

  1. Scroll with the arrow keys to highlight Read Codes from Function Menu and press the ENTER key. A code list including code number and its description displays.

Figure 5-10 Sample Function Menu Screen: Shows a list of functions for a selected system: 1 ECU Information, 2 Read Codes, 3 Clear Codes, 4 Live data.

  1. Use the up and down arrow keys to scroll through data to select lines, and left and right arrow keys to scroll back and forth through different screens of data.

Figure 5-11 Sample Code Screen: Displays a list of Diagnostic Trouble Codes (DTCs) with their descriptions, such as P0010-00, P0107-00, P0122-00, P0223-00, P0230-00.

  1. Press function key Save to store DTC information. Press function key Freeze Frame to view freeze data.

Figure 5-12 Freeze Data screen: Shows freeze frame data parameters like Long term fuel trim, HO2S 1, HO2S 2, Ignition 1 signal, Spark, EVAP purge solenoid command, with their values.

Freeze Frame Data: a snapshot of critical vehicle operating conditions automatically recorded by the on-board computer at the time of the DTC set. It is a good function to help determine what caused the fault.

  1. Use left and right arrow keys to scroll back and forth through different screens of data.
  2. Press function key Save to store freeze frame information. Or use the BACK key to exit.

5.2.3 Clear Codes

Clear Codes menu lets you to clear all current and stored DTCs from a selected control module. Also it erases all temporary ECU information, including freeze frame. So make sure that the selected system is completely checked and serviced by technicians and no vital information will be lost before clearing codes.

NOTE:

To clear codes:

  1. Scroll with the arrow keys to highlight Clear Codes from Function Menu and press the ENTER key.

Figure 5-13 Sample Function Menu Screen: Shows a list of functions for a selected system: 1 ECU Information, 2 Read Codes, 3 Clear Codes, 4 Live data.

  1. Follow the on-screen instructions and answer questions about the vehicle being tested to complete the procedure.

Figure 5-14 Sample Clear Codes Screen: Prompts "DTCs and freeze data will be cleared! Are you sure to continue?" with 'No(F1)' and 'Yes(F3)' options.

  1. Check the codes again. If any codes remain, repeat the Clear Codes steps.

5.2.4 Live Data

Live Data menu lets you view and record real time PID data from a selected vehicle electronic control module.

Menu options typically include:

5.2.4.1 Complete List

Complete List menu lets you view all live PID data from a selected system.

To view live PID data:

  1. Scroll with the arrow keys to highlight Live Data from the menu and press the ENTER key.

Figure 5-15 Sample Function Menu Screen: Shows a list of functions for a selected system: 1 ECU Information, 2 Read Codes, 3 Clear Codes, 4 Live Data.

  1. Select the Complete List from the menu and press the ENTER key to display the data screen.

Figure 5-16 Sample Live Data Menu Screen: Shows a menu with options '1 All Data' and '2 Custom List' under the Live Data section.

  1. Scroll with the up and down arrow keys to highlight a line, and left and right arrow keys to scroll back and forth through different screens of data. Press function key Pause to suspend collecting data from the vehicle and use the Start key to resume collecting data. To record data to memory of the scanner, use the function key SAVE, and press Stop Saving to stop recording at any time.

Figure 5-17 Sample Live Data Screen: Displays live data parameters such as Engine Speed, Idle Control Setpoint, Sensor Supply 1, Sensor Supply 2, Pedal 1 Demand, Pedal 2 Demand, with their values and units.

  1. Use up and down arrow key to select line. If Graph is highlighted, it indicates graphing is available for the selected line. Press the function key Graph to display the PID graph.

Figure 5-18 Sample PID Graph Screen: Shows a line graph of 'Idle Control Setpoint' over time.

  1. Press the function key Multi-graphs to display two PID graphs in one screen. Press Single graph to view one plot.

Figure 5-19 Sample Two PID Graph Screen: Displays two PID graphs, one for 'Coolant Temp' and one for 'Throttle Angle'.

  1. Press the function key Merge Graph to display two PID plots in one coordinate to check how they affect each other.

Figure 5-20 Sample Merge Graph Screen: Displays two PID plots ('Coolant Temp' and 'Throttle Angle') overlaid on the same coordinate system.

  1. Press the Back key to return to the previous menu.

5.2.4.2 Custom List

Custom List menu lets you to minimize the number of PIDs on the data list and focus on any suspicious or symptom-specific data parameters.

To create a custom data list:

  1. Select Custom List from the menu and press the ENTER key.

Figure 5-21 Sample Live Data Menu Screen: Shows a menu with options '1 All Data' and '2 Custom List' under the Live Data section.

  1. The custom data selection screen displays. Scroll with the up and down arrow keys to highlight a line, press the ENTER key and then repeat the action to make more selections. To deselect an item, select it again and then press the ENTER key. Alternatively, use the function keys Select All and Deselect to select or deselect all items at once.

Figure 5-22 Sample Custom List Selection Screen: Shows a list of data parameters with checkboxes, allowing selection of specific parameters for display.

  1. When finished selection, use the function key OK to display selected items.

Figure 5-23 Sample Live Data Screen: Displays selected live data parameters with their values and units.

Maintenance

NOTE

NT614 Elite support

NT624 Elite support

NT644 Elite and NT634 supports all of the following service and maintenance operations.

6 Maintenance

This section gives brief instructions of the most commonly required service and maintenance operations. Typical service operation screens are a series of menu driven executive commands. Follow on-screen instructions to complete the operation.

Available service and maintenance options include:

To start a test:

  1. Scroll with the arrow keys to highlight Maintenance from the main menu and press the ENTER key. A list of available services display.

Figure 6-1 Sample Main Menu Screen: Shows the main menu with icons for VIN, Diagnostic, Maintenance, OBD II, History, Update, Settings, Data Manager.

  1. Select a service to test and press ENTER key to start.

Figure 6-2 Sample Maintenance Screen: Displays various maintenance functions like AFR ADAPTATION, REPLACE AIRBAG ECU MODULE, ABS SERVICE, BRT, CHANGE TIRE SIZE, CLUTCH ADAPTATION, CVT, DPF.

6.1 Oil Service Reset

Oil Light Reset menu allows you to reset the service lamps on the instrument cluster. The Service Indicator System is designed to alert the driver when the vehicle is due for a service.

Oil service reset methods are determined by the vehicle being tested.

6.2 Electronic Parking Brake

EPB Service menu allows you to perform the service and maintenance of brake systems, including deactivation and activation of the brake control system, bleeding brake fluid, opening and closing brake pads, and setting brakes after disc or pad replacement, on multiple brands of vehicles where electronic brake systems are fitted.

Some tests display a command to the operator. For example, if “Pressing Brake Pedal" displays, the operator has to press and hold the brake pedal and then continue. Actual tests vary by vehicle manufacturer, year, make.

Typical special test options include:

WARNING:

6.3 Battery Replacement (BRT)

BRT menu lets you to n to validate new battery, clear faults from the dashboard and display current battery details of the vehicle such as Audi, BMW, Citroen, Peugeot, Seat, Skoda, Volvo, VW and Ford.

  1. Replace the old battery with the new one. Ensure the key is not in the ignition.
  2. Connect the scanner to the vehicle's 16 pin Data Link Connector (DLC) with the diagnostic cable.
  3. Boost the device and select BRT; it will display all the vehicle makes available. Choose your vehicle make and follow the scanner instruction to start.

6.4 Diesel Particulate Filter (DPF) Regeneration

DPF Regeneration menu lets you perform the DPF cleaning to clear the blockage through continuous burning of the particulates captured in the DPF filter. When a DPF regeneration cycle is completed, the DPF light automatically goes off.

6.5 Throttle Body Alignment (TPS/TBA)

It's very common to see a customer pull into the shop with a Volkswagen or Audi that just will not idle correctly. One of the possible causes is that the throttle position is not known. When the motion range is not known, the ECU simply has no idea where to set the throttle. The ECU must know the full range of motion of the throttle in order for it to properly control the engine. Using the throttle position sensors in the throttle body, the ECU learns the full open and full closed positions through various states (idle, part throttle, WOT) known as a Throttle Body Alignment (TBA).

6.6 Steering Angle Sensor (SAS) Calibration

SAS Calibration menu let you perform calibration of the Steering Angle Sensor, which permanently stores the current steering wheel position as straight-ahead in the sensor EEPROM. On successful calibration of the sensor, its fault memory is automatically cleared.

6.7 Continuous Variable Transmission (CVT)

This function is used to reset the compensation code and initialize the ECT after a solenoid valve or valve body assembly has been replaced.

6.8 Gear Learning

The crankshaft position sensor learns crankshaft tooth machining tolerance and save to the computer to more accurately diagnose engine misfires. If tooth learning is not performed for a car equipped with Delphi engine, the MIL turns on after the engine is started. The diagnostic device detects the DTC P 1336 'tooth not learned'. In this case, you must the diagnostic device to perform tooth learning for the car. After tooth learning is successful, the MIL turns off.

After the engine ECU, crankshaft position sensor, or crankshaft flywheel is replaced, or the DTC 'tooth not learned' is present, tooth learning must be performed.

6.9 TPMS Relearn

After the tire pressure MIL turns on and maintenance is performed, the tire pressure resetting function must be performed to reset tire pressure and turn off the tire pressure MIL.

6.10 Injector Coding

Write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder so as to more accurately control or correct cylinder injection quantity. After the ECU or injector is replaced, injector code of each cylinder must be confirmed or re-coded so that the cylinder can better identify injectors to accurately control fuel injection.

7 OBDII/EOBD Operations

OBDII/EOBD menu lets you access all OBD service modes. According to ISO 9141-2, ISO 14230-4, and SAE J1850 standards, the OBD application is divided into several sub programs, called 'Service $xx'. Below is a list of OBD diagnostic services:

When OBDII/EOBD application is selected from Home screen, the scanner starts to detect the communication protocol automatically. Once the connection has established, a menu that lists all of the tests available on the identified vehicle displays. Menu options typically include:

NOTE: Not all function options listed above are applicable to all vehicles. Available options may vary by the year, model, and make of the test vehicle. A “Not supported the mode!" message displays if the option is not applicable to the vehicle under test.

8 System Setup

This section illustrates how to program the scanner to meet your specific needs.

When Settings is selected, a menu with available service options displays. Menu options typically include:

8.1 Select Language

Selecting Language opens a screen that allows you to choose system language. The scan tool is set to display English menus by default.

To configure system language:

  1. Scroll with the arrow keys to highlight Language from Settings menu and press ENTER key.

Figure 8-1 Sample Settings Screen: Shows the Settings menu with icons for WIFI, Language, Unit, Uninstall, Shortcut, Display Test, Keypad Test, About.

  1. Press left and right arrow key select a language and press the ENTER key to confirm. Press the Back key to exit and return.

Figure 8-2 Sample Language Selection Screen: Displays language options including Chinese (中文), German (Deutsch), English, Spanish (Español), French (Français), Traditional Chinese (繁體中文), Hungarian (Magyar), Italian (Italiana).

8.2 Change Units

Selecting Unit opens a dialog box that allows you to choose units of measure.

To change the unit setup:

  1. Scroll with the arrow keys to highlight Units from Settings menu and press the ENTER key.

Figure 8-3 Sample Settings Screen: Shows the Settings menu with icons for WIFI, Language, Unit, Uninstall, Shortcut, Display Test, Keypad Test, About.

  1. Press the up and down arrow key select an item and press the ENTER key to save and return.

Figure 8-4 Sample Unit Selection Screen: Shows a Unit selection dialog with options 'Metric' and 'Imperial'.

8.3 Configure Shortcut Keys

Selecting Shortcuts option lets you to change the functionality of the shortcut buttons.

To assign a function to a shortcut button:

  1. Scroll with the arrow keys to highlight Shortcuts from Settings menu and press the ENTER key. A screen with available shortcut keys displays.

Figure 8-5 Sample Settings screen: Shows the Settings menu with icons for WIFI, Language, Unit, Uninstall, Shortcut, Display Test, Keypad Test, About.

  1. Press the up and down arrow key select a shortcut key and press the ENTER key. A screen with a list of loaded applications displays.

Figure 8-6 Sample Shortcuts Screen: Shows options to 'Edit ShortCuts F1 Function', 'Edit ShortCuts F2 Function', 'Edit ShortCuts F3 Function'.

  1. Scroll with the arrow keys to highlight an application and press the ENTER key to assign the application to the shortcut key.

Figure 8-7 Sample Shortcuts Screen: Displays a list of vehicle makes/models for assignment to shortcut keys, such as ABARTH, ACURA, ALFA, ASTONMARTIN, AUDI, BAICHUANSU, BAICMOTOR, BAICSENOVA.

8.4 Display Test

Selecting Display Test option opens a screen that allows you to check the functionality of the display.

To test the display:

  1. Scroll with the arrow keys to highlight Display Test from Settings menu and press the ENTER key to start test. Check if there are any missing spots in the LCD screen.

Figure 8-8 Sample LCD Test Screen: Shows a full-screen display of colored pixels, likely for testing dead pixels or screen uniformity.

  1. To quit the test, press the Back key.

8.5 Keypad Test

Selecting Keypad Test option opens a screen that allows you to check the functionality of the keypad.

To test the keypad:

  1. Scroll with the arrow keys to highlight Keypad Test from Settings menu and press ENTER key.

Figure 8-9 Sample Settings Screen: Shows the Settings menu with icons for WIFI, Language, Unit, Uninstall, Shortcut, Display Test, Keypad Test, About.

  1. Press any key to start test. The virtue key corresponding with the key you pressed will be highlighted on the screen if it works correctly.

Figure 8-10 Sample Keypad Test Screen: Shows the scanner's keypad layout with keys highlighted as they are pressed, indicating functionality.

  1. To quit the test, press Back key twice.

8.6 Tool Information

Selecting About option opens a screen that shows information about your scan tool, such as serial number, which may be required for product registration.

To view information of your scan tool:

  1. Scroll with the arrow keys to highlight About from Settings menu and press the ENTER key.

Figure 8-11 Sample Settings Screen: Shows the Settings menu with icons for WIFI, Language, Unit, Uninstall, Shortcut, Display Test, Keypad Test, About.

  1. A screen with detailed information of the scanner displays.

Figure 8-12 Sample Tool Information Screen: Displays scanner information including Home Version, BOOT Version, Serial Number, and Copyright information.

  1. Press the Back key to exit.

9 Update

To update scanner, you need the following tools:

NOTE:

Figure 9-1 Sample WIFI Screen: Shows the Settings menu with icons, highlighting the WIFI option.

  1. Enter Update and select an available WIFI to connect.

Figure 9-2 Sample WIFI Selection Screen: Displays a list of available WIFI networks (FOXWELL_GEUST, FOXWELL, 1024, ChinaNet-zVmL, CMW-AP, ChinaNet-b6pl) with options to Edit(F1) and Refresh(F3).

  1. In the Update, click the check box(es) in front of the software(s) you wish to update and then click the Update Select button to download.

Figure 9-3 Sample Upgrade Check Screen: Shows a list of software packages (LEXUS, SCINO, TOYOTA, APP, FOX200, Common Text Library) with version numbers, sizes, and status (Ready), and options to Select All(F1) and Update(F3).

  1. When all the items are updated, an "All software downloads are successfully installed!" message displays.

Figure 9-4 Sample Update Completed Screen: Displays a confirmation message "All software are downloaded and installed successfully!"

10 Uninstall

This option allows you to uninstall the vehicle software installed in the scanner.

To uninstall a vehicle software:

  1. Enter Settings application on home screen.

Figure 10-4 Sample Uninstall Vehicle Software Screen: Shows the Settings menu with icons, highlighting the Uninstall option.

  1. Select the Uninstall Vehicle Software option on the option list.
  1. Choose the vehicle software you want to delete or choose Select All to Uninstall.

Figure 10-5 Sample Uninstall Vehicle Software Screen: Displays a list of vehicle software packages (ABARTH, ACC, ACLEARN, ACURA, ADAS, ADBLUE) with their sizes, and options to Select All(F1) and Uninstall(F3).

PDF preview unavailable. Download the PDF instead.

NT650Pro User s Manual ?v=1753877760 WPS 文字

Related Documents

Preview FOXWELL NT6X4Elite Series User's Manual - Automotive Diagnostic Tool
Comprehensive user manual for the FOXWELL NT6X4Elite Series automotive diagnostic scanner. Learn how to perform vehicle diagnostics, maintenance services, and software updates with detailed instructions and safety guidelines.
Preview FOXWELL NT6X4Elite Series User Manual: Automotive Diagnostic Scan Tool Guide
Comprehensive user manual for the FOXWELL NT6X4Elite Series automotive diagnostic scan tool. Learn about vehicle identification, DTC reading, live data, maintenance functions, and software updates. Get expert diagnostic capabilities.
Preview Foxwell NT520 Pro Multi-system Scanner User Manual
Explore the comprehensive user manual for the Foxwell NT520 Pro Multi-system Scanner. This guide provides detailed instructions on vehicle diagnostics, service functions, system setup, updates, and more for professional automotive repair.
Preview FOXWELL NT510 Multi-system Scanner User Manual
Comprehensive user manual for the FOXWELL NT510 Multi-system Scanner, detailing its features, operations, safety information, and troubleshooting for automotive diagnostics. Covers vehicle identification, system diagnostics, bi-directional tests, OBDII/EOBD functions, and service/maintenance procedures.
Preview FOXWELL NT650Elite Multi-Application Service Tool User Manual
Comprehensive user manual for the FOXWELL NT650Elite Multi-Application Service Tool, covering warranty, safety, setup, vehicle identification, diagnostic operations, maintenance, and system settings. Includes detailed instructions and specifications.
Preview Foxwell NT680 Series User's Manual: Comprehensive Guide to Automotive Diagnostics
Detailed user manual for the Foxwell NT680 Series automotive diagnostic scanner, covering setup, vehicle identification, diagnostic operations, maintenance, and system settings. Includes warranty information and safety guidelines.
Preview FOXWELL NT650Elite Multi-Application Service Tool Manual - User Guide and Diagnostics
User manual for the FOXWELL NT650Elite Multi-Application Service Tool. This guide details safety, operation, diagnostics (ABS, SRS), maintenance (DPF, EPB, BRT), and update procedures for automotive professionals.
Preview FOXWELL NT630 Elite ABS & Airbag Reset Tool User Manual | Diagnostics & Guide
Explore the comprehensive user manual for the FOXWELL NT630 Elite ABS & Airbag Reset Tool. This guide details features, setup, diagnostic operations, OBDII/EOBD functions, system configuration, software updates, and result printing for effective vehicle diagnostics.