Instruction Manual for Shenzhen Unisheen Technology models including: BM3380G-H, BM3380GH, 2A442-BM3380G-H, 2A442BM3380GH, H.265 HEVC, H.264 AVC, MPGE4, HEVC H.265 MPGE4 FHD Video Audio Live Encoder
Shenzhen Unisheen Technology Co.,LTD. BM3380G-H Video Encoder 2A442-BM3380G-H 2A442BM3380GH bm3380g h
5 ago 2023 — Instructions: in terms of IP address of the equipment, the factory default is. 192.168.1.168. ... rtmp://a.rtmp.youtube.com/live2/87gg-dtd0-7atc-8zwu.
File Info : application/pdf, 17 Pages, 489.15KB
DocumentDocumentH.265 HEVC/H.264 AVC/MPGE4 FHD Video/Audio Live Encoder Manual 1.Interface Power: DC 9-12V 1A ANT: HG WIFI HDMI IN: HDMI Video Input Port Power: Power Light(Red) Reset:Recovery to Default setting LAN: Lan Status Light(Green) LAN: 1000M Ethernet Port Video: Video Signal Light(Blue) WIFI:it is AP when it is blink,it is connected it is always bright. Instructions A. Power ----9-12 V/DC 1A; B. Reset----- it is used to reset the equipment; after the equipment is started, press the button for 10 seconds, the equipment IP is recovery to the default IP, 192.168.1.168. C. Video input --- it is used to input high-definition HDMI D. LAN ---- 100M or 1000M Ethernet connection. 2.Specification Input Video HDMI resolution ratio Encoding Bitrate 1.4 HDMI HDCP 1920x1200_60P,1920×1080_50/60P,1920×1080_50/60i, 1280×720_50/60p 720x576i/p 720x480i/p. H.265 HEVC or H.264 AVC Profile 4.2 16kbit/s32Mbit/s Bitrate control GOP CBR/VBR Adjustable Audio: Encoding Re-Sampling rate Bitrate Sampling precision Bitrate System: Network Stream Configuration interface Updating General Size Net Weight Temperature range Power supply Power consumption AAC AAC+ AAC++ MP3 MP2 AC3 G.711A/U 44100/48000 48K64K96K128K160K192K256K 24 bit 64Kb/s~384Kb/s 100M/1000M Base-T Ethernet /WIFI 2.4G UTP,HTTP,FLV,HLS,RTSP,RTMP RTP UDP(Multicast,Unicast) and ONVIF WEB operation interface or CGI Command Software update 89*103*29mm 0.3KG -20~55(workable) 9-12V/1A or 5V/2A 5W 3. System Setting 3.1 Reset there is a RST hole on the front panel which is used to conduct initialization reset for the high-definition encoder. When the equipment is powered on, press the button and hold for 12 Seconds, when the power light is off, release the button, and all the parameters will be initialized. The initialized IP is 192.168.1.168. 3.2 Computer IP Address Setting Computer IP can be set as 192.168.1.*. Note: anyone from 1254, except for 168 3.3 Open IE Explorer Fill http://192.168.1.168 to address bar, Default user name: admin Pass: admin 3.4 Status Display 3.4.1 status: when there is video input, it will display resolution of the input, and if there is not status info,input is not correct, please check your video source or video cable. 3.4.2 main stream : it shows main Stream Encoding Type,Resolution,Bitrate and access address 3.4.3 Sub stream: it shows Sub-Stream Encode Type ,Resolution Bitrate and access address 3.3.4 Preview: a.Click Preview ,it will play stream in browser b.open VLC software to play stream default http stream address:http://192.168.1.168/0.ts default rtsp stream address:rtsp://192.168.1.168/0 4. Network Setting 4.1 Ethernet Port Instructions: in terms of IP address of the equipment, the factory default is 192.168.1.168. If you forget the IP address after modification, you can reset the equipment by pressing the rest button for 12 seconds when the equipment is powered on, and restore the factory default ip. 4.2 WIFI/AP SETTING 4.2.1 AP Mode APAccess Pointmode is default wireless status. Default AP name is AP_Encoder_XXXX,you can sercah hotspot on smartphone or laptop.Default pass is 12345678. Wifi band supports 2.4G/5.8G Wifi channel: if wireless transmit is jam,you can try to swtich channel You also can check ap information on status page. 4.2.2 WIFI Mode Select WIFI mode,you can click Refresh to scan hotspot after reboot Fill correct hotspot name and pass and wifi ip.Click Apply botton,reboot You will check the connection information on status page. If the wifi level is under 60%,please check environment,it is better to visual range away from router. 5. Main Stream Encoding Setting 5.1Encoding Setting of Main Stream 5.1.1 Encoding Type: H.264 or H.265 or Mjpeg 5.1.2 Encode level: baseline profile / main profile / high profile 5.1.3 Encoding frame rate: 5-60 framesit can output 60p When Input is 60p) 5.1.4 Bitrate control: VBR(quality priority) and CBR(bandwidth Priority) 5.1.5 GOP: 30 5.1.6 Encoding size: 1920x1080, 1680x1050,1280x720, 1024x576,850x480,720x576, 720x540,720x480,720x404,704x576,640x480,640x360,608x488, 544x480,480x480,480x384,480x360,480x320,480x272,480x720,400x320 ,400x224,352x480,352x228,320x256,320x240,320x180,240x180,176x 144 5.1.7 Video bit rate: 16-32000K 5.2 Main Stream Protocal Setting UTP protocol(Private) ,Default address http://192.168.1.168/0.utp HTTP protocol,Default address http://192.168.1.168/0.ts HLS protocol,Default address http://192.168.1.168/0.m3u8 FLV protocol,Default address http://192.168.1.168/0.flv RTSP protocol,Default address rtsp://192.168.1.168/0 RTMP pull stream address: Default address rtmp://192.168.1.168/live/0 default port :1935 RTMP push stream address: rtmp://ip:port/xxx/xxx or rtmp://user:pass@ip:port/xxx/xxx RTMP default port: 1935 Multicast protocol,Default address UDP://@238.0.0.1:1234 Unicast protocol,Default address: UDP://@192.168.1.50:1234 (Note:192.168.1.50 is received device) 5.3 OSD Setting 5.3.1 Zone 1-4,you can enable max to 4 image or txt Text, support English/number Character Image, support 24bit BMP file ,less than 500KB,transparency color is R:241 G:241 B:241 5.3.2 X coordinate: the left and right positions displayed by 0-1920 text. Y coordinate: the up and down positions displayed by 0-1080 text. 5.3.3 font: the size of 8-72 text display in the display screen. 5.3.4 Alpha: 0-128 , transparency 5.3.5 Logo: select logo files 5.4 Sub Stream Encoding Setting Note: the setting method is as same as that of main stream 6. Instructions for Youtube Streaming 1.Open live streaming page on Youtube 2.Create a live stream channel 3.Copy rtmp address from Youtube The whole address(part 1+part 2) is rtmp://a.rtmp.youtube.com/live2/87gg-dtd0-7atc-8zwu 4.Paste whole rtmp address into encoder Paste whole rtmp address Enable it Click Apply botton 7. Instructions for Facebook Streaming 1.Open live streaming page on Youtube 2. Copy rtmp address from Facebook The whole address(part 1+part 2) is rtmps://live-api-s.facebook.com:443/rtmp/143998560119176?s_bi=1&.......DIGXA Paste whole rtmp address Enable it Click Apply botton 8. Audio Encoding Settings Audio Bit rate: 48K, 64K, 96K, 128K, 160K, 192K and 256K Audio type: AAC,AAC+,MP3, MP2,AC3,G711A,G711U Audio resample: 44100,48000 9. System Settings 9.1 User name and password change 9.2 Software upgrade 9.3 System settingsDevice reset and initialization default settings This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm etween the radiator & your body.