LED Lighted Medicine Cabinet

Product Models

This instruction sheet contains information on how to install cabinets. This series comes in various sizes. Refer to specific model numbers for dimensions. The cabinets can be surface mounted or recess mounted.

Model Numbers: DSMC2430-3L, DSMC2430-3R, DSMC3630-3, DSMC4830-3, DSMC6030-3, DSMC2430-6L, DSMC2430-6R, DSMC3630-6, DSMC4830-6, DSMC6030-6.

Save these instructions for future use and reference. An improper installation voids the warranty. Installed cabinets cannot be returned. Please feel free to contact the manufacturer for assistance.

Limited Warranty: One Year Term.

Safety Instructions

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical furnishing, basic precautions should always be followed, including the following:

DANGER: Read all instructions before using this cabinet.

WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons:

• Use this furnishing only for its intended use as described in these instructions.
• Do not use attachments not recommended by the manufacturer.
• Never drop or insert any object into any opening.
• Do not use outdoors.

WARNING: Risk of electric shock. Connect this furnishing to a properly grounded circuit only. See Grounding instructions.

CAUTION: Maximum shelf load 100lbs/45.4kg

GROUNDING INSTRUCTIONS

This product must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the product.

CAUTION: An electrical option cabinet must be wired to a 20Amp GFI (Ground Fault Interrupter) circuit breaker when used in bathrooms and all other locations required by the National Electric Code.

SAVE THESE INSTRUCTIONS

Use Tips: Please use in safe voltage range (100V-120V).

WARNING: The installation must be performed by a qualified licensed electrician.

Note: Turn breaker off the electrical supply at the main circuit board before installation and maintenance. ⚡

Model Numbers Explained

Use the chart below to learn how to build a DS Cabinet Model number. This chart references the model number for a 36" W x 30" H x 4" D DS cabinet. Consult the DS Price Book for a complete list of model numbers. The model number is located on the back of your cabinet.

Tools Required

• Drill
• Pencil ✏️
• Level ?
• Measuring Tape ?
• Gloves ?
• Safety Goggles ?
• Phillips Screw Driver ?
• Drill Bit (8mm / 5/16") ?️
• Hammer ?

Parts Supplied

• Z-Mounting Bar (x1)
• Support Bracket (x1)
• Hinge Covers (quantity varies by model)
• Spare Support (quantity varies by model)
• Wire Caps (x3)
• Side Panels (x2)
• Side Panel Covers (x4)
• Side Panel Cover Screws (x10)
• Anchors (quantity varies by model)
• Anchor Screws (quantity varies by model)
• Shelves (quantity varies by model)

Installation Instructions

The medicine cabinet supports two installation methods: 1. Surface Installation and 2. Embedded Installation. Please choose the installation way as needed.

1. Surface Installation

Step 1: Determine placement. The distance between the bottom of the bracket to the top of the mirror should be 2-1/3" (60mm). The recommended installation safety distance from a faucet is 3 inches (at least).

Diagram Description: Illustration showing recommended installation distances: 2-1/3 inches (60mm) from bracket bottom to mirror top, and at least 3 inches from faucet.

Step 1.1: Drill holes. Use a 5/16" drill bit to drill holes at the marked points to a depth of 1-3/4" (45mm). Apply wall anchors with a hammer. Mount the lower bracket to the wall with screws.

Diagram Description: Illustration of drilling holes with an 8mm drill bit to a depth of 1-3/4 inches (45mm), followed by inserting wall anchors and mounting the lower bracket with screws.

Step 1.2: Mount the cabinet. Lift the medicine cabinet and place it securely in the upper bracket. Holding the cabinet in an upright position, secure the lower bracket in the grooves on the bottom of the cabinet.

Diagram Description: Illustration of mounting the cabinet onto the bracket, ensuring it is seated securely.

Note: Gently shake the mirror to ensure that the mirror is securely installed. ✔️

Step 1.3: Install side panels. Attach the side panels to the cabinet.

Diagram Description: Illustration showing the attachment of side panels to the cabinet.

Note: No need to install side panels if the cabinet is recessed. ❌

Step (Board Alignment): Align the slots inside of the board and cabinet. Press down the board until they are clamped together.

Diagram Description: Illustrations showing board alignment and clamping mechanism.

Wire Connection

Connect the wires:

• BLACK WIRE ---- POWER SUPPLY L(LINE)
• WHITE WIRE ---- POWER SUPPLY N(NEUTRAL)
• GREEN WIRE ---- POWER SUPPLY G(GROUND)

Diagram Description: Illustration of wire connection points: BLACK (LINE), WHITE (NEUTRAL), GREEN (GROUND). Includes field wires, grounding screw, and wire connector caps.

2. Embedded Installation Instruction

The wall space must be prepared in advance based on the size of the recessed LED medicine cabinet.

Before installing, it is necessary to determine the opening size, which can be referred to in the table below.

Diagram Description: Diagram illustrating the wall opening dimensions (W: Width, H: Height, D: Depth) required for embedded installation.

Step 2.1: Connect the wires. (Same as Surface Installation wire connection instructions).

Step 2.2: Install the recessed LED medicine cabinet into the prepared wall opening.

Diagram Description: Illustration of the cabinet being placed into the wall opening.

Step 2.3: Insert the tempered glass shelves into the cabinet.

Diagram Description: Illustration of shelves being placed inside the cabinet.

Cabinet Door Installation

Step 3.1: Insert the hinges to the base, then connect the doors with the cabinet.

Diagram Description: Illustration of hinge attachment and door connection.

Step 3.2: Adjust hinges. If necessary, adjust corresponding screws on the hinge to align the doors, ensuring that gaps are even and the doors open and close smoothly.

Diagram Description: Illustration of hinge adjustment for door alignment.

HYDRAULIC HINGE ADJUSTMENT METHOD

Open the "DTC" cover in the direction of the arrow.

Adjustment ①: Adjust the door counterclockwise to move to the right, turn clockwise to adjust the door to move to the left.

Adjustment ②: Twist counterclockwise to loosen it. You can adjust the front and rear direction of the door. Tighten clockwise after adjustment.

Diagram Description: Illustrations showing DTC cover opening and adjustment steps for door positioning (left/right, front/rear).

Note: Since this product has multiple DTC hinges in the cabinet, if you need to adjust the relative position of the cabinet door up and down, left and right, please adjust the hinges for better use of this product.

Buttons Function Explanation

Time/Temperature Screen: ⏰/?️ Displays current time and temperature.

Color temperature touch: ? Tap to cycle through preset color temperatures (White 6000K, Natural 4000K, Yellow 3000K). Press and hold to adjust color temperature steplessly (6000K to 3000K). The cabinet remembers the last selected color temperature.

Light touch: ☀️ Press and hold to adjust brightness steplessly (100% to 20%). The cabinet remembers the last selected brightness. Hardwire installation (wall switches) also works.

Anti-fog touch: ?️ Activates the anti-fog film. Note: The anti-fog film will automatically turn off after one hour. Remember to turn off the switch to prevent energy waste when not in use.

Time function (Left/Right button): In standby state, when the lights are not turned on (off), long press the color temperature button for 5 seconds to activate clock adjustment. The hour can be adjusted first, followed by the minutes after 5 seconds.

Note: The color temperature key is '.', and the light Brightness key is '+'.

Induction LED Strip: The top light bar will automatically turn on and off as the door opens and closes.

Electrical Specifications

Diagram Description: Illustration showing electrical outlets and USB ports.

• Sockets: 120Vac, 2A(Max), 240W
• USB: 5Vac, 3.6A(Max), 18W

Note: Not suitable for high power appliances.