User Manual for Everything Electrical models including: NIDO Steel Ultra Slim Panel Heater, NIDO Steel, Ultra Slim Panel Heater, Panel Heater, Heater
File Info : application/pdf, 12 Pages, 1.85MB
DocumentDocumentNiDO Steel Ultra-Slim Panel Heater User Manual Please read and save these instructions Everything Electrical® BEFORE FIRST USE Read and follow all the instructions in this manual even if you feel you are familiar with the product, and find a place to keep it handy for future reference. For your convenience, record the complete model number (located on the product identification plate) and the date you received the product, together with your purchase receipt and attach to the warranty and service information. Retain in the event that warranty service is required. NOTE: The rating of this product (as marked on the product identification plate) is based on specific loading tests. Normal use or the use of other recommended attachments may draw significantly less power. IMPORTANT SAFEGUARDS When using any electrically powered product, basic safety precautions should always be followed, including the following: PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE USING THE PRODUCT. ! WARNING - to reduce the risk of fire, electrical shock or injury to persons or property: · Read all instructions before using this appliance and keep them for future reference. · Use only the voltage specified on the rating plate of the heater. · Do not cover or restrict airflow to the inlet or exhaust grilles in any manner as the appliance may overheat and become a fire risk. · Do not cover grilles, block entry or exhaust of airflow by placing appliance against any surface. Keep all objects at least 1 meter from the front, side and rear of the appliance. · Do not place the appliance close to a radiant heat source. · Do not operate in areas where gasoline, paint or other flammable liquids are used or stored. · This appliance heats up when in use. To avoid burns, do not let bare skin touch hot surface. Switch off and allow to cool before moving. · Do not use the appliance to dry clothes. · Do not insert or allow foreign object or metal utensils to enter any ventilation or exhaust opening, as this may cause an electric shock, fire or damage to the appliance. · Do not immerse in liquid or allow running into the interior of the appliance, as this could create an electrical shock hazard. · Do not reach for an appliance that has fallen into water. Switch off at supply and · unplug immediately. · Do not operate any appliance with a damaged cord, plug or after the appliance malfunctions or has been dropped or damaged in any manner. Return to a qualified electrical person for examination, electrical or mechanical adjustment, service or repair. · Do not operate appliance with wet hands. · The most common cause of overheating is deposits of dust or fluff in the appliance. Ensure these deposits are removed regularly by unplugging the appliance and vacuum cleaning air vents and grilles. · Do not use this appliance in a window as rain may cause electric shock. · Do not use abrasive cleaning products on this appliance. Clean with a damp cloth (not wet) rinsed in hot soapy water only. Always remove plug from the mains supply before cleaning. · Do not connect the appliance to the mains voltage until completely assembled and adjusted. 2 · This appliance is not intended for use in outdoor locations. · Do not use this appliance in the immediate surrounds of a bath, a shower or a swimming pool or other liquids. · Always operate upright. · Switch off and allow cooling before moving. · Do not operate with cord coiled up as a build up of heat is likely, which could become a hazard. · The use of an extension cord with this appliance is not recommended. · Do not remove plug from power socket until the appliance has been switched off. · Do not remove plug from power socket by pulling the supply cord-always grip plug. · Always unplug appliance when not in use. CAUTION: This product is NOT suitable to be used on long pile carpets or Flokati rugs. · Do not allow cord to come into contact with heated surface during operation. · Do not run cord under carpeting, rugs or runners etc. Arrange cord away from traffic areas so that it will not be tripped over. · Do not twist, kink or wrap the cord around the appliance, as this may cause the insulation to weaken and split. Always ensure that all cord has been removed from any cord storage area. · Do not use outdoors or whilst standing on a damp floor. · Do not store appliance while it is still hot. · This appliance is not intended for use by young children or infirm persons without supervision. · Young children should be supervised to ensure they do not play with the appliance. · The appliance must not be located immediately below a socket-outlet. · Do not use this appliance with another programmer, timer or any other device that switches the heater on automatically, since a fire risk exists if the appliance is covered or positioned incorrectly. · All covers of this appliance are intended to prevent direct access to the heating elements and must be in place when the appliance is in use. ! WARNING: In order to avoid overloading, do not cover the heater. · To reduce the risk of electric shock, do not immerse or expose the product or flexible cord to rain, moisture or any liquid. · The fireguard does not give full protection for young children and for infirm persons. · If the supply cord is damaged, it must be replaced by a qualified electrical persons in order to avoid a hazard. · Do not use this appliance outdoors or on wet surfaces Avoid spilling liquid on the appliance. CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be supplied through an external switching device, such a timer, or connected to a circuit that is regularly on and off by the utility. · Use this appliance only as described in this manual. Any other use is not recommended by · the manufacturer and may cause fire, electric shock or injury. · This appliance is intended for household use only and not for commercial or industrial use. 3 PROPDRUCOTDOUVCETRVOIEVWERVIEW PRODUCT OVERVIEW PRODUCT OVERVIEW 1. Control Pane1l.Control P4an. eWl all mounted bracket4.Wall mounted bracket 2. Power cord2.Power co5rd. Temperature Sensor 5.Temperature Sensor 3. Air Outlet 3.Air Outlet 1.Control Panel 4.Wall mounted bracket SPECSIFPICEACT32IIF..OAPICNior wSAO:eTurtIlcOeot Nrd21..CPoonwtreorl cPoardnel 5.Temperature4.SWenasllormounted bracket 5.Temperature Sensor ModMeol dNeulmNbumerber 3.Air Outlet NDO1-10WETENiNSD10O1-15WT NDO1-E2E0NWiTS15 NDO1-24WT EENiS20 MRRRSaaaoPtttdeeeEeRRDdddlaaiCmPNttPVeeIoueoFoddwmnwlItsePVCabeiroooMegArSlnwrteToasPedgIrOEee(mlCNNmINuF)mD1ICO0b01eA60-r0W1T1000I*W0O500TWN*4N03DN10OD101O50-08110W 3-0W115W55*W052T002TW0*4-20N43D0NVOD~21O02-9510120505-0/25WW260*-005T2W0H040zT*1W04500VN30~DNWO5D201O4-1/0211600-4W202W544H*0TW5z00TW*4N03DO1-242W00T0W RDCDaiIimmRteCeednCUnsVIsiRTooiolntCDnassgIUARRDe((ImGmaaiTmmttRmeeDeAdd)n)IMsAPViooo:G6lnw0taRs0eg*rA5e(m0M*m40)3606008103x0*5055*00522W*024x0*04-243043003V~839515055*/50526*00205W0H*04-z*208443300P35VC~Bx 522x0040W03 501/6104H5*z50*403 955*50*403 249005W5 x 52 x 403 1145*50*403 CIRCUIT DIAGRAM CIRCUIT DIAGRAM PCB PCB PCB Heating Element PCB Temperature Sensor PCB Thermostat Heating Element Temperature Sensor Heating Element Temperature Sensor Thermostat Thermostat MOUNTING GUIDE MODEL NDO1-10WT 1000W 600 250 MMoONdDDeOEl1L-15WPMTo(W OwD1e)5Er00LW 8L35 mm 25 0L1 mm NNEDDEOON1N1Ni--SDD11105OO0WW11T--T2204WNW111D0TT50O0001000-WW221W04000W00TWW86305016109010504220555W500 250 252605000 250 EENiS15 NDO1-20WT N1D250O00100-W1W5WT95518530502W50 285305 250 NEDEON1iS-2240WT N2D204O00100-W2W0WT114529050502W50 295505 250 NDO1-24WT 2400W 1145 250 4 WALL MOUNTED MODE TAKE DOWN THE HEATER FROM WALL 10mm 10mm Wall mounted mode Wall mounted mode CEILING/PICCTeiUlinRgE/PFicRtAurMe fErame Ceiling/Picture frame Air outlet Air outlet Minimum 1000mm Minimum 1000mm Minimum M10in0immmum 100mm Minimum M10in0immmum 100mm Floor Floor Minimum 100mm Minimum 100mm Pull up the heater 10mm PuPthlluetlnlhuetpahkteehaedteohrweuanptethr10e1m0hmemamtaenrd awthaeny ftarokme dtohwe nwtahlel, thheeantetrake down the heater. Take down the heater from wall Take down the heater from wall This heater MUST be installed tdtdtToohiihssettittshhaaheennhecceammeeateiisstnner.aaiirmmttMttuuhhUmmeeSffTrrooeeuubqqrreuussiirrineeiiddsddeetasslleoodff the heater. CACCSTOOOCNNaRTTs: RRItNeOOrS12LLTInAPPsLAAtL1aA1NNlTlaEEI1Ot0LLio9Nn&&RrEeMmOo8VvAaLl 12 11 10 9 SSccrreew8w 7 7 3 1 3 12 11SS1creeww 1132 11 13 13 13 14 2 14 2 1 2 34 5 6 1.Powe1r But2ton 3 1 4 85.Tempe6rature Indicator IIRnNEsS123456234567MeT............rPMHEDTMHEDTHAOt1iioCCLeieiecmmooV.ggLwIaaaoudOdOAiineettAtttmeeepaaiiiLrrsTnnnMMrllw:pSSeIIgggIDDnnBOoooareeddPPIiiutddnrssttnNiittttdeeoocceppiidth:nnoaawwsnlliIIaaeggcnttnn,teeooyyaddac"rrrrtiioolcc21irgaam"ttnooipnrrtothoneehsnoclte118991111111r"e00...4332211"TSS..w.......1e2llWWCUUTTTTeemhee"iiee"hppmm,IImmopFFppiiwwplneeeldIIppueaaMMtrrrseeoaMMLrr,BBoohddrrtoaaatoouddssuuchunttddr//eettkuuDDpettedeeoorrwIIooBeeInnnnhtIInwwhnnuddaoSSdddteiinnrlcctieedeciiowwnccaattsanttaattaa"tiitoonntttiorrooogrrdd2ggrrrhssaBBt"AAleiuugiddnnttnttjjoouuttthnnhsshtteemmecseesoccnnrrrtteerBBewwuuc.tthttoodonnilere, acntidonti,gphutesnhtihte screw. Tak7e.Ho2eu.aTttatinhkgeeIsoncdurietcwtahtoearnsdcrreewmowvie1th4t.haCethociaoldsl,tLtohorce. knBreumttoonve the caster. 5 Select 2.4 GHz Wi - Fi Network and enter password . e If your Wi - Fi is 5GHz, please set it to be 2.4GHz. Common router setting method 100mm CONTROL PANEL Wi-Fi - 5Ghz Wi-Fi - 2.4Ghz 100mm Floor CONTMRinOimLumPA10N0EmLm This heater MUST be installed to the minimum required distances at the four sides of the heater. 3 *** 1. Power Button 2. ******** Mode Setting 12 11 10 9 8 Floor 12 3. Next Heating Power 13 4. ECO Mode Indicator 5. Digital DisplCayONTROL PANEL 7 3 141 6. Timer Indicator 7. Heating Indicator 12 8. Temperature Indicator 11 10 9 1 8 2 34 9. 10. 11. Sleep Mode Indicator 1.Power Button WIFI Mode Indicator Temperature Setting Button 2.Mode Setting 7 3.Heating Power 4.ECO Mode Indicator 12. Timer Button 5.Digital Display 12 11 5 6 13 8.Temperature Indicator 13 190.S.lWeeIFpIMMooddee1In4Inddicicaatotor r 2 11.Temperature Setting Button 12.Timer Button 13. Upwards/Downw1ards2Adju3st6m.T4eimnterBIun5tdtiocanto6r 13.Upwards/Downwards Adjustment Button 14. Child Lock B1u.Ptotowner Button 7.Heating8.ITnedmicpaetorar ture Indic1a4to.rChild Lock Button 2.Mode Setting 9.Sleep Mode Indicator 3.Heating Power 10.WIFI Mode Indicator 4.ECO Mode Indicator 11.Temperature Setting Button OPERATION 5.Digital Display 12.Timer Button 6.Timer Indicator 13.Upwards/Downwards Adjustment Button TO BEGIN: 7.Heating Indicator 14.Child Lock Button 1. Take out the heater from the carton carefully, and save the carton for off-season storage. 2. Ensure the heater is fully assembled according to the Mounting Guide. 3. It's recommended not to use the same electric outlet as other high wattage electrical appliances in order to avoid overloading your circuit. TURN ON: · Plug in the heater. The power indicator lights up and the heater is in stand-by mode indicated by a short beep. Press power button 1 to turn on the heater with buttons 1/2/3/11/12 on. Then the product starts working. TEMPERATURE SETTING: · The default temperature is factory-set to 35°C. · Press button 11, temperature indicator flashes and its setting is activated. Press button 11 again to select desired temperature (5°C to 45°C). Or Press 11 on the remote and then press upwards/downwards adjustment button for required temperature. (Setting temperature should be higher than room temperature). · Leave it for 5s, heater saves the settings automatically and starts heating with Button 7 lights on, while display screen switches to show between heating power and current room temperature. In working mode, indicator 7 lights on when high heating and off when not heating. HIGH/LOW HEATING SETTING: In working mode, press button 3 to select low heating power and high heating power. P1 shows when working at low heating power, while P2 shows when working at high heating power. 6 TIMER SETTING: · Press button 12 , setting time is displayed while timer indicator flashes. Press button 12 again to select working hours (0 hour-24 hours), or press 12 on the remote and then press up/down adjustment button to set required timer. · Leave it for 5s, heater saves the settings automatically and starts to time, while the display switches to show between heating power, current room temperature and timer. Indicator 6 lights on when display switches to show timer. CHILD-LOCK SETTING: · In working mode, Press button 2 or 14 on the remote for 5s, system is locked with "[ ]" displaying. No setting can be changed at this time. After 3s, display screen resumes to show heating power, current room temperature and timer switching. · Methods to unlock: Press button 2 or button 14 on the remote for 5s, the unit is unlocked. WORKING MODE SETTINGS: · In working mode, press power button 2 to select Sleep mode, ECO mode or Normal Mode. SLEEP MODE: · The display goes to sleep mode and it only shows sleep model indicator 9 and heating indicator 7. Press button 2 once again, all the buttons resume to show in the display. · If no button is pressed for 10 seconds, the display goes to sleep mode again. ECO MODE · In working mode, press button 2 to select ECO mode with indicator 4 on. · In ECO mode, system sets the temperature to 23°C. Heater runs in high heating power P2 at lower than 21°C, whilst it runs in low heating power P1 at higher than 21°C. NORMAL MODE: · Press button 2 to select normal mode with both indicator 9 and indicator 4 off. SWITCHING THE DISPLAY BETWEEN DEGREES FAHRENHEIT AND CELSIUS: · Press the button 11 and 2 for 5s. OPEN WINDOW DETECTION · The open window detection is `closed' by default. Press and hold the power button 1 and 12 for 5 sec, "OP" shows on the display, the open window detection is now `opened' · If you want to close the open window detection, press and hold the power button 1 and 12 again for 5 sec, "CL" shows on the display, the open window detection is now closed. WIFI MODEL ONLY RESET: · Press button 3 ( ) for 5s, WiFi setting is reset with its indicatior blinking rapidly (twice per second). WiFi is now initiated. TIP OVER SWITCH: · Auto turn off function: the product is equipped with tip-over switch, if the heater falls over, please put the product in a flat position and restart. TURN OFF: · Press button 1 - heater stops working. Turn off power supply - unit power is off. SAFETY FEATURE: · The unit is equipped with a high limit switch, the heater will automatically shut off if it is in an over-heating condition. · The heater will automatically turn back on when it has cooled down. 7 TROUBLESHOOTING If your heater fails to operate and alarm, please follow these instructions: Display E1 E3 E4 E5 Problem Temperature sensor is abnormally disconnected High temperature alarm Open window detection Heater is tipping Troubleshooting Send it to service center for reparation directly. Keep heater away from other heat sources. Close the windows, restart the heater. Keep heater stood well. SMART LIFE APP SET UP* *WiFi Model Only: 1 Download Smart Life App SSccaann tthhee QQRR ccooddeebbeelolowwfofroar saimspimlepdleowdnolwoandlouasdingusyionugr ysomuarrst mdeavrict ed.evice. AAlternaattiviveelyly, ,sseeaarcrchh'S`SmmaartrLt iLfeif'eo' noynoyuor udredviecveicaeppalipcaptliocnatsiotonrestordeotwondlooawd.nload. Register Log In With Existing Account CONNECCoTnnHeEcAtTHEeRa: ter 1. 2. 1. Enter the interface. En2te. rCtlhicek itnhteer+faiccoen. in the upper right-hand corner or alternatively Cl3ic.kGtoheto+SicmoanllinHtohmeeuApppeprliaringchets-haannddsceolerncet rHoeraateltr.ernatively QUICK & EASY presWs IAFdI dSEDTeUvPicVe.IDEO: pr4e.ssEAntdedr tDheevcicoerr. esponding password to the chosen Wi-Fi network account. 3. Go5.toChSemcakllthHaotmtheeAWpip-Fliiainccoensisanbdlinskeinlegcot nHethaetedre. vice and tick the 'Confirm indicator 4. Enterratphiedlcyobrrlienskpinogn'dbinogx.pIfatshsewinodrdicoaftotrhies cnhoot sbelinnkWinig-FrienseettwthoerkWi-Fi (see Operation accoIunnsttr. uctions). 5. Pre6s. sSbeut tthtoend3ev( ice) ifnofro5rms,aWtioiFni asentdtipnrgeisssreDsoentewtoithenittseirntdhiecactoionrtrol interface where bliynokuinwgilrlanpoidwlybe(twabiclee tpoecrosnetcroolntdh)e. WheiaFtieisr.now initiated. 6. Set the device information and press Done to enter the control interface where you will now be able to control the heater. Add Device Electrical Lighting Two Seasons 8 Heater Heater Heater Select 2.4 GHz Wi - Fi Network and enter password . If your Wi - Fi is 5GHz, please set it to be 2.4GHz. Common router setting method Select 2.4 GHz Wi - Fi Network and enter password . If your Wi - Fi is 5GHz, please set it to be 2.4GHz. Common router setting method 1. Enter the interface. 2. Click the + icon in the upper right-hand corner or alternatively press Add Device. 3. Go to Small Home Appliances and select Heater. SMART4.LEIFnEteAr PthPeScEoTrrUesPp*onding password to the chosen Wi-Fi network account. 5. Check that the Wi-Fi icon is blinking on the device and tick the 'Confirm indicator *WiFi MordaeplidOlynlbyl:inking' box. If the indicator is not blinking reset the Wi-Fi (see Operation Instructions). 2 6. Set the device information and press Done to enter the control interface where you will now be able to control the heater. No devices Add Device Home Scene Smart Me Add Device Electrical Two Seasons Lighting Sensors Heater (Wi-Fi) Heater (BLE) Heater (Zigbee) Large Home Appliances Small Home Appliances Heater (other) Oil Heater (Wi-Fi) Electric Blanket (BLE+Wi-Fi) Kitchen Appliances Exercise& Health Electric Blanket (Wi--Fi) Electric Blanket (BLE) Electric Fireplace (BLE+Wi-Fi) Camera & Lock Gateway Control Electric Fireplace (Wi-Fi) Baseboard Heater (BLE+Wi-Fi) Warming Table (BLE+Wi-Fi) Outdoor Travel Warming Table (Wi-Fi) Fan (BLE+Wi-Fi) Fan (Wi- -Fi) Select 2.4 GHz Wi - Fi Network and enter password . If your Wi - Fi is 5GHz, please set it to be 2.4GHz. Common router setting method You are connected to a 5 GHz Wi - Fi network . Switch to one of the following 2.4 GHz Wi - Fi networks and continue . Switch Continue with Current Network Next Select 2.4 GHz Wi - Fi Network and enter password . If your Wi - Fi is 5GHz, please set it to be 2.4GHz. Common router setting method Wi-Fi - 5Ghz Wi-Fi - 2.4Ghz *** ******** Next 3 Reset the device Reset the device 7 Connecting Device Keep the network stable. Press and hold the RESET button for 5 seconds until the indicator blinks (subject to the user manual). Confirm the indicator is blinking Reset Device Step by Step Press and hold the RESET button for 5 seconds until the indicator blinks (subject to the user manual). Select the status of the indicator light or hear the beep : Blink Slowly Blink Quickly Scan devices . Register on Cloud . Initialize the device . Add Device 1 device (s) added successfully Heater Added successfully 0 device(s)being added Done Heat Heating Level High Set temp. C/F Heating Current Temperature 30°C Heating Area temp. C Decrease temp. In9crease temp. F Done 4 Heat Heating Level High Set temp. Heating Decrease temp. Mode High Low Neutral Done Settings Timer Mode ON/OFF Current Temperature 30°C Heating Set Temp Switch Mode Ti mer Settings Area temp. Increase temp. Settings ECO Lock Temp unit convert °C Schedule Ti mer Cancel 1Hour 2Hours 3Hours 4Hours Done C/F C F Done Window opening detection Button child-lock °C/°F Button Schedule Schedule Save Repeat Note Notification Power Once ON CLEANING INSTRUCTIONS Cleaning behind the heater It is very easy to clean behind it. Holding both sides of the heater, lift upwards and then pull forwards. The heater requires regular cleaning,8to ensure trouble-free operation: · Isolate the power supply to the heater before cleaning. · Ensure that the heater has been allowed to cool down completely before cleaning. · Use a damp cloth (not wet) to wipe the exterior of the heater to remove dust and dirt. · Use a vacuum cleaner to remove dust and fluff from around the grilles. (Failure to do this may cause discoloration) · Ensure the heater is dry before connecting back into the mains supply. SERVICE If you require service, contact your local dealer. REPLACEMENT OF SUPPLY CORD If the supply cord is damaged, it must be replaced by a service agent or equivalent qualified person, in order to prevent a hazard. STORAGE If you do not plan to use the heater for extended periods of time, it is recommended that the heater is cleaned and then stored (preferably in its original packaging) in a cool dry place. 10 ELECTRICAL WASTE RECYCLING Providing solutions to your requirements All our equimpent comply with EU WEEE Directive (2012/19/EU) and bear the classification symbol for waste electrical and electronic equipment (WEEE). The equipment have been manufactured with high quality parts and materials which can be reused and are suitable for recycling. Therefore do not dispose the equipment with normal household waste at the end of its service life, but return to Velair Group for recycling. Velair Group takes its responsibilities under the WEEE Regulations extremely seriously and has taken steps to be compliant in line with our corporate and social responsibilities. In the UK, Velair Group has joined a registered compliance scheme with Valpak. Velair Group Registration number is RM10064 Disposal and Recycling of old equipment. Business Users WEEE RETURNS 1st July 2007 saw the introduction of the WEEE Regulations 2006 and this will have a major impact on the way we deal with end of life electrical and electronic equipment (eee) in the UK. From that date the producer (manufacturer or importer) of the equipment has a duty to treat and recycle products which they have put on the market. This means that our business customers will be able to dispose of equipment in an environmentally friendly way. The rules concerning what can and cannot be collected are complex and that is why we have decided to make things as simple as possible for our customers. Which WEEE is what? 1. If the equipment is marked with a crossed out wheelie bin with a bar underneath then it is the responsibility of the producer who manufactured or the supplier who imported it to recycle the products. It is a legal requirement to display this symbol on all eee placed on the market after the 13 August 2005 2. If there is no wheelie bin there are two possibilities, either it will be the responsibility of the end user, or if you have purchased a direct replacement for the item it will be the responsibility of the manufacturer who is supplying the NEW equipment. 3. All producers/importers of equipment should by now have joined a Compliance Scheme and it is the schemes that will organise to treat and recycle the end of life equipment from the end users. Velair Group are members of the Valpak Compliance Scheme. Please return our end of life equipment to: Velair Group, 2E Queensway, New Milton, BH25 5NN. 11 WARRANTY THREE YEAR WARRANTY. We warrant the model covered in this manual to the original user against any defects in workmanship or materials under normal use for a period of three (3) years from the date of purchase. However, this warranty excludes damages resulting from normal wear and tear, motor burnout, incorrect use, incorrect installation, and any consumable parts. If any part of the product is found to be defective in material or workmanship and returned to an authorised party, we will repair or replace the defective part. Please note that in the first instance, you should contact your retailer or supplier for details on how to claim a warranty repair or replacement. Please be advised that our warranty does not cover damages resulting from misuse, abuse, or any modifications made to the product. Additionally, any repairs or replacements made outside of our authorised service centres will void the warranty. By purchasing and using our product, you acknowledge and accept the terms of this warranty. We reserve the right to determine the validity of any warranty claims and to amend or revoke this warranty at any time without prior notice. PRODUCT SUITABILITY: We understand that various jurisdictions have their own codes and regulations that govern the sales, construction, installation, and/or use of products for specific purposes. While we strive to ensure that our products comply with these codes and regulations, we cannot guarantee compliance nor be held responsible for the installation or use of our products. We strongly advise that you review the product application and all applicable national and local codes and regulations before purchasing and using our products. It is your responsibility to ensure that the product, installation, and use are in compliance with these codes and regulations. By purchasing and using our products, you acknowledge and accept the responsibility for complying with all applicable codes and regulations. Our warranty does not cover any damages or liabilities resulting from non-compliance with these codes and regulations. 12Adobe PDF Library 17.0 Adobe InDesign 18.1 (Macintosh)