Nakamichi Mobile Audio Systems – Nakamichi Car Audio
User Manual for Nakamichi models including: NDSD200 DSD Player with DSP, NDSD200, DSD Player with DSP, Player with DSP, DSD with DSP
– Nakamichi Car Audio
Nakamichi NDSD200 - köp online på dBakuten.se
File Info : application/pdf, 16 Pages, 3.57MB
DocumentDocumentNDSD200 DSD PLAYER WITH DSP 1 EN Thank you for your purchase and welcome to the world of Nakamichi! Please keep your original proof of purchase or invoice in a sate place in case of any warranty claims. Do also mail or register your warranty With the ofcial Nakamichi service centers and/or agents to ensure that you are provided with the relevant technical support if required. 1. To prevent short circuit, please keep the device away from water or damp places. 2. If water or any other liquid enters the device, cut off the power immediately, and inform the nearest Nakamichi Service Center or Agent to inspect the product. 3. Users are not recommended to disassemble the device as there are no user serviceable parts inside, please contact the nearest Nakamichi Service Center if necessary. Ensure all cables and parts are securely connected before turning on the power.Shown below is the basic troubleshooting procedure that you should follow. Before sending the unit for repair, please refer to the table for common troubleshooting solutions. Troubleshooting method: Malfunction No Power No Sound Unable to connect through USB Please return the unit to factory settings Please consult the nearest service center or authorized agent for further aptions Reason and Solution Check the power connection and make sure it's secure. Check the ACC connection and make sure it's secure. Double check if the unit is in MUTE mode. Check if you have choose the correct input channel. Check the USB connection and make sure it's secure. Check if the driver " HID-compliant device " has been properly installed in your PC. NDSD200 User Manual USB2.0 Cable(1.5m) Mechanical at head screws(PM3x6mm) Self-Tapping Oval Head Screws(PA4x20mm) Mounting brackets Velcro(160x20mm) 20P high level input and power cable(18cm) 16p Speaker cable(18cm) 20A FUSE 1Chinese,1English 2 EN Dynamic Range(RCA Input) S/N(RCA Input THD Frequency Response Input Impedance Low Level Output Impedance Signal Input Range Signal Output Range Working Temperature Supported Audio Formats Support hard disk capacity Power REM Intput REM Output Standby Power Net Weight Product Dimension 100dB 55dB 0.5 20Hz~40KHz High Level: 51 51 RCA: 7.5Vpp; High Level: 26Vpp RCA: 7.5Vpp; Max Power: 8CHx50W -20 ~ 70 DSD64/DSD128/DSD256/Mp3/WMA/WAV/APE/FLAC DSD file format: ".dff" , ".dsf" 2T DC 9V~15V High Level Input Signal: H1+/H1- or ACC control cable 12V Start up Voltage Output(250mA) 0.1W Approx.1.2kg 190(L)x153(W)x55(H)mm Input Type Output Type Output Gain Output Signal EQ Output Signal Crossover Output Phase and Time Alignment Presets 3 EN 6 CH High Level, 4 CH Low Level, Built-in Bluetooth, U disk music 10 Channels Low Level, Optical, Max Power: 8CHx50W Gain Range: Mute,-59.9dB~6dB 31 Band Equalizer Engine: 1. Frequency range: 20Hz~20KHz, 1Hz Accuracy 2.Q value (slope): 0.404~28.852 3.Gain: -20.0dB~ +20.0dB, 0.1dB Accuracy Each output is equipped with multi-order high and low pass independent lters. 1. Filtering types: Link-Ril, Butter-W, Bessel 2. Filtering frequency division point: 20HZ~20KHz. Resolution 1Hz 3. Filter slope (slope) setting: 6dB/ Oct to 48dB /Oct and OFF Each output channel can be adjusted for phase and delay, parameter range: Phase: in-phase or reverse-phase (0 /180 ) Delay: 0.000 to 20.000ms. 0 to 692 cm, 0 to 273 inch 6 Presets into the device 153mm 190mm OUTPUT INPUT CH9 CH7 CH5 CH3 CH1 CH3 CH1 CH10 CH8 CH6 CH4 CH2 CH4 CH2 NDSD200 OPT-OUT ACC HOST PC USB REM OUT8 OUT7 OUT6 OUT5 OUT4 OUT3 OUT2 OUT1 OUT8 OUT7 OUT6 OUT5 OUT4 OUT3 OUT2 OUT1 SPK OUT IN6 IN5 IN4 IN3 IN2 IN1 ACC GND GND GND IN6 IN5 IN4 IN3 IN2 IN1 REM OUT B B B HI.LEVEL INPUT POWER 55mm 55mm The Velcro Is Attached To The Bottom Of The Fuselage 4 EN OPT-OUT ACC HOST PC USB REM OUT8 OUT7 OUT6 OUT5 OUT4 OUT3 OUT2 OUT1 OUT8 OUT7 OUT6 OUT5 OUT4 OUT3 OUT2 OUT1 SPK OUT IN6 IN5 IN4 IN3 IN2 IN1 ACC GND GND GND IN6 IN5 IN4 IN3 IN2 IN1 REM OUT B B B HI.LEVEL INPUT POWER 8x50W 4 5 EN 2 4 5 6 78 OPT-OUT ACC HOST PC USB REM OUT8 OUT7 OUT6 OUT5 OUT4 OUT3 OUT2 OUT1 OUT8 OUT7 OUT6 OUT5 OUT4 OUT3 OUT2 OUT1 SPK OUT IN6 IN5 IN4 IN3 IN2 IN1 ACC GND GND GND IN6 IN5 IN4 IN3 IN2 IN1 REM OUT B B B HI.LEVEL INPUT POWER OUTPUT INPUT CH9 CH7 CH5 CH3 CH1 CH3 CH1 CH10 CH8 CH6 CH4 CH2 CH4 CH2 NDSD200 9 10 USB2.0 Port, Connect to the computer tuning software No need to download the driver installation, connected to the computer sound software installed automatically. USB port Insert the USB ash drive and play the song in the USB ash drive under the player audio source. SUPPORTED AUDIO PLAYBACK LIST Audio Stream MP3 32kbps-384kbps WMA 0kbps-320kbps WAV 32kbps-384kbps APE all bitrates allowed FLAC all bitrates allowed DSD64 all bitrates allowed Sampling Rate 8/11.025/12/16/22.05 24/32/44.1/48KHz 8/11.025/12/16/22.05 24/32/44.1/48KHz 8/11.025/12/16/22.5/ 24/32/44.1/48KHz 8/16/22.05/24/32/ 44.1/48KHz 8/16/22.05/24/32/ 44.1/48KHz 2.8224MHz Remark MPEG1/2/2.5 layer II&III WMA standard 4/4/1/7/8/9.1 4bit ADPCM only PCM Bit width 8/12/16/24bits PCM Bit width 8/12/16bits dsf dff DSD128 all bitrates allowed 2.8224MHz dsf dff DSD256 all bitrates allowed 2.8224MHz dsf dff 6 EN SUPPORTED DEVICES Audio USB Micro SD/TF SSD/HDD Maximum capacity 256GB 256GB 2T Device format FAT32/NTFS FAT32/NTFS FAT32/NTFS The controller port Data call and total volume adjustment can be performed by the line controller. HOST ACC AC3-DSD (Optional wiring controller) REM PWR/PRO H1 H2 H3 H4 H1 H2 H3 H4 Optical input port Connect on-board or other audio equipment and switch the sound source of the machine to digital output. High level output port OUT8 OUT7 OUT6 OUT5 OUT4 OUT3 OUT2 OUT1 OUT8 OUT7 OUT6 OUT5 OUT4 OUT3 OUT2 OUT1 SPK OUT High level input and power port 1~6 High level input. IN6 IN5 IN4 IN3 IN2 IN1 ACC GND GND GND IN6 IN5 IN4 IN3 IN2 IN1 REM OUT B B B HI.LEVEL INPUT POWER Machine start mode switch When the switch is turned to the "ACC" terminal, the machine is started by ACC, and when it is turned to the "HOST" terminal, the machine is started by the high level H1+/H1- input signal. Power indicator light/Protection indicator light Low level output port Connect up to 10 channels low level output. Low level input port Connect up to 4 channels low level intput. 7 EN PC Software Operation Introduction (PC can be downloaded from the ofcial website (http://www.nakamichicaraudio.com, CONTACT, downloads)) Computer Conguration Requirements: Screen resolution higher than1280 x 768, otherwise the software Ul is incomplete, only suitable for windows operation system laptop, desktop and pads. 1. Menu editing area Main functions: File, options operation. a. Click the "File" pop-up window, and select to load the scene on you computer, save it as scene on you computer, load the whole machine scene or save the whole machine scene. Note: If you need to share tuning parameters, please connect the machine, and "save machine scene" to the personal computer to share this " machine scene". b. Click on "Option" to select Chinese and English switching, Noise Gate, RESET, InPutVOL and About(A) 8 EN 2. Function editing area Main functions: scene, master source, mixer source, channel type, link, mixer and mode settings. a. Scene: 6 sets of scene data can be recalled or stored. b. Master source: Click the input audio source drop-down list to select the input audio source. BT, Hi Level, Low Level and DSD. c. Reset: Click Reset to clear the channel type or restore the default channel type. d. Link: Click the Link to set the Link synchronization mode: copy from left to right or copy from right to left. e. Click "Mixer" to enter the mixing interface, the interface is as shown below. f. Click "Audio" to switch Sound mode. 3. Main volume and software connection editing area Main functions: master volume and computer software connection settings. a. Main volume adjustment range: off, -59.9~6dB. Click the speaker button to mute the main volume. b. Click the "Not Connected" button to connect the host with a PC. 9 EN 4. Output channel type editing area Main function: congure the type of output channel. 5. Channel delay, volume, phase editing area a. Push the fader left or right to adjust the sound size, or enter a value or roll the mouse wheel in the volume input box to adjust the sound size. Click the speaker button to switch mute. b. Positive phase adjustment: Click0°or180°to switch between positive phase and reverse phase. c. Delay: set the delay value by scrolling the mouse wheel in the delay input box, or enter the value to set the delay value. d. Delay Unit button: Click the drop-down list to select milliseconds, centimeters, and inches. 6. Channel divider editing area Main Function Setup: Channel High & Low Pass Filter Setup. Adjustable: Filter Type, Frequency point and Q Value (Gradient or Slope). 10 EN 7. Equalizer editing area a. Reset EQ: It is used to restore the parameters of the all equalizer to the original pass-through mode (the frequency of the equalizer, the Q value and the gain are restored to the initial value). b. Restore EQ: Switch between the currently designed equalizer state parameters and the pass-through mode (the gain of all equalization points is restored to 0 dB, the frequency and value are unchanged). c. Click PEQ Mode to switch GEQ Mode. The Q value and frequency cannot be adjusted in the PEQ Mode interface. 8. Channel EQ editing area Main function conguration: Equilibrium design of current output channel, 31-band equalization adjustable: frequency, Q value (response bandwidth) and gain (increasing or decreasing the frequency response amplitude near the frequency point). 11 EN Smart-phone Software Operation Instruction (APP can be downloaded from the ofcial website(http://www.nakamichicaraudio.com,CONTACT, Downloads)) Home Delay Output 1. Home interface It can restore factory settings, share sound effects, save sound effects, turn on local sound effects, check the model and version number of the unit, and exit the software operation; volume, master source, storage and recall of 6 sets of preset scenes. A. Connection Status: Red means not connected, green means connected. B. Menu: You can restore factory settings, share sound effects, save sound effects, turn on local sound effects, view the model and version number of the machine, and exit the software operation. C. Master source: Master source: Bluetooth / Hi.level / Low level / DSD. D. Volume adjustment: Press and hold the volume scale clockwise or counterclockwise to adjust the volume. The main volume range is 0~66, The subwoofer range is 0~60. E. Scene preset: There are 1~6 presets to choose from. F. Advanced settings: Click [Advanced Settings] to enter the settings of the delay interface, channel interface, EQ interface and mixing. 2. Delay interface Sound eld positioning output delay adjustment. G. Unit switching: Switch between milliseconds, centimeters, and inches. H. Delay setting: Click setting window of the corresponding channel. Slide the dots left and right to set the delay value. Delay settings can be made for CH1~ CH10 speakers. Delay range: millisecond range: 0.000~ 20.000; cm range: 0~692; inch range: 0~273. 3. Channel interface Channel high-low-pass crossover setting with high-low-pass independent ltering. 12 EN EQ Adjustable: Filter type, frequency and Q value (slope or slope). I. Output channel selection: Ten channels are available. J. Output channel volume setting: You can adjust the volume by sliding left and right. The volume range is 0~60. Click the speaker button to mute. Congurable output channel type, forward and reverse switching. K. Channel divider selection: Channel type: Choose from Link-Rill, Butter-W and Bessel. Frequency Range: 20HZ~20KHz. Slope selection: 6dB/Oct, 12dB/Oct, 18dB/Oct, 24dB/Oct, 30dB/Oct, 36dB/Oct, 42dB/Oct,48dB/Oct and OFF can be selected. L. Joint tuning settings: Click[link] the joint debugging window 13 EN Mixer will pop up, and select the joint debugging method. 4. EQ interface Corresponding to the adjustment of the output channel EQ curve (gain, Q value and frequency); reset equalization, pass-through equalization or parametric equalization operation settings. M. EQ display: Edit the display area. N. Output EQ gain, Q value and frequency settings: Output EQ gain setting: A total of 31 EQ. left and right sliding screen can select EQ, you can drag the slider up and down. Select the rst line value, and drag the slider bar left and right in the pop-up dialog box to adjust the adjustment range: -20dB ~ +20dB. Q value: Click the second line value, and drag the slider bar left and right in the pop-up dialog box to adjust, the adjustment range is 0.404 ~ 28.852. Frequency setting: Click the third line value, and drag the slider bar left and right in the pop-up dialog box to adjust it. The adjustment range is 20Hz ~ 20KHz. O. Reset equalization, restore equalization, pass-through equalization settings: Click [Reset EQ] to restore the parameters of the 31-band equalizer to the original pass-through mode (the equalizer frequency, Q value and gain are restored to their initial values). When there is channel adjustment, display [straight-through equalization], click [straight-through equalization], click [OK], all values (frequency, Q value and gain) will return to the initial value. At this time, the [straight-through equalization] button will become [recovery equalization]. Press the button and click [Resume Equilibrium], all values (frequency, Q value and gain) will be restored to the value before the pass-through. Click [P.EQ Mode], click [OK] to switch to Graphic Equalization, click [G.EQ Mode], click [OK] to switch to Parametric Equalization. 5. Mixing interface Four sound source modes can be selected. It includes the mixing selection and adjustment of 6 groups of high-level, Bluetooth left and right channels, DSD left and right channels, and aux left and right channels. The adjustment range is 0-100. 14 EN