FSP 700W Medical ATX Power Supplies

PB SERIES

Features

Design meets IEC 60601-1 & IEC 62368-1
Meets Intel x86 platform requirement
Meets 80PLUS GOLD efficiency
Meets EN 55011 class B emission
BF class isolation

Safety Standard Approval

Certifications include: C, E211696, R, A, EN 60601-1, IEC 60601-1, US, TÜV Rheinland CERTIFIED, CE. More information available at www.tuv.com (ID 6008000000).

Description

This series of AC/DC switching power supplies is housed in a standard ATX form factor (165 x 150 x 86 mm) and delivers 600 or 700 watts of continuous power. The PSU incorporates a built-in DC/DC converter for +3.3V and +5V output rails to enhance load regulation. The high-efficiency design complies with 80PLUS GOLD standards.

Input Specifications

Input voltage: 90-264 VAC

Input frequency: 47-63 Hz

Input current:

FSP600M-70PB: 7 A (rms) @115Vac, 60Hz / 3.5 A (rms) @ 230Vac, 50Hz
FSP700M-70PB: 8 A (rms) @115Vac, 60Hz / 4 A (rms) @ 230Vac, 50Hz

Earth leakage current: 300 μA max. @ 264 VAC, 63 Hz

Output Specifications

Output voltage/current: See rating chart.

Max. output power: See rating chart.

Ripple and noise: See rating chart.

Protection

Overvoltage: +3.3V, +5V & +12V, Latch off
Overcurrent: +3.3V, +5V & +12V, Latch off
Overtemperature: +3.3V, +5V & +12V, Latch off
+5Vsb, -12V, -5V: Auto-recovery

Output Voltage/Current Rating Chart

Outputs	FSP600M-70PB		FSP700M-70PB		Load Regulation	Ripple & Noise ²
	Mini. Load	Maxi. Load	Mini. Load	Maxi. Load
+3.3 V	0 A	24 A	0 A	24 A	±5%	50 mV P-P
+5 V	0 A	30 A	0 A	30 A	±5%	50 mV P-P
+12 V1	0.1 A	peak 30 A	0.1 A	peak 35 A	±5%	120 mV P-P
+12 V2	0.2 A	peak 30 A	0.2 A	peak 35 A	±5%	120 mV P-P
- 5 V ¹	0 A	0.2 A	0 A	0.2 A	±10%	100 mV P-P
-12 V	0 A	0.5 A	0 A	0.5 A	±10%	120 mV P-P
+5 Vsb	0.05 A	3.0 A	0.05 A	3.0 A	±5%	50 mV P-P
+3.3 V & +5 V Combine Output Power	150W Maxi.		150W Maxi.
+12V Total Output Power Maxi. / Peak ³	50A Maxi. / 660W peak		58A Maxi. / 780W peak
Total Output Power	600W		700W

Notes:

-5V is not for standard model but upon request.
Ripple and noise measurements shall be made under all specified load conditions through a single pole low pass filter with 20MHz cutoff frequency. Outputs shall be bypassed at the connector with a 0.1uF ceramic disk capacitor and a 10uF electrolytic capacitor to simulate system loading.
The duration of peak power is less than 10 mS.

Environmental Specifications

Operating temperature: 0°C to +50°C

Storage temperature: -20°C to +80°C

Relative humidity: 10% to 95% non-condensing

Derating: Derate from 100% at +50°C linearly to 50% at +70°C

General Specifications

Turn-on delay time: 2 Sec maxi.

Power factor: 0.9 mini. @ 20% load mini.

Efficiency: 80PLUS GOLD (87%, 90%, 87%)

Hold-up time: 17 mS minimum at 115VAC & 230VAC

Line regulation: ±1% maximum at full load

Inrush current: 50 A @115 VAC at 25°C cold start / 100 A @ 230 VAC at 25°C cold start

Withstand voltage: 4000 VAC from input to output (2 MOPP) / 1500 VAC from input to ground (1 MOPP) / 1500 VAC from output to ground

MTBF: 150,000 hours at full load & 25°C ambient, calculated per MIL-HDBK-217

EMC Performance (IEC60601-1-2)

EN55011/EN55032: Class B conducted, Class B radiated
FCC/VCCI: Class B conducted, Class B radiated
EN61000-3-2: Harmonic distortion, Class A
EN61000-3-3: Line flicker
EN61000-4-2: ESD, ±15 KV air and ±8 KV contact
EN61000-4-3: Radiated immunity, 9-28 V/m
EN61000-4-4: Fast transient/burst, ±2 KV
EN61000-4-5: Surge, ±1 KV diff., ±2 KV com.
EN61000-4-6: Conducted immunity, 3-6 Vrms
EN61000-4-8: Magnetic field immunity, 30 A/m
EN61000-4-11: Voltage dip immunity: 30% reduction for 500 ms, 60% reduction for 100 ms, >95% reduction for 10 ms

Interface Signals

PS_ON: Controls the power supply ON/OFF state.

P.G. (Power Good): Indicates stable power output.

Timing:

T1 (Rise Time): < 20 mS
T2 (Power Good Delay Time): 100 ~ 500 mS
T3 (Power Fail Delay Time): > 1 mS

Mechanical Specifications

Dimensions: 165 mm (Width) x 150 mm (Depth) x 86 mm (Height).

Mounting: 4-#6-32 UNC mounting holes.

Weight: 2.32 Kg

Output Connectors

Description	Cable Length	Connector No.	Output Connectors (equivalent)
Mother board 24 pin	500 mm	P1	MOLEX 39-01-2240
CPU 8 pin	500 mm * 2	P2, P3	MOLEX 39-01-2080
PCI-e 6+2 pin	350 mm * 2	P4, P5	WST P8-I42002, K21B-B
SATA	(500+155 mm) * 2	PE+PF, PG+PH	MOLEX SD-67926-0011, MOLEX SD-67582-0011
PATA	500+155 mm	PA+PB	WST P4-A10202

	FSP Switching Power Supply Safety Certifications for FSP600M-70PB and FSP700M-70PB This document compiles safety and compliance certifications from TUV Rheinland for FSP Group's FSP600M-70PB and FSP700M-70PB switching power supplies. These products are certified for medical applications, tested to IEC 60601-1 standards.
	FSP Power Supplies: UL and CSA Compliance Certificates for Medical and Dental Components Official Certificates of Compliance from UL Solutions for FSP Group Inc. power supplies, including models FSP600M-70PB, FSP700M-70PB, TMPC600-70G, and TMPC700-70G, certified for medical and dental applications under US and Canadian standards.
	FSP Switching Power Supply CE Declaration of Conformity - FSP600M-70PB, FSP700M-70PB Official CE Declaration of Conformity from FSP Group Inc. for their FSP600M-70PB and FSP700M-70PB Switching Power Supplies, confirming compliance with EU Low Voltage Directive (LVD) and EMC Directive.
	FSP1000M-60PG 1000W Medical ATX Power Supply Datasheet Technical datasheet for the FSP1000M-60PG, a 1000W Medical ATX Power Supply. Features IEC 60601-1 & IEC 62368-1 certification, 80 Plus Gold efficiency, and BF class isolation, suitable for medical applications.
	FSP900M-60PJ 900W Medical ATX Power Supply Datasheet \| FSP Technical datasheet for the FSP900M-60PJ, a 900W Medical ATX Power Supply from FSP. Features 1U size, IEC 60601-1 certification, 80 Plus Gold efficiency, and ATX12V V3.0 compliance.
	FSP 500W Medical ATX Power Supplies - MPE Series Datasheet Technical datasheet for FSP's MPE Series 500W Medical ATX Power Supplies, detailing features, specifications, safety approvals, and mechanical dimensions. Includes input/output ratings, environmental conditions, and EMC performance.
	FSP 250W Medical FLEX ATX Power Supply Datasheet Technical datasheet for FSP MPC Series 250W Medical FLEX ATX power supplies, detailing specifications, safety approvals, output ratings, interface signals, and mechanical dimensions.
	FSP PA Series 500W Medical 1U ATX Power Supply Datasheet Technical datasheet for FSP PA Series 500W Medical 1U ATX Power Supplies, detailing features, specifications, safety approvals, and mechanical information for models like FSP400M-80PA and FSP500M-80PA.