SweepScrub SS430C Scrubber User Manual

User Manual for SweepScrub models including: SS430C, SS430C Scrubber, SS430C, Scrubber

The leader in used and preowned cleaning equipment & parts — SweepScrub.com

File Info : application/pdf, 31 Pages, 3.74MB

SS430C Operator and Parts Manual ?v=1747933419

Scrubber User Manual
SS430C

USER MANUAL

TABLE OF CONTENTS

INTRODUCTION .................................................................................................................................................. 2
CONTENTS 2 PURPOSE 2 SPARE PARTS AND MAINTENANCE 2 CHANGES AND IMPROVEMENTS 2 MACHINE APPLICATION 2 UNPACKING/TRANSPORT 2 SAFETY GUIDES 2 TECHNICAL DATA 3

MACHINE DESCRIPTION............................................................................................................................... 4
MACHINE EXPLODED VIEW 4 CONTROL PANEL 5

GUIDE FOR USE ................................................................................................................................................ 5

BEFORE MACHINE START UP 5

BRUSH / PAD-HOLDER INSTALLING AND REMOVAL

SQUEEGEE ADJUSTMENT 5

REGULATING WATER FLOW 6

MACHINE START AND STOP 6

MACHINE OPERATION 7

TANK EMPTYING 7

AFTER EACH USE 8

USING FOR THE FIRST TIME 8

MAINTENANCE AND CARE ........................................................................................................................... 8

SCHEDULED MAINTENANCE TABLE 9

SQUEEGEE CLEANING 9

SQUEEGEE BLADE CHECK AND REPLACEMENT 9

BRUSH/ PAD CLEANING 10

WATER TANK AND FLOAT FILTER SOLUTION FILTER CLEANING

MESHCLEANING1101

TROUBLESHOOTING . .............................................................................................................................. .. 12

PART BREAKDOWNS AND LISTS ............................................................................................... 13-28

WIRING DIAGRAM .............................................................................................................................. 29

USER MANUAL
INTRODUCTION
NOTE Numbers shown in parenthesis correspond with the numbers in the machine exploded view.
CONTENTS
This manual is intended to provide the operator with the necessary information to use this machine properly and safely. The information includes technical data, safety, operation, storage, maintenance and disposal of the machine. All operators and technicians should study this manual carefully before prior to operating or servicing the machine. Please contact your local Viper distributor with any questions.
PURPOSE
The intention of this manual is to educate the operator and service provider on the proper use and maintenance of this machine.
SPARE PARTS AND MAINTENANCE
All necessary operation, maintenance, and repair procedures must be performed by an authorized Viper service provider. Only authorized spare parts and accessories should be used. If service, parts or accessories are needed, please contact your local Viper distributor.
CHANGES AND IMPROVEMENTS
VIPER makes continuous improvements on its products. VIPER reserves the right to change and improve the machines. All changes / improvements should be performed by and authorized Viper service provider.
MACHINE APPLICATION
This scrubber is used in commercial and industrial environments and is suitable for the cleaning of smooth hard floor surfaces. It must be used by qualified operators and in a safe environment. This machine is not to be used outdoors, on carpets, and on coarse floors.
UNPACKING/TRANSPORT
Please follow carefully the instructions on the package when unpacking. Upon delivery, please inspect the packing and the machine to ensure no damage has been done during transport. If there is any visible damage, please contact the distributor you purchased the machine from.
CAUTION
When unpacking and unloading, or during transportation, please take care to avoid hitting the solution valve. Part A in the figure on the right.
Check if the machine is equipped with the following items: Scrubber User Manual
SAFETY GUIDES
The following are special warnings and notices on potential damages (personnel and machine):
WARNING
- Machine may only be operated under the guidance of this manual. Only accessories approved by
VIPER should be used.
2

USER MANUAL
- This machine must be only used by trained & authorized personnel. Children or untrained persons
must not use this machine.
- When working near electrical parts, please do not wear any jewelry. Please take all precautionary
measures to avoid hair, jewelry, and loose fitting clothing from being caught by any moving parts of the machine.
- Prior to scrubbing, it is best to pre-sweep the area to be cleaned. Do not wash the machine directly
with water. Do not let the machine come in touch with corrosive liquids.
- The temperature for storage and for working environment of the machine must be between 0 - 400C. - The humidity of air must be between 30% - 105%. - Please do not use the machine on a slope with a gradient of more than 2%. - In case of fire, please use dry powder fire extinguishers. Do not use liquid fire extinguishers. - Particular attention should be paid when the machine is transported below 00 C. The water tank and
the water in the hoses may freeze and cause serious damages to the machine.
- Use brush or pad driver supplied with the machine and those specified in the owners manual. Using
other brushes or pads could reduce safety.
- In case of machine malfunction, please make sure that it is not caused by lack of maintenance. If it is
caused by other conditions, contact your local Viper authorized service center. If it is confirmed that spare parts must be replaced, please secure the genuine parts from your local Viper distributor.
- In order to ensure safe and proper operation of the machine, it is advised that your Viper authorized
service provider perform the scheduled maintenance according to the maintenance schedules outlined in this manual.
- This machine must be properly disposed of in accordance with local laws and regulations (please
refer to machine disposal section).
TECHNICAL DATA

Model
Machine Height Solution tank capacity Recovery tank capacity Diameter of transport wheel Diameter of guide wheel Power of vacuum system motor Maximum gradient when working Sound pressure level at workstation Cable length Vacuum system circuit capacity Cleaning width Squeegee width machine maximum length Machine width without squeegee Brush diameter Weight with empty tanks Gross weight of the machine ready for use Brush motor power Brush speed Brush /pad-holder Maximum pressure
Packing size (Lx W x H)
Vibration level at the operator's arms (ISO 5349-1, EN 60335-2-72)

AS430C
980mm 50 litre 50 litre 200mm 63.5mm 400w
2 (Max) 72dB(A ±3dB(A)
20m 1200 mm H2O
430mm 760mm 1060mm 480mm 430mm
70kg 120kg 750W 150rpm 32kg (Max)
1200 x 610 x 1170mm
2.5 m/s2

USER MANUAL
MACHINE DESCRIPTION
MACHINE EXPLODED VIEW 1. Safety switch button 2. Handle 3. Control panel
4. Serial number plate/Technical data
5. Control cover 6. N/A 7. N/A 8. Reset switch 9. Power cable 10. Battery cover 11. Drain hose 12. Squeegee lift cable 13. N/A 14. Squeegee lift handle 15. Drain cap 16. Squeegee knob 17. Squeegee clip 18. Squeegee blade 19. Squeegee bracket

20. Squeegee adjusting knob 21. Squeegee rear support frame 22. Squeegee front support frame
23. Cup holder
24. Recovery tank cover handle 25. Recovery tank lid 26. Recovery tank 27. Solution fill 28. Brush deck 29. Brush / pad-holder 30. Vacuum motor 31. Brush motor 32. 8" wheel 33. N/A 34. Vacuum tube 35. Electric box 36. Float filter 37. Water level site tube

Figure 1
4

CONTROL PANEL (Figure2)
38. Power switch 39. Vacuum switch 40. Solution switch

USER MANUAL

Figure 2

GUIDE FOR USE

WARNING On certain parts of the machine are pasted some indicative signs:
DANGER WARNING CAUTION CONSULTATION

When reading this manual, the operator must pay particular attention to the symbols on these labels. Under no circumstances shall these labels be covered. If they are damaged, please replace them immediately.

BEFORE MACHINE START-UP
BRUSH / PAD-HOLDER INSTALLING AND REMOVAL
NOTE According to the type of floor to be cleaned, the machine may be installed with brush (Figure 3, A), or a pad-holder (Figure 3, B and C).
CAUTION
When manually installing or removing the brush/pad-holder, first ensure that all the switches are in the "off" position and lift the squeegee off the floor. Only after which can the brush or pad-holder be worked on. Always wear protective gloves.

1. (Only applicable to AS430C ): make sure the power cable (9) disconnecting the power supply and the switch (38) is at the disconnecting (Off) condition.
2. Press down the handle (2) to lift the tank body (26). 1. Put the brush (A) or the pad-holder (B C) under the case. 2. Use the handle (2) to lower the tank body (26) to come into
contact with the brush or pad-holder. 3. Manually attach by following the arrow head (D) to install
the brush/pad-holder (as shown in Figure 3). 6. Remove by turning the brush/pad-holder in the opposite
direction and it can be taken off. (Figure 3)

SQUEEGEE ADJUSTING

Figure 3

7. Install the squeegee and tighten the knobs. Then connect

the vacuum hose to the squeegee assembly..

8. Adjust the squeegee through the adjusting handle (A) of the squeegee (Figure 4).

1) If the mid-section of the rear squeegee bracket, section B, has a gap with the floor or the

downward pressure is relatively light, adjust the handle in an anti-clockwise direction until the

USER MANUAL
whole length of the rear squeegee strip touches well with the floor. The front squeegee strip should lightly touch the floor. 2) If the two ends of the rear squeegee strip, sections C and D, have a gap with the floor or the downward pressure is relatively light, adjust the handle in a clockwise direction until the whole length of the rear squeegee strip touches well with the floor. The front squeegee strip should Lightly touch the floor.

Solution tank filling

Figure 4

CAUTION
Only low foam, nonflammable detergents may be used. These detergents must be suitable for the use of scrubbers.

9. Open the water inlet cover (27) and add water to solution tank. Do not overfill the tank. When preparing the cleaning solutions, please follow the dilution rates supplied by the chemical manufacturer Water temperature must not exceed 400 C.

REGULATING WATER FLOW
WARNING
Regulating the ball valve handle (A, Figure 5) must be done under the condition when the power switch (38) is in the "Off" position.

10. The volume of the water flow may be adjusted through the ball valve handle (A, Figure 5) according to the amount of water required for your scrubbing application.
MACHINE START AND STOP

Figure 5

Starting the machine
1. Complete the preparatory steps as outlined above.
2. Press the power switch (38) to the "I" position. 3. Use the squeegee handle (38) to lower the squeegee. 4. Press the Vacuum switch (39) to the "I" position. 5. Press the solution switch (40) to the "I" position. (Work simultaneously with the safety switch (1)
to control the solenoid valve.) 6. Squeeze the on / off switch (1) and push to move the machine. When switches are squeezed, the
brush (29) will to rotate, and the solution will flow.

CONSULTATION
Each safety switch is capable of controlling independently the operation of the brush. In use, it facilitates the control of the operation of the machine.
Operators are encouraged to find the most comfortable position their hands.

USER MANUAL

Turning off the machine 7. When you have finished using the machine, first remove the
brush/pad-holder (refer to the steps mentioned above) 8. Release the safety switch (1) to turn off the brush/pad-
holder and solenoid valve. 9. Press the Vacuum switch (39) to the "Off" position, and the
Vacuum will delay for 5 seconds before stopping work. 10. Press the solution control switch (40) to the "Off" position
to completely turn off the solution flow. 11. Press the power switch (38) to the "Off" position. And
disconnecting the power cable (9) from the power supply. 12. Use the squeegee lift handle (14) to lift the squeegee. 13. Grasp the handle (2) and gently tilt the machine backward
until the guide wheel (B) touches the floor. See Figure7.

Figure 6

MACHINE OPERATION

Figure 7

1. Start the machine according to the description above. 2. Hold the on / off switch (1) (Figure 6), push to move the machine, and start the scrubbing. 3. If necessary, turn off the machine, and adjust the squeegee. (Refer to the steps for squeegee
adjustment) 4. If necessary, turn off the machine, and adjust the solution flow with the ball valve handle. (Refer
to the steps for adjusting solution flow.

CAUTION
In order to avoid damaging the floor, when the machine stays in one place without moving, remove hands from switches & turn off the main power switch (38).

TANK EMPTYING
When recovery tank is full, a float shut-off device (36) will block the inlet connecting to the vacuum motor. Through a sudden increase of noise from the vacuum motor, it can be considered that the recovery tank is full and requires immediate draining.
CAUTION
If the vacuum motor is suddenly turned off (due to sudden movement resulting in an activation of the float), and if a resumption of operation is needed, please perform the following steps: press the power switch (38 and 39) to turn off the power and the vacuum motor, and open the recovery tank cover (25) to check if the float has returned to the water surface. Close the recovery tank cover (25), and press the power switch (38 and 39) to turn on the main power and the vacuum motor.

Recovery tank emptying 1. Turn off the machine. 2. Raise the squeegee assembly (14). 3. Move the machine to a dedicated draining location. 4. Grasp the handle (2) and tilt the machine backward until the guide wheel touches the floor. 5. Remove the drain hose from the clip, bend the top end of draining hose (A, Figure 8), and then remove the drain hose cap. Lower the hose to a low level or on the ground to drain the water. Alternatively, place drain hose to a low position or on the ground to make the water outlet face

USER MANUAL

downward (B, Figure 8), and then twist open the drain cap to drain the wastewater in the tank. After draining is completed, rinse the inside of recovery tank with clean water
CAUTION
When draining the wastewater, the drain hose must be folded or lowered to a lower position (Figure 8 A or B), and the cap removed for wastewater to drain. Do not allow the opening of the drain hose to face upward, as it could get wastewater on the operator..
Solution tank emptying 6. Complete Steps 1 to 4. 7. As shown in Figure 9, turn open the lid of Solution tank (A) counter
clockwise (direction C), to drain Solution tank completely. Use clean water to rinse the inside of Solution tank. When work is completed, replace the solution tank lid (A) by twisting in a clockwise in direction (B).

Figure 8

AFTER EACH USE
When work is done and before leaving the machine, completes the following steps: 1. Remove the brush / pad holder. 2. Drain solution tank & rinse with clean water. 3. Drain recovery tank & rinse with clean water. 4. Complete the daily maintenance procedures. (see maintenance
section) 5. Remove and rinse squeegee assembly with damp towel. 6. Keep recovery tank lid unsealed from tank to allow fresh air to
circulate freely

Figure 9

USING FOR THE FIRST TIME
After the first 9 hours of use, please check components to ensure all connections (electrical & mechanical) are tight & check for any damage that may have occurred during operation. Check for water leakage.

MAINTENANCE AND CARE
The service life and the maximum operation safety of the machine are assured by proper and timely maintenance and care.

The following table is a routine maintenance guide for the machine. The time intervals of maintenance are determined to a large extent by the working conditions of the machine. These time intervals should be formulated by the person responsible for the maintenance.
WARNING
Only after the main power is disconnected should these procedures be performed. Prior to proceeding with any of the maintenance procedures, please study carefully the related safety sections.

All maintenance should be done by qualified personnel or authorized Viper service centers. This manual only relates the simplest and the most common maintenance procedures. For any maintenance procedures other than those stated in this table of planned maintenance, please contact your local Viper distributor.

USER MANUAL

SCHEDULED MAINTENANCE TABLE

Procedure

Daily,

Weekly Every Annually

Machine

6 months

after use

Clean squeegee

Clean brush/pad-holder

Clean water tank and float filter, inspect

tank gaskets

Inspect and change the squeegee blades

Clean solution filter

Clean vacuum motor filter

Inspect tightness of nuts and bolts

(1)

Inspect or change motor carbon brush of

(2)

brush motor

Inspect or change carbon brush of Vacuum motor

(2)

(1) It should be done 9 hours after the machine starts working.

(2) These maintenance procedures must be done by an authorized VIPER Service Center.

SQUEEGEE CLEANING
NOTE In order to maintain the optimal squeegee performance, the squeegee must be kept clean, and the squeegee blades must remain in good condition.
CAUTION
When cleaning the squeegee, it is recommended to put on protective gloves as the squeegee may contain sharp debris.
1. Move the machine to a flat and smooth surface. 2. Press the power switch (38) to the "O" position to turn off the machine. 3. Unscrew the squeegee knobs (16); remove the vacuum hose from the squeegee assembly &
remove squeegee. 4. Use the squeegee lift handle (14) to lift the squeegee mount bracket. 5. Using a damp towel, clean the squeegee (Figure 10). Clean in particular the groove (A, Figure
10) and the dirt and fragments on the vacuum tube. Check if the front squeegee blade (C) and the rear squeegee blade (D) are intact, and if there are broken edges and cracks. Replace them if necessary (refer to the steps in the following section). 6. Re-install the squeegee in the reverse order of the above
SQUEEGEE BLADE CHECK AND REPLACEMENT
1. Following the methods related in the previous section clean the squeegee (Figure 10) 2. Check the edge (E, Figure 10) of the front squeegee blade and the edge (F) of the rear squeegee
blade (D). On the whole length, they should be level. Otherwise, adjust their heights through the
following procedure. Loosen the clip (G) to let the rear squeegee blade (D) separate from the bracket (M) for the
adjustment of the position of the squeegee. After the adjustment, lock the clip once again. Loosen the screw on the handle (I) to adjust the front squeegee blade (C); tighten the handle screw after adjustment. 3 Check if the front squeegee blade (C) and the rear squeegee blade (D) is intact and if there are broken edges and cracks. If damage is found, change them according in the following way. If the front edge of the rear squeegee blade (J) has worn, it can be flipped upside down and re-installed (the top edge is required to be intact). If the top edge is also worn, change it by following the
procedure below: Loosen the clip (G) to let the pressure blade separate from the bracket (M), take off the clip bar (K), and then change or turn the rear squeegee blade (D) upside down. Re-install the rear squeegee blade in the reverse order of taking it off.
9

USER MANUAL
Loosen the handle screw (I) and take off the front clip bar (L), and then change the front squeegee (C). Re-install the front squeegee blade in the reverse order of taking it off. After changing the squeegee blade, adjust the level of the front and rear squeegee blades in the procedures as described above. 4. Connect the Vacuum hose (11) to the squeegee. 5. Install the squeegee and tighten the knobs. 6. If necessary, adjust the squeegee by turning the adjustment knob (20) (refer to the procedures for adjusting the balance of the squeegee).
Figure 10
BRUSH/ PAD CLEANING
CAUTION
When cleaning the brush/pad-driver, wearing protective gloves is Recommended as the brush / pad may contain sharp debris. 1. Remove the brush/pad-driver. 2. With the use of water and detergents, clean the brush/pad driver. 3. Check the brush for wear & if necessary, replace the brush. 4. Check the pad driver for wear & if necessary, replace the pad driver.
WATER TANK AND FLOAT FILTER MESH CLEANING
1. Move the machine to a dedicated draining area. 2. Press the power switch (38) to the position "O" to turn off the machine. 3. Open recovery tank lid (A, Figure 11), and remove the float device (36) from inside the tank. 4. Use clean water to rinse the recovery tank lid (A), the tank (B and C), and the float filter support
frame (E). Drain all the water from the water tank. 5. If necessary, following the symbols "Open" and "Close" as shown in Figure 11, open the bottom
lid (F) of the float filter and clean the float (D), float filter support frame (E), and the filter sponge (I). After cleaning, re-attach the float onto the support frame (E), and then align the mark groove (L) of the bottom lid (F) of the float filter with the mark groove (L) of the float filter support frame (E). Turn the bottom lid (F) of the float filter tight, and re-attach the filter sponge (I) onto the support frame (E), and then onto the vacuum tube (M). 6. Inspect the seal / gasket (G) of the recovery tank lid.
NOTE The seal / gasket (G) of the recovery tank allows the tank to create a vacuum. It must be completely sealed to be able to effectively suck the wastewater from the floor.
If necessary, If necessary, the recovery tank seal / gasket (G) may be taken out from the groove (H) and changed. When installing the new seal / gasket as shown in Figure 11 below, install the
10

USER MANUAL
connector to the middle section of the rear part. 7. Check if the receiving surface of the sealing strip (G) is intact and seals adequately. 8. Close recovery tank lid (A).
Figure 11
SOLUTION FILTER CLEANING
1. Drain all the water from Solution tank as previously outlined. 2. Move the machine to a flat and smooth surface. 3. Press the power switch (38) to the "O" position to turn off the machine. 4. Turn off the draining ball valve (A, Figure 12) (located at the bottom of the machine, behind the
wheels). Position B ball valve open, and position C ball valve closed. 5. Remove the transparent cap (D), and then take off the filter (E), and install them onto the filter
box (F) after cleaning. NOTE The filter (E) must be accurately installed onto the position of the housing (G).
6. Open the draining ball valve (A).
Filter Mesh Mark Figure 12
11

USER MANUAL

TROUBLESHOOTING

Breakdown

Probable Causes

Remedies

Machine not working

The wiring not connected correctly or bad wiring
Bad brush motor Carbon brush worn out

Check the wiring or contact Viper Distributor
Contact Viper Distributor Contact Viper Distributor

Vacuum motor not working
Little or no solution flow

The wiring not connected correctly or bad wiring
Bad vacuum motor Carbon brushes worn out Bad ball valve Bad solution valve
Ball valve position in need of adjustment

Check the wiring or contact Viper Distributor
Contact Viper Distributor Contact Viper Distributor Contact Viper Distributor Contact Viper Distributor
When ball valve is in horizontal position, the amount of solution flow is maximum

Inadequate Vacuum
Squeegee leaving marks

Filter dirty.

Clean the filter

Wastewater tank is full.
Vacuum tube for waste and squeegee not properly connected
Float filter blocked or inlet blocked
Squeegee dirty or squeegee blade worn and damaged Recovery tank lid not properly turned on, or the sealing strip of the water tank damaged
Debris like fragments under the squeegee blade
Squeegee blade already worn, cracked, brittle.

Drain the water tank Connect the Vacuum tube for waste and the squeegee Clean the float filter, check the float ball Clean and check the squeegee
Refit on the lid properly, or change the water tank sealing strip
Remove the fragments
Change the squeegee blade

Balance of squeegee not adjusted

Adjust the balance

TANK SYSTEM AS430C PART LIST

Item 1 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34

Part No. VF90535 VF90504 VF90619 VF90612 VS10439 VF90616 VA13483A VA13477 VF90611 VF90519 VF90011 VF90613 VF90617 RD60764 VA80770 VF90727 VF85319 VF90523 VF13503 VF90511 VF14543 VV13601 VA13474 VF14066 VF90434 VF90513 VF90507 VF90312 VF14551 VF90306 VF90308 VF90314

Revised 04/2022

Description

Qty

RECOVERY TANK KIT

GASKET

TANK FILTER NET KIT

FILTER COVER

ZIPPER

SCREW TA3.5X12

WASHER

SCREW ST4X15

FILTER SUPPORT

TANK (CABLE MODLE)

LOGO LABEL

FLOATING BALL OF WATER LEVEL

INSPECTION TUBE

ELBOW 90º BRASS

GASKET

VACUUM MOTOR KIT

ACOUSTIC INSULATION PIPE TOP

GASKET OF SUCTION MOTOR NUT

LOCK M8

COVER, VACUUM MOTOR WASHER

6*18*1.5

WASHER,LOCK,Ø5

SCEREW M5*16

NUT M8

SCEREW M8*65

OUTLET O-RING

OUTLET COVER

2.5" WHEEL KIT

RING D 17

2.5" WHEEL

2.5" HUB CAP

TRANSPORT WHEEL SHAFT

# = Revised or new since last update 14

TANK SYSTEM AS430C PART LIST

Item
35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69

Part No. VV10116 VF85102 VF13604 VF90235 VF90508 VF90231 VF90214 VF90217 VA80758 VF90529 VF90528 VF90512 VF90509 VA20304 VF90534
VF90218 VF90401 VF90443 VF83150 VF90701 VF13534 VF13519 VF14067 GT13054 VF90814 VF90720 VF90730 VF90721 VF90522 VS10007 55943353

Revised 05/2023

Description

Qty

SELF-LOCKING NYLON CABLE TIES

CLAMP

GROOVED METAL GASKET SCEREW

TM4x10

SUCTION HOSE

GASKET

SEAL PLATE COVER

SEAL PLATE

SCREW

Vacuum Hose Connector

Squeegee Hose Connector SUCTION

TUBE GASKET

SEALING KNOB

CLAMP

FLOAT CAGE COMPLETE

SPONGE

FLOAT CAGE

FLOATING BALL

FLOAT CAGE COVER

CONTROL SEAL GASKET

DRAIN HOSE CONNECTER

DRAIN HOSE-38

HOLDER,"U"HOSE

17"COUNTER WEIGHT BLOCK

WASHER

WASHER,LOCK,Ø8

SCREW M8*25

SCREW TM5x12

BATTERY COVERY

VACUUM MOTOR CONNECTION LINE

SOLENOID VALVE CONNECTION LINE

BRUSH MOTOR CONNECTION LINE

CARBON BRUSH KIT

ACOUSTIC INSULATION PIPE

RECOVERY LID STRAP KIT

# = Revised or new since last update

CONTROL SYSTEM AND ELECTRICAL SYSTEM AS430C PART LIST

Revised 03/2018

Item

Part No.

Description

Qty

VF90203

SAFETY SWITCH KNOB

VF90286

SCREW KA3.5x12

VF90201

SAFETY SWITCH COVER LEFT

VV68303

SCREW KA3.5x15

VF90288

WASHER 3.6X8X0.5

VF90210

SWITCH FIX FRAME

VV60153

SWITCH RL2P

VF90009

DECAL CONTROL PANEL

VF90235

SCREW TM4x10

VF90204

17" SWITCH COVER

VF90706

24VDC REGULATOR BOARD

VA14584

SCREW PB3.0x8

VF90285

SWITCH SEAL STRIP

VF90216

SWITCH SEAL BUSHING

VF90202

SPRING

VF90252

SWITCH

VF90212

SAFETY SWITCH COVER RIGHT

VF90219

GASKET

VA13469

SCREW PB3x12

VF90213

SWITCH SEAL RING

GT13091

SCREW,PB3.5x9.5mm

VF89042-3

RELAY

GT13025

SCREW,M3X12

VF90725-1

RUNNING CAPACITOR

VF90815

COVER CONTROL HOUSING

GT13054

SCREW TM5x12

N/A

17" SERIAL NUMBER LABEL

VF90275

CLAMP DRAIN HOSE KIT

VF90027

BACK COVER PANEL

VF90129

SCREW M5x20

VF90113

HANDLE LIFT

VF14514

NUT LOCK M5

# = Revised or new since last update 17

CONTROL SYSTEM AND ELECTRICAL SYSTEM AS430C PART LIST

Item
34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

Part No.
VF90128 VF90114 VF89076 80407A VF90116 VF90704 VV13652 VV13653 VF90232 VF90725-2 VF90259 VF99010C VF90517 VF73705 VF90745 VV67105 VF90703-US VF422997 VV13667 VF13604 VF90019 VF90747 VF90020

Description

Qty

SCREW M5

CABLE SQUEEGEE LIFT

CIRCUIT BREAKER CAP

SCREW M5X25

HAND BRACKET

24V RELAY

NUT LOCK M3

WASHER Ø3.4xØ10x1.0mm

ELECTRIC SUPPORT

START CAPACITOR

HAND FIX PANEL

CIRCUIT BREAKER

CABLE FIX BRACKET

CABLE SLEEVE

POWER CORD

BLOCK JOINING POWER CORD TO MACHINE CORD 1

CABLE (20M)

BELT HANGER F POWER CORD

SCREW TM4x8

GROOVED METAL GASKET

BRUSH CIRCUIT LABEL

CIRCUIT BREAKER

VACUUM CIRCUIT LABEL

WHEELS AND SOLUTION SYSTEM AS430C PART LIST

WHEELS AND SOLUTION SYSTEM

AS430C PART LIST

Item

Part N

Descripti n

Qty

VF89203

WHEEL COVER

VF14563

LEVILLE WASHER

VF14554

WASHER

VF90304

WHEEL SHAFT

VF82172

SPRING 70

VF90305

8" WHEEL

VF14552

RING D 17

VF90284

SOLENOID VALVE KIT

VV10114

CLAMP

VF90440

TUBING L=260mm

VF90604

FILTER BASE

VF90608

FILTER NET

VF90607

0-RING

VF90603

FILTER COVER

VF90621

FILTER KIT

VA13507

SCREW ST4x12

VF90441

TUBING L=160mm

VF90625

SOLENOID VALVE BRACKET

VA13483

WASHER12.5*1.5

VV13650A

SCREW M4x10

VF80313

BARB,HOSE

VF80361

BALL VALVE

VF90609

ELBOW,90°,BRASS

BRUSH SYSTEM AS430C PART LIST

Item
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31

Part No.
VF90729 VF90284 VF90418 VV13650A VV20274 VF90460 VF90461 VF90421 VF14555 VF14238 VA13479 9098809000 VS10340 VV13604 VF90406 VF14506 GT13067 VF90465 VF90424 VF90422 ZD45425 VF90423 VV13650A VV20291 VF90437 VF90463 VF90425 VF90415 VF13535 VV20298 VF90462

Description
BRUSH MOTOR KIT SOLENOID VALVE KIT SOLENOID VALVE BRACKET SCREW M4x10 WASHER CONNECT PLATE C BRASS SPACER B SPACER SCREW,SHOULDER M12x50 SCREW, M12x30 SCREW M6X30 SLEEVE 25*10*9MM BUMPER ROLLER SCREW,SHOULDER M8x20 17" BRUSH DECK NUT LOCK M6 SCREW,SHOULDER M8x25 DRIVEN PULLEY KIT NUT M20 SPACER BEARING 6204 LU CLAMP SLEEVE SCREW M4x10 WASHER,LOCK,Ø4 BRUSH SPRING CLIP DRIVEN PULLEY DRIVEN PULLEY SHAFT VIBRATION GASKET WASHER 8.1x 20x 2 WASHER,LOCK,Ø8 BELT

Revised 11/2017
Qty
1 1 1 4 2 1 2 4 4 2 2 2 2 4 1 2 2 1 2 1 2 1 2 2 1 1 1 1 1 1 1

# = Revised or new since last update 22

BRUSH SYSTEM AS430C PART LIST

Item
32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

Part No.
VF13503 VF14057A VF90459 VF90455 VF13538 VF13541 VV20298 VA13491 VF90445 VF14516 VF13535 VF999821A VF90072 VF80209 VF80214 GT13066 VF90427 VF80232 VF80235 VF14255 VF14236 VF13535 VF90439 VF90438 VF90411 VF90428 VF85128 VF14543 VF13540 VF90466 VS10131 VF99003A VF90453

Description
NUT LOCK M8 NUT LOCK M12 SLIDING CONNECT PLATE FRAME WASHER 12x24x2 WASHER,LOCK 12 WASHER,LOCK,Ø8 SCREW, M8x25 TENSION WHEEL KIT NUT LOCK M8 WASHER 8.1x 20x 2 BEARING 6002 TENSION WHEEL SPACER SPACER SCREW,SHOULDER M8x55 ROD, TENSION WHEEL SPRING SPACER SCREW, M12x65 SCREW, M8x40 WASHER 8.4x 18x 2 BUSHING TENSION WHEEL SCREW,SHOULDER M8x30 17"BRUSH 17 INCH PAD CAP BLACK WASHER Ø6*Ø18*1.5mm WAVE WASHER Ø6 17" SKIRT KIT RETAINER PAD KIT RETAINER PAD 17" PAD WITH RETAINER

Revised 11/2017
Qty
9 3 1 1 1 3 4 3 1 1 1 2 1 1 1 1 1 1 1 1 1 2 2 1 1 1 2 4 2
1 1 1 1

# = Revised or new since last update 23

SQUEEGEE SYSTEM AS430C PART LIST

Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
*18#
19 20 21 22
23 #
24 25 26 27
28 # *28 # 29 # *29 #
30

Part No. VF14547 VF85143 VF13514A VF14503 VF90133 VF90110 VF14516 VF14506 VF13533 VF90111 VF85336 VF14525 VF81210 VF84228 VF82112 VF14233 VF90109 VF90134 VF90136 VV20203 VF81219 VF81222 VF90102 VF90137 VF14530 VF85107 VF85134 VF90103 VF90146 VF90104 VF90147 VF85420

Revised 04/2024

Description

Qty

SCREW LOCK M10

HAND WHEEL

WASHER 8x 16.5x 1

NUT M8

SPACER

BACK-SQUEEGEE-SUPPORT

NUT LOCK M8

NUT M6

WASHER FLAT Ø6

FRONT-SQUEEGEE-SUPPORT

WASHER NYLON

SCREW SHOULDER

KNOB

SCREW SHOULDER M8

SPACER

SCREW

SQUEEGEE-SUPPORT

SQUEEGEE KIT-710MM 28IN ALU

SQUEEGEE ROLL WHEEL KIT

NUT LOCK

2" WHEEL

BOLT SHOULDER 5/16"

STRAP-SQUEEGEE FRONT-28IN

BUMPER ROLLER KIT

SCREW M6×40

BUMPER ROLLER

SPACER

BLADE FRONT-NR-710MM 28IN

BLADE FRONT-PU-710MM 28IN

BLADE REAR-NR-710MM 28IN

BLADE REAR-PU-710MM 28IN

WING NUT M8×30

# = Revised or new since last update * = Optional NOTE : Item 19-39 are only used on item 18.
25

SQUEEGEE SYSTEM AS430C PART LIST

Item 31 # 32 33 # 34 35 36 37 38 39 # 40 41

Part No. VF90101 VF90127 VF90138 VF14305 VF90121 VF81208A VF81218A GT13022 VF90105 VF13519 VS10518

Revised 04/2024

Description

Qty

SQUEEGEE TOOL-710MM 28IN ALU

SQUEEGEE SCREW

STRAP-SQUEEGEE BACK KIT-28IN

SCREW M5×60

HOOK

RIVET Ø4×5

LATCH HOOD

NUT LOCK M5

STRAP-SQUEEGEE BACK-28IN

WASHER,LOCK,Ø8

SPRING

# = Revised or new since last update * = Optional NOTE : Item 19-39 are only used on item 18.
26

8 K4
9

K3
18 12 13 14 15 16 17
K5

SQUEEGEE SYSTEM AS430C PART LIST

Kit
K2 *K2 K3 K3 K3 K3
K4 K4 K2 *K2
K5 K5 K5 K5 K5 K5 K5
K1# K2# *K2# K3# K4# K5#

Item 1 2 2 3 4 5 6 7 8 9 10 10 11 12 13 14 15 16 17 18 19

Part No. 559503017
559503020
559503022
VF81210 559503016 559503018 559503024 559503019 559503023 559503021

Revised 04/2024

Description

Qty

STRAP REAR KIT-SQGEE-NBR

BLADE REAR-NR-760MM 30IN

BLADE REAR-PU-760MM 30IN

BLOCK

SCREW SS PB5X25

WASHER PLAIN 6X18X1.5 SS

3.5" BUMPER WHEEL

SQGEE TOOL KIT-760MM 30IN PLAST

2" WHEEL

SPACER Ø6.3XØ9.5X25MM

BLADE FRONT-NR-760MM 30IN

BLADE FRONT-PU-760MM 30IN

STRAP FRONT KIT-SQGEE

NUT HEX M8 SS

WING NUT M8X30MM

WASHER 304 Ø6.3XØ12.6X1.2MM

NUT LOCK SS M6

BOLT, M6X45, HEX STAINLESS

SCREW M8X65MM

NUT LOCK M8 SS

KNOB

SQUEEGEE KIT-760MM 30IN PLAST

BLADES KIT-NR-30IN

BLADES KIT-PU-30IN

ROLLER BUMPER KIT

ROLLER KIT

HARDWARE KIT

# = Revised or new since last update * = Optional
28

WIRING DIAGRAM AS430C PART LIST
29

PDFium PDFium