Hama Fullmotion TV Wall Bracket

1. Explanation of Warning Symbols and Notes

Warning
This symbol ⚠️ is used to indicate safety instructions or to draw your attention to specific hazards and risks.

Note
This symbol ⓘ is used to indicate additional information or important notes.

2. Package Contents

• TV wall bracket
• VESA arms (2x)
• Wall plate cover (2x)
• Cable management
• Drilling template
• Mounting kit
• Safety instructions, illustrated quick start guide

Mounting Kit Components:

• A1: 8x70 mm screws (x6)
• A2: Ø10x60 mm plugs (fischer) (x6)
• A3: M8 screws (x6)
• B1: M6 screws (x4)
• B2: Ø8x10 mm screws (x4)
• B3: Ø8x20 mm screws (x4)
• C1: M6x12 mm screws (x4)
• C2: M6x20 mm screws (x4)
• D1: M8x12 mm screws (x4)
• D2: M8x20 mm screws (x4)
• D3: M8x30 mm screws (x4)
• D4: M8x50 mm screws (x4)
• F1: Screws (x4)
• F2: Spirit level (x1)
• F3: Pencil (x1)
• G1: Pipe socket spanner (x1)
• G2: (x1)

Note: Please check the mounting kit for completeness before installing the bracket and ensure that there are no faulty or damaged parts.

3. Additionally Required Tools

• Drill
• 10 mm drill bit
• Spirit level (if not included in kit)
• Pencil (if not included in kit)
• Screwdriver (appropriate type)
• Assistance from another person

Note: Never install the bracket alone. Seek assistance and help!

4. Safety Instructions

Warning:

• The supplied mounting kit may not cover all wall structure options.
• Screws for attaching the device to the bracket may occasionally be too long.
• Wall plugs are for use with solid, hollow, and board construction materials only.
• Read your terminal device's operating instructions for information on suitable fastening materials.
• If the mounting kit lacks suitable fastening materials, purchase them from a specialized dealer.
• Never apply force during assembly to avoid damaging your device or the holder.
• If in doubt, have this product installed by a qualified technician.
• Do not mount the product above areas where people might sit or stand.
• After mounting, check that the product and attached load are secure and safe. Repeat this check at least quarterly.
• Ensure the product's maximum carrying capacity and dimensions are not exceeded.
• Load the product symmetrically.
• Maintain necessary safety clearance around the attached load.
• In case of product damage, remove the load and stop using the product.
• Do not attach additional objects to the product.

5. Application and Specifications

• The bracket is used for mounting flat screens in private, non-commercial households.
• The bracket is intended for indoor use only.
• Use the bracket only for its intended purpose.

6. Preparation and Assembly

Note: Never install the bracket alone. Seek assistance and help!

Check that necessary connections on your end device are accessible after mounting.

You may not need all mounting kit parts depending on the product and mounting method. Keep any leftover parts for future reference.

Warning: Brackets are only suitable for wall mounting. Before installation, ensure the wall is suitable for the weight and free of electrical, water, or gas lines.

Note - Fischer Plugs

The supplied Fischer plugs are approved for the following building materials:

• Concrete
• Plasterboard and gypsum fibreboard
• Vertical perforated brick
• Lightweight concrete hollow block
• Hollow brick and concrete ceilings
• Perforated sand-lime brick
• Solid sand-lime brick
• Natural stone
• Aerated concrete
• Chipboard
• Solid plaster boards
• Lightweight concrete solid block
• Solid brick

6.1 Mounting on the Wall

6.1.1 Preparing the intended mounting surface

Get support and help from other people for the following assembly steps.

Use the enclosed drilling template to determine the bracket's position. Use a spirit level [F2] to check horizontal and vertical alignment. Mark the holes on the wall using a pencil [F3].

For wall attachment, use a drill with a 10 mm drill bit. Ensure the drill bit is suitable for the wall type. The hole depth should be 70 mm.

To ensure a secure hold, vacuum out drill holes to remove dust. Insert the plug [A2] into the drill hole until it is flush.

6.1.2 Attaching the wall bracket

Attach the wall bracket to the wall using the enclosed mounting material: plug [A2], M8 washer [A3], 8x70 mm screw [A1], pipe socket spanner [G1], and spirit level [F2].

Attach the two enclosed covers to the bracket.

6.2 Mounting on the TV Set

Note: Due to the variety of terminal devices, not all mounting options can be described here.

Ensure the bracket lays flat and evenly on the back of the television.

Use the enclosed spacers to even out any unevenness on the TV's back.

Ensure all screws have the proper length and can be mounted hand-tight.

6.2.1 Mount the VESA arms on the back of the TV set

Before installation, ensure the grooved side of the VESA plate is pointing upwards.

Mount the VESA arms to the back of your TV set. Note the correct combination of screw, washer, and spacer for your flat or curved TV:

Flat TV Back:

Use F1 + B1 + C1, D1, or D4 screws.

Curved TV Back:

Use F1 + B1 + C2, D2, or D4 screws.

For curved TVs, use F1 + B2 or B3 + D3 or D4 screws.

Note: You do not need a washer for the D-screws.

Example calculation: M8x50 screw + Ø8x5 spacer = M8x45 (D4 screw).

6.3 Mounting the TV on the wall bracket

Get support and help from other people for this assembly step. Adjust joints during installation to allow for lateral TV movement.

Pull the securing cord downwards and hang the TV set with the mounted VESA arms onto the wall bracket until it audibly engages. The ends of the securing cords can be fastened to the wall bracket using magnets ?.

6.4 Mounting the cable management

Run cables along the wall bracket arms and cable guides.

Attach the cable manager to the bracket arm until it clicks into place.

7. Adjustment & Maintenance

Note: Never adjust the bracket alone. Seek assistance and help!

Note - Tiltable / Full-motion brackets:

• Ensure no electrical cables are crushed or damaged during installation or adjustment.
• During adjustment, ensure the product is loaded symmetrically and does not exceed its maximum carrying capacity.
• Check the bracket's strength and operational safety, along with the attached load, at regular intervals (at least quarterly).
• Clean only with water or conventional household cleaners.

8. Setting Options

• Swivel: Up to 120° (depending on device, at 3 joints with 2 double supporting arms)
• Extendable: 55 - 449 mm
• Tilting: -10°/+2° (depending on device)
• Rotating: 6°

No screws need to be loosened to adjust the tilt.

9. Technical Data

10. Warranty Disclaimer

Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product, or failure to observe operating instructions and/or safety notes.

11. Service and Support

For product questions, please contact Hama Product Consulting. Hotline: +49 9091 502-0 (German/English). Further support information can be found at: support.hama.com ?.

12. Warranty Conditions

HAMA GmbH & Co KG grants a 10-year manufacturer's warranty for freedom from defects, usability, workmanship, and material durability. This warranty excludes compatibility with future hardware standards. Hama GmbH & Co KG will remedy justified warranty claims at its discretion, free of charge, through repair or replacement. The warranty period begins on the date of purchase and is valid throughout the EU. This warranty is in addition to and does not affect your statutory rights. Damage from improper use, normal wear and tear, chemical exposure, force majeure, or tampering/repairs by unauthorized parties is excluded. Accessories not part of the basic equipment are also excluded. For warranty claims, contact Hama GmbH & Co KG, Dresdner Str. 9, 86653 Monheim, Germany, with proof of purchase. You can also contact support.hama.com or call +49 (0)9091/502-0.