Crosley CR8017A Voyager Turntable Instruction Manual

Safety Instructions

Read and understand this entire manual before using this product. Keep these instructions for future reference.

1. Do not use this product near water.
2. This product should be operated only by the type of power source indicated on the marking label or in this instruction manual.
3. Do not defeat the safety purpose of the polarized plug. A polarized plug has two blades with one blade wider than the other. This plug will fit into the power outlet only one way. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician.
4. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit the product.
5. Do not overload wall outlets, extension cords, or integral convenience receptacles, as this can result in a risk of fire or electric shock.
6. Never push objects of any kind into this product through openings, as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
7. Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
8. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
9. Do not use attachments not recommended by the product manufacturer, as they may cause hazards.
10. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
11. Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating. Do not block or cover these openings.
12. Unplug the product during lightning storms or when unused for long periods of time.

Items in this package

Before discarding any packaging materials, please check thoroughly and ensure you have found the following items:

• Turntable
• 45 RPM adapter
• 3.5mm aux in cable
• Power adaptor

Please contact Crosley Customer Service if any accessory is missing from the package. Retain the original packaging materials for exchange or return purposes.

Specifications

Note: Design and specifications are subject to change without notice.

Note on Power Saving: To help save power consumption, some models comply with ERP energy saving standards. When there is no audio input for 20 minutes, the unit's power will automatically cut off. To resume playback, turn the power off and then on again.

Product Description

The Crosley CR8017A Voyager Turntable features a classic design with modern functionality. The illustration shows the top view of the turntable with various components labeled, and a side view showing the connection ports.

Labeled Components (Top View):

• 1. Turntable Platter
• 2. Turntable Spindle
• 3. Tonearm Lever
• 4. Hold Down Clip
• 5. Auto-stop Switch
• 6. Speed Switch
• 7. Tonearm
• 8. Function Switch
• 9. Pitch Control
• 10. On/Off-Volume Knob
• 11. Headphone Jack

Labeled Components (Rear/Side View):

• 12. Power Jack
• 13. RCA Jacks
• 14. Aux In Jack
• 15. 45 RPM Adapter (storage location shown)

Initial Setup

Essential Setup

1. Place the unit on a flat and level surface. The selected location should be stable and free from vibration.
2. Remove the tie-wrap that is holding the tonearm.
3. Connect the AC adaptor to the Power Jack of the unit.

Note: Do not plug the AC power adaptor into a power outlet before all assembly is completed. Before turning the power on, ensure all connection settings are correct. Always turn off the power when connecting or disconnecting.

Stereo System Connection

RCA Jacks

• The RCA Jacks output analog line-level signals and can be connected directly to a pair of active/powered speakers or the appropriate input of your stereo system.
• The Red plug connects with the Right channel, and the White plug connects with the Left channel.

Note: The RCA Jacks are not designed for direct connection to passive/unpowered speakers. If connected to passive speakers, the volume level will be very low.

Aux Input Connection

You can connect an audio device to this unit and play your music through its speakers. To do this, set the Function Knob to Bluetooth mode, connect the 3.5 mm auxiliary cable between your audio device and the Aux In Jack of this unit, and start playing the music.

Turntable Operation

1. Rotate the On/Off-Volume Knob to turn on the power.
2. Set the Function Switch to PHONO position.
3. Set the Speed Switch accordingly (33⅓, 45, or 78 RPM).
4. Place the record on the turntable. Use the 45 RPM Adapter if necessary.
5. Remove the stylus protector from the stylus assembly.

Note: To avoid stylus damage, ensure the included stylus guard is in place whenever the turntable is being moved or cleaned.

6. Release the tonearm from the Hold Down Clip.

Note: When the turntable is not in use, remember to lock the Hold Down Clip back.

7. Use the Tonearm Lever to lift up the tonearm.
8. Gently move the tonearm over the record where play is desired to begin. Set the Tonearm Lever back to the down position; the tonearm will descend slowly onto the record and begin playback.
9. When the record finishes playing, use the Tonearm Lever again to raise the tonearm and return it to the Tonearm Rest. Release the lever to allow the tonearm to rest. To suspend playback, repeat the same steps.
10. Lock the Hold Down Clip to secure the tonearm.

Platter Auto-stop

If the Auto-stop Switch is set to the ON position, the platter will stop spinning automatically when the record plays to the end. In rare cases, if the turntable stops playing before the end of the record, set the switch to the OFF position; this should resolve the issue.

Pitch Control

The turntable speed can be increased or decreased by approximately 10% by rotating the Pitch Control Knob. To increase the speed, turn the Pitch Control Knob clockwise. To decrease the speed, turn the knob counter-clockwise.

Needle Replacement

Removing Needle

1. Gently pull down the front edge of the needle.
2. Pull the needle forward.
3. Pull out and remove.

Diagram description: Three steps showing the needle being pulled forward and out of the cartridge.

Installing Needle

1. Position the needle with its tip facing down.
2. Line up the back of the needle with the cartridge.
3. Insert the needle with its front end at a downward angle and gently lift the front of the needle upward until it snaps into place.

Diagram description: Three steps showing the needle being inserted at an angle and then lifted up to snap into the cartridge. The final step is labeled "SNAP!".

Bluetooth Operation

1. Set the Function Switch to Bluetooth mode. You will hear an activation sound from the unit.
2. Turn on the Bluetooth feature of your audio device, search for "Crosley CR8017", and pair.
3. Once your device is successfully paired with the unit, you will hear a short confirmation sound.
4. Play and stream music from your device to the unit.

Note: Bluetooth version - 4.1

Turntable Maintenance

1. Do not touch the stylus tip with your fingers. Avoid bumping the stylus on the turntable mat or a record's edge.
2. Clean the stylus frequently with a soft brush, using a back-to-front motion only.
3. Clean records to remove dust or grease using a record cleaning brush and record cleaning solution.
4. Clean the turntable lid and cabinet with a slightly dampened microfiber cloth.

Note: Do not use cleansers containing alcohol, benzene, or other harsh chemicals, as they might damage the paint and finish of the turntable.

Crosley offers a product line of different cleaning accessories. Please ask your retailer or check the website www.crosleyradio.com for more cleaning product information.

Troubleshooting

There is no power

• Power adaptor is not connected correctly.
• No power at the power outlet.
• To help save power consumption, some models comply with ERP energy saving standards. When there is no audio input for 20 minutes, their powers will automatically cut off. To turn power back on and resume playing, turn the power off and then on again.

Power is on, but the platter does not turn

• Turntable's drive belt has slipped off.
• An aux in cable is plugged into the aux in jack; unplug it.

Turntable is spinning, but there is no sound, or sound not loud enough

• Stylus protector is still on.
• Tonearm is lifted up by the lever.
• Headphones are plugged in.

FCC Statements

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.