User Manual for JETI models including: MEZON-EVO Electronic Speed Controller for BLDC Motor, MEZON-EVO, Electronic Speed Controller for BLDC Motor, MEZON-EVO Electronic Speed Controller, Electronic Speed Controller, Speed Controller, Controller
Jeti Model Mezon Evo 70A Limited Motor Run ESC with 15A BEC | Buy ESCs at Modelflight
8 nov 2022 — QUICK SETUP. User manual. QUICK SETUP evo. Complete manual is available on www.jetimodel.com ... Controller`s setup is intuitive and together with JETI.
File Info : application/pdf, 12 Pages, 2.45MB
DocumentDocumentevo EN evo ELECTRONIC SPEED CONTROLLER FOR BLDC MOTOR EN User manual QUICK SETUP Complete manual is available on www.jetimodel.com Setup DC/DS evo EN evo 1 Introduction MEZON EVO is a series of controllers in aluminium case* with efficient cooling, full telemetry and advanced functions. Controller is designed for RC model planes, helicopters and other vehicles. Controller`s setup is intuitive and together with JETI Duplex transmitter very simple. Features: - full EX telemetry (voltage, current, capacity, revolution etc.) - setup of device through EX Bus communication from JETI Duplex transmitter - accurate governor and full support of helicopter models - F3A mode for acrobatic planes - adjustable brake with back energy recovering into accumulator - powerful BEC with adjustable output voltage - wide range of supply voltage 2 - 12 Lixx (max. 51V) - bidirectional motor run is possible 2 Overview Basic parameters of MEZON EVO controllers: Type Sustained current [A] Description MEZON Evo 40 BEC LMR* 40 (max 30s) Light weight controller,adjustable BEC MEZON Evo 70 BEC LMR* 70 (max 30s) Light weight controller,adjustable BEC MEZON Evo 50 BEC 50 Aluminium case, adjustable BEC MEZON Evo 80 BEC 80 Aluminium case, adjustable BEC MEZON Evo 85 OPTO 85 Aluminium case, optocoupler separation Listed currents are valid with sufficient air flow cooling * Light weight controllers LMR (Limited Motor Run) are not in aluminium case 1 evo 2.1 MEZON EVO BEC controllers Switch BEC Battery evo 80bec EN M Trottle channel BEC output Y1 EX Bus Ext. BEC output Pic.1 - standard connection between controller and receiver suitable for JETI Duplex transmitters users - black JR connector is connected into throttle channel output of receiver - red JR connector is connected into receiver output Ext., E1 or E2 If E1 or E2 receiver output is used then user has to manually configure E1 or E2 output to ,,EX Bus" functionality. REX receivers dispose of automatic communication detection and manual configuration is not necessary. For elderly Rx receivers configure "EX Bus" in menu ,,Model>Device Explorer>receiver>Serial link". - for sufficient power supply from BEC we strongly recommend connect both of JR connectors 2 evo EN If you don´t want to use BEC power supply, take out from JR connectors middle pins (red wired) and isolate correctly. Switching BEC technical data average current 15A max. current 30A (1s) max. temperature 100°C listed values are valid with sufficient air flow cooling 2.2 MEZON EVO OPTO controllers MEZON EVO OPTO controllers have input separation by optocoupler and BEC power supply is not available. For correct functionality it is necessary to supply receiver, servos and other electronic equipment with an external battery. Instead of a battery, it's also possible to use a separate power supply (JETI SBEC 30D EX for example, po-wered direct from main accumulator). evo 85opto Battery M Throttle channel Y1 Telemetry Ext. EX BUS Receiver battery RECEIVER BATTERY Nominal capacity: 3.1Ah Voltage: max. 8.2V Pic. 2 -standard connection between controller and receiver suitable for JETI Duplex transmitters users 3 evo EN 3 Configuration (setup) MEZON EVO controllers can be configured from JETI Duplex transmitters (described below), Jetibox or USB interface with JETI Studio application for PC (see *CM) There are two configuration possibilities: "Quick setup" - configuration through wizard (described below) "Expert setting" - full access for all controller possibilities (see *CM) Quick setup with predefined parameters for RC model type is normally sufficient for most users. Warning: during configuration motor run is blocked for safety reasons 3.1 Configuration procedure for planes, cars and boats models - choose model type, content of menus are automatically adapted for chosen model type Basic parameters: Start acceleration - motor start up time from zero revolution Response - speed reaction of running motor on throttle changing Timing - set up with information from motor producer Brake Soft/Medium/Hard - predefined brake profiles Manual - brake values defined by user Proportional - brake strength depend on throttle position 4 evo EN Number of cells Auto automatic detection of the number accu`s cells BEC voltage set BEC voltage for electronic equipment, range 5 - 8.4V Warning! The Automatic mode only works properly if you connect fully charged batteries to the controller. Warning! Damage risk of connected electronic equipment if incorrect BEC output voltage is configured. 3.2 Configuration procedure for F3A planes Choose model type, content of menus are automatically adapted for chosen model type. MEZON EVO controllers support special mode for F3A acrobatic planes ,,Menu>Model>Device explorer>MEZON EVO>Quick SetUp>F3A Plane". Brake strength depend on throttle position in this mode. This function provides activeplane speed stabilizing for downline figures. It`s similar as cruise control of car, but demanded speed depend on throttle position. Back nergy recovering into accumulator is automatically enable in this mode. Other possibilities - see chapter ,,Basic parameters". 5 evo EN 3.3 Configuration procedure for helicopters Choose model type, content of menus are automatically adapted for chosen model type. Number of motor poles set the number of motor poles regards motor producer information. Motor KV - set value of motor`s KV regards motor producer information. If both of above-mentioned parameters are unknown see *CM. Rotor Gear - set gear ratio between motor and helicopter`s rotor MAX rpm (gear out) - set revolution of helicopter`s rotor regards recommendation helicopter producer Autorotating mode - see *CM Governor setting - we recommend to keep ,,Auto", ,,Auto +0%". If automatic values are not suitable see *CM. Other possibilities - see chapter ,,Basic parameters". 6 evo EN 4 Telemetry MEZON EVO controllers integrates full telemetry with selectable recorded data set. All the selected data is saved and available for later analysis. Possible faults which occurred during operation are recorded in "Status" menu. This menu helps with faults solving and diagnoses. See *CM for detail items description. Menu telemetry ,,Min/Max" consists recorded minimum and maximum values of important parameters during controller operation. *CM - Complete Manual is available on: www.jetimodel.com 7 evo EN 5 Package contents - assembly Warranty and service This product is covered by warranty for 24 months after the day of purchase provided that it has been operated in accordance with these instructions at the specified voltage and is not mechanically damaged. When claiming warranty repairs for the product, always attach a proof of purchase. Warranty and post-warranty service is provided by your dealer or the manufacturer. Technical support In case you are not sure about the setup or some functions of the product contact our technical support. You can contact either your dealer, or directly the manufacturer JETI model s.r.o. For further information see our webpages www.jetimodel.com 8 evo EN Safety instructions - use quality power connectors designated for appropriate load current - keep power supply within the allowed voltage/cell range - set BEC voltage within servo producer instructions - ensure sufficient air flow cooling - isolate reliably all wires, conductors and connectors - reverse polarity causes damage to controller with loss of warranty - during controller configuration remove propeller or rotor blades - treat model with respect, after connection of power supply motor/model is live. Risk of injury! 9 evo EN ® Declaration of Conformity in accordance with the regulations of EU Directive EMC 2014/30/EU, RoHS 2011/65/EU and (EU) 2015/863 This declaration of conformity is issued under the sole responsibility of the manufacturer. Producer: JETI model s.r.o. Lomená 1530, 742 58 Píbor, Ceská republika IC 26825147 Declares, that the product Type designation: Model number: Country of origin: MEZON EVO 40 BEC LMR, 50 BEC, 70 BEC LMR, 80 BEC, 85 OPTO Czech republic The stated product complies with essential requirements of EMC 2014/30/EU, RoHS Directive 2011/65/EU and (EU) 2015/863. Harmonised standards applies: Protection requirements concerning electromagnetic compatibility [6] EN 61000-6-3:2007 + A1:2011 Electrical Safety and Health [3.1(a)] EN 62368-1:2015 RoHS EN 50581:2012 Píbor, 11.8.2022 Ing. Stanislav Jelen Managing Director 10 evo EN JETI model s.r.o. Lomená 1530, 742 58 Píbor Czech Republic - EU www.jetimodel.com info@jetimodel.cz