1. Your BS® Link Motor
Introduction
Thank you for choosing the Forest BS® Link motor. This guide provides essential information on how to operate, maintain, and maximize the performance of your Forest BS® Link motor. In this manual, you'll find step-by-step instructions for usage, charging (if you have chosen a battery-operated option), and troubleshooting, as well as tips to ensure safe and efficient operation.
General
Please read this manual and the safety instructions carefully before using this Forest product. Follow the instructions in this manual and keep it throughout the entire lifespan of the product. This manual describes the setup and operation of the BS® Link motor. Any use beyond the application scope defined by Forest is not permitted. Ignoring the instructions in this manual voids any liability and warranty from Forest Group.
Areas of Use
The BS® Link motor is designed for use with the Forest Roman Blind System.
Important Safety and Liability Information
To ensure safe and proper operation of the BS® Link motor, please follow the instructions in this document as well as the complete manual. Keep this document close to the product at all times or visit www.forestgroup.com to view it online. Use the product only as intended.
This product is not suitable for use in humid spaces such as bathrooms or outdoors. For the BS® Link motor to function correctly and safely, the complete Roman Blind System must be assembled with original & undamaged parts and devices of Forest Group (Nederland) B.V.
This product is not suitable for use by children; it is not a toy. Keep it (as well as the remote control) out of the reach of children at all times. Frequently examine the product for imbalance and signs of wear or damage.
Forest Group does not assume liability for resulting damages to persons, animals, and/or property, defects, labor on location, service calls, reinstallation, or expenses involved in shipping, packing, or returning goods, if the product has been abused/modified in any way or damaged by improper use or failure to observe these operating instructions. In such situations, the right to any form of warranty, service, and reimbursement of expenses shall cease.
Key safety points:
- This product is for indoor use only; do not use outdoors or in humid environments.
- Power supply: rechargeable lithium battery 12V.
- The motor will jog during setup; please do not proceed to the next step until the jog is complete.
- During setup, if no buttons are pressed for 10 seconds, the motor will exit the setting mode.
- The motor can be paired with a maximum of 10 controllers.
- Upper & Lower limits cannot be set at the same position; limits are saved even when power is off.
- The motor runs constantly for a maximum of 6 minutes without any other operation.
- Do not lift the motor by grabbing and pulling the power wire or the antenna.
2. Product Info
Product Details
Diagram Description: Shows a side view of the motor connected to a power line and module connection wire. Key components labeled are: Pairing Button, Power line, Module connection wire, Antenna.
Installation Overview
Diagram Description: Illustrates the motor mounted to a wall bracket, with a cord roll and the BS motor unit. Components labeled: Wall bracket, BS motor, Cord roll.
Power Options
- 12V Adapter: Art. no. (EU) 3636000004, (UK) 3636000005.
- External Battery 12V: Art. no. 36360000002.
3. Instructions
Control Functions
To operate the tubular motor, you need a Forest remote control with the Link protocol (EasyTouch line).
| Button EasyTouch | Description/Function |
|---|---|
| [Open] | Opens the curtains or blinds |
| [Close] | Closes the curtains or blinds |
| [Stop] | Stops the movement |
| [Channel +] | Switches to the next channel. The LED indicator moves to the right. |
| [Channel -] | Switches to the previous channel. The LED indicator moves to the left. |
| [Fav] | Allows users to quickly access their preferred curtain positions with a single press. |
| [Prg] | The Program button, enables users to access programming functions. |
Note: The [Prg] button is located inside the back of the remote control. The method to open the remote may vary depending on the model. Please refer to the specific instructions for your remote type.
4. Get Started
Tubular Motor Pairing Button Functions
| Functions | Pairing Button | Jogging Time | Note |
|---|---|---|---|
| OPEN/STOP/CLOSE | Short press | / | Can only be used when limits are already set. |
| Adding/Removing Controller | Hold for 2s | [Jog 1x] | Press the [Prg] button on the remote control within 10 seconds. |
| Deactivate RF control | Hold for 6s | [Jog 2x] | Hold Pairing button for 6s, motor jogs twice to show the motor RF control is deactivated. To activate again: hold Pairing button for 2s. |
| Direction Reverse | Hold for 10s | [Jog 3x] | All other settings remain the same. |
| Reset* | Hold for 16s | [Jog 4x] | Delete all settings. |
*Important: Be sure to reset the end positions before using the motor to prevent damage to both the fabric and the motor.
Pairing Motor with Forest EasyTouch Remote Control
1: Pairing procedure after assembly
Diagram Description: Sequence: Select channel on remote, remove power cover, press [Prg] within 10s, motor jogs once ([Jog 1x]), motor jogs twice ([Jog 2x]). Confirmed with OK.
2: Pairing procedure before assembly
Diagram Description: Sequence: Select channel on remote, remove power cover, press pairing button for 2s, motor jogs once ([Jog 1x]), press [Prg] within 10s, motor jogs twice ([Jog 2x]). Confirmed with OK.
3: Add a new remote using an existing remote (unassembled systems)
Diagram Description: Sequence: Press [Prg] on remote A, motor jogs once ([Jog 1x]). Press [Prg] on remote A again, motor jogs once ([Jog 1x]). Press [Stop] on remote B (to remove), motor jogs twice ([Jog 2x]). Confirmed with OK.
Note: Pairing cannot be done under group channel or 0 channel.
5. Settings
Direction Reverse
The blind moves in the right direction.
Diagram Description: Sequence: Press [Open], Roman goes up. Press [Close], Roman goes down.
If the limits are not set, and direction goes opposite:
Diagram Description: Sequence: Hold [Fav] + [Stop] for 2s, motor jogs once ([Jog 1x]). Direction reversed.
If limits are set and direction goes opposite:
Diagram Description: Sequence: Press [Prg], motor jogs once ([Jog 1x]). Press [Open] 1x, motor jogs once ([Jog 1x]). Press [Close] 1x, motor jogs once ([Jog 1x]). Direction reversed.
Note: Reverse the direction when it goes opposite.
Upper & Lower Limits Settings
Diagram Description: Sequence: Press [Open] or [Close] to move the blind. Fix upper point: Hold [Open] + [Fav] for 2s, motor jogs twice ([Jog 2x]). Upper limit set. Sequence: Press [Open] or [Close] to move the blind. Fix lower point: Hold [Close] + [Fav] for 2s, motor jogs twice ([Jog 2x]). Lower limit set.
Note: Upper & Lower limits cannot be set at the same point. As long as the end positions have not yet been set, the motor operates in step-by-step mode: The motor moves as long as you hold down the [Open] or [Close] button, and stops as soon as you release it.
Tip: If you hold the [Open] or [Close] button for 2 seconds, the curtain will continue to move in one continuous motion until you press [Stop].
Once the end positions have been set, the motor will automatically operate in one-touch mode. A single press of [Open] or [Close] will activate a continuous movement.
Cancelling Limits
Diagram Description: Sequence: Press [Prg], motor jogs once ([Jog 1x]). Press [Stop], motor jogs once ([Jog 1x]). Press [Prg], motor jogs once ([Jog 1x]). Limits cancelled.
Important: Make sure to reset the end positions before using the motor to prevent damage to both the fabric and the motor.
5. Settings (Continued)
Adjusting Upper & Lower Limits
Adjust Upper limit
Diagram Description: Sequence: Hold [Open] + [Fav] for 6s, motor jogs once ([Jog 1x]). Move blind with [Open] or [Close]. Fix new upper limit: Hold [Open] + [Fav] for 2s, motor jogs twice ([Jog 2x]). Confirmed with OK.
Adjust Lower limit
Diagram Description: Sequence: Hold [Close] + [Fav] for 6s, motor jogs once ([Jog 1x]). Move blind with [Open] or [Close]. Fix new lower limit: Hold [Close] + [Fav] for 2s, motor jogs twice ([Jog 2x]). Confirmed with OK.
Note: The operation should be done within 4 minutes.
Adjusting Motor Speed
Speed increase:
Diagram Description: Sequence: Press [Prg], motor jogs once ([Jog 1x]). Press [Stop], motor jogs once ([Jog 1x]). Press [Open], motor jogs once ([Jog 1x]).
Speed decrease:
Diagram Description: Sequence: Press [Prg], motor jogs once ([Jog 1x]). Press [Stop], motor jogs once ([Jog 1x]). Press [Close], motor jogs once ([Jog 1x]).
Note: If the motor doesn't jog, the max/min speed has already been reached. There are 3 speeds adjustable.
Setting Up the Favourite Function
The Favourite Function allows you to set a preferred position that can be activated with a single press of a button.
Setting the Favourite Function
Diagram Description: Sequence: Move blind with [Open] or [Close]. Fix Fav. position: Hold [Fav] + [Stop] for 2s, motor jogs twice ([Jog 2x]). Fav. position set.
Important: The Favourite function can only be set if the end positions are configured.
Cancelling Favourite Function
Diagram Description: Sequence: Blind is at Fav. position. Hold [Fav] + [Stop] for 2s, motor jogs once ([Jog 1x]). Fav. position Cancelled.
5. Settings (Continued)
Switching Between Constant Touch Mode and One-Touch Mode
Once the end positions are set, the motor operates in one-touch mode (the curtain moves in a continuous motion). To switch to step-by-step mode, follow these steps:
Diagram Description: Sequence: Press [Prg], motor jogs once ([Jog 1x]). Press [Stop], motor jogs once ([Jog 1x]). Press [Stop], motor jogs once ([Jog 1x]). The setting has been changed.
The same operation can toggle from step-by-step mode to one-touch mode.
Note: When the motor is in step-by-step mode, it is also possible to fully open or close the curtain in one smooth motion by holding the [Open] or [Close] button for more than 2 seconds.
Unpair Remote Controls
Unpair a single remote control
Diagram Description: Sequence: Press Pairing Button for 2s, motor jogs once ([Jog 1x]). Press [Prg], motor jogs once ([Jog 1x]). Confirmed with OK.
Unpair remote control B via pre-existing remote control A
Diagram Description: Sequence: Press [Prg] on existing remote A, motor jogs once ([Jog 1x]). Press [Prg] on existing remote A again, motor jogs once ([Jog 1x]). Press [Stop] on remote B (to remove), motor jogs twice ([Jog 2x]). Remote control B unpaired.
Unpair all remote controls
Diagram Description: Sequence: Press [Prg], motor jogs once ([Jog 1x]). Press [Prg], motor jogs once ([Jog 1x]). Press [Close], motor jogs once ([Jog 1x]). All remote controls unpaired.
Note: All other settings, except paired remote controls, remain the same.
6. Installation & Connecting Bluetooth Module
Module Specifications:
- Working voltage: 3V~3.6V
- Supporting protocol: 802.11B/G/N20
- Working Temperature: 0 - 40 °C
- For Indoor Use only
Download App
a. Search "Forest Connect" in the app store or scan the QR-Code. [QR Code for Forest Connect App - excluded as per instructions].
b. Complete account registration and login to the app.
Install Bluetooth Module for App Control
a. Power on, insert Bluetooth module to motor module connection wire.
b. Wait for 10s to see if the indicator is blinking.
c. If indicator didn't blink, please try:
Method 1: Long press the RESET button until the indicator blinks. The motor is ready for Bluetooth connection. (A paperclip or similar tool may be used instead of a pin).
Method 2: Short press [Prg] on the back of the controller, motor jogs once ([Jog 1x]); short press [Close] 1x, motor jogs once ([Jog 1x]); then short press [Open] 1x, motor jogs once ([Jog 1x]). The blue indicator blinks, which means the motor enters Bluetooth connection status.
Diagram Description: Shows the motor in Bluetooth connection status with a blinking blue indicator.
d. Find the added Bluetooth gateway on the "Forest Connect app". Click “+” to add a subdevice, and then click "LED already blink". The APP will automatically search for the motor device.
e. After adding successfully, click to modify the device name.
f. The Bluetooth module indicator is always on after successful network connection.
g. Enter the main interface to control the operation of the BS Link tubular motor.
7. Notice
Recycling
Do not dispose of the product with household waste. Ensure that you return it to a collection point or depot for recycling purposes. [Recycling symbol ♻️]
8. Support & Technical Specification
FAQ
Why isn't the motor working?
- Check if you have paired a remote control. If your remote is not paired yet, you need to pair the remote control with the motor by following the pairing instructions in this manual.
- Check if the motor is active. If the motor is inactive, you can reactivate it by pressing the pairing button twice (poke the button 2 times) to activate the motor.
Why does the motor stop suddenly during operation?
- Check if the upper and lower limits are set correctly. If not, re-set the upper and lower limits according to the instructions in this manual.
- Check if the tubular motor doesn't exceed the rated load. In that case, reduce the load on the motor by adjusting the fabric and checking whether it falls within the specified weight limits.
Why does the motor only move in one direction?
- Check if the motor's limits are set correctly. If they are incorrect, then cancel the original limits and set new upper and lower limits following the instructions in this manual.
Technical Specification
| Voltage | 12Vdc |
| Power max. | 9.6W |
| Current max. | 0.8A |
| Torque | 0.8Nm |
| Speed | 20/30/40 |
| Run time max. | 6 minutes |
| Length | 20.8cm |
| Diameter | 24mm |
| Frequency | 433.92MHz |
| RF range (max.) | 30m |
| Protection degree | IP20 |
| Temperature | 0-40°C |
| Weight load fabric | 4 kg |
| Battery charging time | 6-8 hours (blue light on = fully charged) |
The images in this document are not binding.
For the digital manual, scan the QR code or visit: www.forestgroup.com/en/downloads/technical-documents
