Upholstered Bed Frame Assembly Instructions - Full/Queen Size
Parts List
| Part # | Description | Quantity |
|---|---|---|
| 1 | Headboard (KOPFTEIL) | 1 PC |
| 2 | Footboard (TRITTBRETT) | 1 PCS |
| 3 | Leg (BEIN) | 2 PCS |
| 4 | Side Rail (SEITENGITTER) | 1 PC |
| 5 | Side Rail (SEITENGITTER) | 1 PC |
| 6 | Side Rail (SEITENGITTER) | 1 PC |
| 7 | Side Rail (SEITENGITTER) | 1 PC |
| 8 | Crossband (CROSSBAND) | 1 PC |
| 9 | Support Rail (SUPPORT RALL) | 2 PCS |
| 10 | Support Rail (SUPPORT RALL) | 5 PCS |
| 11 | Leg (BEIN) | 2 PCS |
| 12 | Leg (BEIN) | 1 PC |
| 13 | Leg (BEIN) | 4 PCS |
| 14 | Leg (BEIN) | 10 PCS |
| 15 | Side Rail Support | 2 PCS |
| 16 | Side Rail Support | 2 PCS |
| 17 | Slats (SLAT) | 2 SET |
| 18 | LED Light Strip | 1 PC |
| 19 | Remote Control | 1 PC |
| 20 | Power Adapter (Netzadapte) | 1 PC |
| 21 | Two-in-One Cable (Zwei-in-Eins-Kabel) | 1 PC |
| 22 | Light Strip Controller | 1 PC |
Hardware List
| Label | Description | Quantity |
|---|---|---|
| A | Ø5/16"x55mm | 12+1PCS |
| B | Ø5/16"x40mm | 7PCS |
| C | Ø5/16"x25mm | 28+1PCS |
| D | Ø1/4"x15mm | 8+1PCS |
| E | Ø1/4"x38mm | 12+1PCS |
| F | Ø5/16"x19mm | 47+2PCS |
| G | Ø1/4"x16mm | 20+2PCS |
| H | Ø5/16" | 47+2PCS |
| I | Ø5/16" | 8+1PCS |
| J | M4x15mm | 2PCS |
| K | Ø5/16" (Tool) | 1PC |
| L | Ø1/4" (Tool) | 1PC |
| M | Ø5/16" (Tool) | 1PC |
Assembly Instructions
Step 1: Attach Headboard to Side Rails
Connect the Headboard (1) to the two Leg assemblies (3, labeled R and L). Use four of hardware A (Ø5/16"x55mm), four of hardware H (Ø5/16"), four of hardware F (Ø5/16"x19mm), and one tool K (Ø5/16").
Step 2: Attach Footboard to Side Rails
Connect the Footboard (2) to the Leg assemblies (3, labeled R and L). Use four of hardware C (Ø5/16"x25mm), four of hardware H (Ø5/16"), four of hardware F (Ø5/16"x19mm), and one tool K (Ø5/16").
Step 3: Connect Side Rail Supports (First Pair)
Attach two Side Rail Supports (15) to the Side Rails (4 and 6). Use six of hardware E (Ø1/4"x38mm), six of hardware G (Ø1/4"x16mm), and one tool L (Ø1/4").
Step 4: Attach Side Rail Supports (Second Pair)
Attach two Side Rail Supports (15) to the Side Rails (4 and 6). Use four of hardware D (Ø1/4"x15mm), four of hardware G (Ø1/4"x16mm), and one tool L (Ø1/4").
Step 5: Connect Side Rail Supports (Third Pair)
Attach two Side Rail Supports (16) to the Side Rails (5 and 7). Use six of hardware E (Ø1/4"x38mm), six of hardware G (Ø1/4"x16mm), and one tool L (Ø1/4").
Step 6: Attach Side Rail Supports (Fourth Pair)
Attach two Side Rail Supports (16) to the Side Rails (5 and 7). Use four of hardware D (Ø1/4"x15mm), four of hardware G (Ø1/4"x16mm), and one tool L (Ø1/4").
Step 7: Attach Legs to Support Rails
Connect the Legs (13) to the Support Rails (9). Use six of hardware B (Ø5/16"x40mm), six of hardware H (Ø5/16"), six of hardware F (Ø5/16"x19mm), and one tool K (Ø5/16").
Step 8: Connect Headboard Assembly to Frame
Attach the assembled Headboard section (from Step 1) to the main bed frame. Use four of hardware C (Ø5/16"x25mm), four of hardware H (Ø5/16"), four of hardware F (Ø5/16"x19mm), and one tool K (Ø5/16"). Also, attach the Footboard (2) to the frame using similar hardware.
Step 9: Secure Main Frame Structure
Secure the main bed frame structure. Use eight of hardware C (Ø5/16"x25mm), eight of hardware H (Ø5/16"), eight of hardware F (Ø5/16"x19mm), and one tool K (Ø5/16").
Step 10: Attach Remaining Legs and Support Rails
Attach the remaining Legs (13) and Support Rails (9) to the frame. Use eight of hardware A (Ø5/16"x55mm), eight of hardware H (Ø5/16"), eight of hardware F (Ø5/16"x19mm), eight of hardware I (Ø5/16"), and one tool M (Ø5/16").
Step 11: Install Central Support Rails
Connect the central support rails (10, 12, 14) to the bed frame. Use one of hardware B (Ø5/16"x40mm), twelve of hardware C (Ø5/16"x25mm), thirteen of hardware H (Ø5/16"), thirteen of hardware F (Ø5/16"x19mm), and one tool K (Ø5/16").
Step 12: Place Slats
Lay the Slats (17) across the installed support rails to form the mattress base.
Step 13: Install LED Light Strip
Attach the LED Light Strip (18) to the designated area on the bed frame.
Step 14: Connect LED Components
Connect the Light Strip Controller (22) to the LED strip. Connect the Two-in-One Cable (21) to the controller. Connect the Power Adapter (20) to the cable. The Remote Control (19) can now be used to operate the lights.