User Guide for MOTIONBLINDS models including: MOTOR CM-03-E, Roller Blind
WARNING. Read the instructions carefully before assembling and using the product. Assembly can be completed by non-professionals. For indoor use only. Young children.. View
Install the blind Activate the blind 1 2 Follow the steps in the installation instructions to install the blind. To activate the blind, connect it to a standard USB-C 5V power supply via a USB-C cable.
Support | evehome.com
File Info : application/pdf, 12 Pages, 1.60MB
DocumentDocumentMOTIONBLINDS MANUAL setup guide EN ROLLER BLIND MOTOR CM-03-E WARNING Read the instructions carefully before assembling and using the product. Assembly can be completed by non-professionals. For indoor use only. Young children can strangle themselves with the loop of pull cords, chains and tapes, and cords that operate window coverings. To avoid strangulation and entanglement, keep cords out of reach of young children. 2 Cords may ensnare a child's neck. Move beds, cots and furniture away from window covering cords. Do not tie cords together. Make sure cords do not twist together and form a loop. Cleaning Follow these general rules when cleaning the outside of the device and its components: Use a damp, soft, lint-free cloth. Avoid getting moisture in openings. Do not use aerosol sprays, solvents, alcohol, or abrasives. Service & Support Do not perform repairs yourself. Do not attempt to open the device or disassemble it. You run the risk of electric shock and voiding the limited warranty. No user-serviceable parts are inside. Warranty Service First follow the advice in this manual. If the product appears to be damaged or does not function properly, go to your local dealer for instructions on how to obtain warranty service. Recycle This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collec-tion systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling. Conforms to UL Std. 325 Certified to CSA Std. C22.2#247 Buttons and functions USB-C charging port LED (Battery/Reset indicator) End position button Reset/Program button Pull control 3 1 Install the blind Follow the steps in the installation instructions to install the blind. Bracket Motorized 4 x Outside mount 2 x 2 x Inside mount 2 x BOutside mount 4 Deduwctid1th1/fo4rinsccrhefwropmosoitpioennisng Inside mount Max. 1/8 " 2 Activate the blind To activate the blind, connect it to a standard USB-C 5V power supply via a USB-C cable. This can be your iPhone's power adapter, for example. 3 Download the Eve app Download the Eve app from the App Store. 5 4 Setup the blind Open the Eve app and tap Add Accessory. Eve will now guide you through the setup process. If you have previously set up an accessory, go to Settings and tap Add Accessory. The end positions of the blind, top and bottom, are pre-programmed. These can be adjusted by following the steps in the app. 5 Hide the HomeKit Setup Code Slide the tassel up and rotate a quarter turn to hide the HomeKit Setup Code into the tassel. 6 Recharge the blind To charge the blind, connect it to a standard USB-C 5V power supply via a USB-C cable. This can be your iPhone's power adapter, for example. LED light flashes red during operation; Charge the battery LED light flashes green; battery is charging LED light constantly green; battery is fully charged 7 Important Safety instructions WARNING: To reduce the risk of severe injury or death, it is important to follow these instructions for personal safety. Save these instructions. Important Installation instructions WARNING: Important safety instructions. Follow all instructions, since incorrect installation can lead to severe injury. Read and follow all installation instructions. This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children should not play with the appliance. Cleaning and user maintenance should not be performed by children without supervision. Do not allow children to play with fixed controls. Keep remote controls away from children. Frequently examine the installation for imbalance and signs of wear or damage to cables and springs. Do not use if repair or adjustment is necessary. This instruction manual is also available on the website. The drive must be disconnected from its power 8 source during cleaning, maintenance and when replacing parts. The A-weighted emission sound pressure level of the drive is equal to or less than 70dB(A). Indoor and household use only. Disconnect the drive from the power supply or switch off the automatic controls when maintenance, such as window cleaning, is being carried out in the vicinity. When operating a biased switch, make sure that other persons are kept away. Do not operate when maintenance, such as window cleaning, is being carried out in the vicinity. The tube motor must only be supplied with safety extra low voltage corresponding to the marking on the appliance. This motor can only be used with soft material for driven parts. Hazardous unprotected moving parts of the drive must be installed higher than 2.5m above the floor or any other level surface that could provide access to it. Install the actuating member of a manual release at a height less than 1.8m. The actuating member of a biased switch is to be located within direct sight of the driven part but away from moving parts. It is to be installed at a minimum height of 1.5m and not accessible to the public. The mass and the dimension of the driven part must be compatible with the rated torque and rated operating time. Fixed controls have to be clearly visible after installation. The driven part must be compatible with the rated torque 1.1 N.m and rated operating time (12 min). Minimum tube diameter: Ø25mm. The drive is intended to be installed at a height of at least 2.5m above the floor or any other accessible level surface. All-pole disconnection switches must be incorporated in the fixed wiring in accordance with the wiring rules. The appliance must only be supplied at safety extra low voltage corresponding to the marking on the appliance. Before installing the drive, remove any unnecessary cords or components and disable any equipment not needed for powered operation. FCC Manual | FCC ID: ZY4CM03E Reorient or relocate the receiving antenna Regulatory Information Increase the distance separating the equipment and receiver 1 FCC Information for User Connect the equipment to an outlet on a circuit This product does not contain any user different from that to which the receiver is serviceable components and is to be used with connected approved antennas only. Any product changes Consult the dealer or an experienced radio/TV or modifications will invalidate all applicable technician for help regulatory certifications and approvals. EU Declaration 2 FCC Electronic Emission Notices Hereby, Coulisse declares that the radio This device complies with part 15 of the FCC Rules. equipment type CM-03-E is in compliance Operation is subject to the following two whith directive 2014/53/EU. The full text of the conditions: EU declaration of conformity is available at the 1. This device may not cause harmful interference following internet address: www.my.coulisse.com 2. This device must accept any interference received, including interference that may cause Frequency range: 433 MHz, RF power: 2.32 dBm undesired operation. Frequency range BLE: 2402 - 2480 MHz, RF power: 3 dBm EIRP 3 FCC Radio Frequency Interference Frequency range Thread: 2405 - 2480 MHz, statement RF power: < 20 dBm EIRP This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment 9 is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area may cause harmful interference, in which case the user will be required to correct the interference at their own expense. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reset the connection Hold the program button for 10 seconds to delete the connection between the blind and the app. The LED lights up 5 times and the blind steps up and down 1 time to indicate that the connection is reset. Now the blind can be reconnected. 5 x 10 s 10 Reset the blind Resetting the blind results in deleting the end positions and connections of the blind with apps and remote controls. Shortly press the program button to activate program mode. The blind will start stepping up and down.Hold the reset/program button for at least 20 seconds to reset the blind. The blind will stop stepping twice. After the second stop, the blind will give one extra step to indicate that is has been reset. Short press 5 x 20 s + More information Please scan the QR code below to view the complete user manual with more information and advanced options. MOTIONBLINDS MANUAL USER MANUAL ROLLER BLIND MOTOR CM-03-E User Manual rtube.nl/red1618 11 Coulisse B.V. Vonderweg 48, 7468 DC Enter, The Netherlands room: notes: motionblinds.com/eve CM03E-SE-U-R2Adobe PDF Library 15.0 Adobe InDesign 16.0 (Windows)