8 Cube Storage Unit

Dimensions

• Width: 61.2cm
• Depth: 29.5cm
• Height: 120.8cm

MADE IN GREAT BRITAIN

Important - Please read these instructions fully before starting assembly.

If you need help or have damaged or missing parts, call the Customer Helpline: 08450613967

Please turn to the back page for important information when contacting the Customer Helpline.

Safety and Care Advice

Important - Please read these instructions fully before starting assembly.

• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area; small parts could choke if swallowed.
• Make sure you have enough space to lay out the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft, level surface to avoid damaging the unit or your floor.
• Parts of the assembly will be easier with 2 people.
• We do not recommend the use of power drill/drivers for inserting screws, as this could damage the unit. Only use hand screwdrivers.
• Do Not dispose of packaging until assembly is complete.
• Dispose of all packaging carefully and responsibly when assembly is complete.

Care and maintenance

• To protect the furniture, position the furniture out of direct sunlight and away from direct heat sources such as radiators and fires.
• Do not place the furniture in excessively dry and humid conditions.
• From time to time, check that there are no loose screws on this unit.
• Always lift furniture when moving it (do not drag) otherwise the joints may be damaged.
• Do not place hot or cold objects on the surface; always use protective mats to avoid marking the furniture.
• This product should not be discarded with household waste. Take it to your local authority waste disposal centre.
• Clean spills up immediately.
• Dust surfaces with a soft, dry, lint-free cloth.
• More stubborn marks can be removed using a damp (not wet) cloth. Wipe the surface dry immediately using a soft, lint-free cloth.
• Do not use detergents, abrasive cleaning products, or cleaning products that contain ammonia, solvents, or silicone, as these may damage the surface finish.

Components - Panels

Please check you have all the panels listed below.

Important - Thick lines indicate finished edges.

• 9096 Top/Bottom x2 (58.0x29.3cm)
• 9121 End Panel x2 (120.8 x 29.5cm)
• 9101 Back Panel x4 (30.8x29.5cm)
• 9097 Shelf x3 (58.0x29.3cm)
• 9098 Divider x4 (28.2x29.1cm)

Components - Fittings

If you have damaged or missing components, call the Customer Helpline: 0845 0613967. Please turn to the back page for important information when contacting the Customer Helpline.

Please check you have all the fittings listed below.

Note: The quantities below are the correct amount to complete the assembly. In some cases, more fittings may be supplied than are required.

• A 45mm screw x 10 (Code 690001075)
• B Dowel 30mm x 16 (Code 770001006)
• C Dowel 50mm x 6 (Code 770003550)
• D L bracket x 1 (Code 760001901)
• E 12mm screw x 2 (Code 690001099)
• F Panel pin x 32 (Code 760001012)
• G Panel Pin Locator (Code 684004501)
• H Cover cap x 10

Tools required

• Large Cross Headed Screwdriver
• Small Hammer
• Eye protection (when using a hammer)
• Tape Measure

Ruler - Use this ruler to help correctly identify the screws

0 mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Exploded View

The exploded view shows the components and their placement during assembly. Panel numbers are indicated.

Assembly Instructions

Step 1: Fitting dowels to the divider panels.

1. Insert 2 of the 30mm dowels (B) into the pre-drilled holes in one end of the divider panel (9098) and 2 50mm dowels (C) into the other end of the same panel.
2. Insert 2 of the 50mm dowels (C) into only one end of 2 of the divider panels (9098).
3. Insert 2 of the 30mm dowels (B) into only one end of the other divider panel (9098).

Step 2: Fitting dowels to the shelf panels.

1. Insert 2 of the 30mm dowels (B) into the pre-drilled holes in both ends of the shelf panels (9097).

Step 3: Connect shelf panel and divider panels.

1. Locate the divider panel (9098) which has the 2 50mm dowels (C) inserted into the pre-drilled holes in panel (9097).
2. Slide the 50mm dowels (C) through the pre-drilled holes in the shelf panel (9097) and connect to the next divider panel (9098).

FINISHED EDGES TO THE FLOOR

Step 4: Connect the divider to the shelf and the next divider.

Slide the dowels (already inserted) in the divider panel (9098) through the shelf panel (9097) and into the next divider panel (9098).

Step 5: Connect the bottom divider to the shelf and the remaining divider.

Slide the dowels (already inserted) in the divider panel (9098) through the shelf panel (9097) and into the next divider panel (9098).

Step 6: Connect top/bottom panels to the dividers panels.

Insert the dowels (already inserted into the divider panels) (9098) into the pre-drilled holes in the top & bottom panels (9096).

Step 7: Fasten one of the end panels to the shelves and top/bottom panels.

Connect the end panel (9121) to the dowels in the shelf panels (9097).

Secure the end panel (9121) in place by using screws (A) and screwing into the pre-drilled holes in the top & bottom panels (9096) and the central shelf (9097).

Step 8: Fasten the other end panel to the shelf and top & bottom panels.

Connect the end panel (9121) to the dowels in the shelf panels (9097).

Secure the end panel (9121) in place by using screws (A) and screwing into the pre-drilled holes in the top/bottom panels (9096) and the central shelf (9097).

Step 9: Squaring the unit up.

Important. Ensure a tape measure is used to square unit up!

Before securing the back, it is necessary to square up the unit.

You can do this by measuring between XX - XX and YY - YY, ensuring these are the same (DIAG 1).

If they are not (DIAG 2), apply slight pressure as indicated (DIAG 3) until they are the same.

DIAG 1: [Check measurement]

DIAG 2: [Measurement incorrect]

DIAG 3: [Apply pressure]

Step 10: Attach the 4 back panels.

Ensure that you measure the back panel and attach the longest side as shown.

Use the panel pin guide (G) when locating the panel pins (F). This will hold the panel pins vertically.

Ensure that the distance from the edge of the back panels to the edge of the top / bottom / shelf and end panels is equal on every back panel.

Stand the unit upright once this is complete.

Step 11: Fixing to wall

We recommend that this unit is fixed to a suitable wall to prevent possible overbalancing. We have included a fixing bracket (D) for this. No fixing screws are provided as they will need to suit the wall type, and the length of screw will depend on the distance from the back of the unit to the wall. 2 screws (E) are provided to attach the bracket to the unit.

Please ensure fixings used are appropriate to your wall type. Locate the bracket to the top panel or to the end panel as close to the top as possible. We do not specify exact location for the bracket; this is left to the customer's discretion.

Warning: Please take care when drilling into the wall, avoiding any pipes and wires. Wear safety goggles when drilling. The use of a residual current device (RCD) is recommended when working with tools. If in doubt, consult a qualified person.

Step 12: Use the cover caps to conceal exposed fittings.

Using the 10 cover caps (H) provided, conceal the exposed screws by placing these caps over them.

Congratulations! Your unit is complete.

Important Information

If you need help or have damaged or missing parts, call the Customer Helpline:

0845 061 3967

8am - 4.30pm (Monday to Thursday)
8am - 2.30pm (Fridays)

(by contacting the customer service line, your statutory rights are not affected)

Please have the following information to hand:

• Unit Description
• Product Code
• Product Colour
• Place of Purchase
• Catalogue Ref. No.
• Item Code
• Assembly Instructions

We have an answer machine should you contact us out of office hours, so in addition to the above information, could you leave your name, address, daytime telephone number, and the nature of your call on the answerphone. All calls will be actioned asap.

You can also e-mail your requests to us at: customer.helpdesk@addspacefl.co.uk

Alternatively, you can write to us at: Customer Service Department, Addspace Furniture Limited, Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, South Yorkshire, S66 8QY.