User Manual for Shenzhen Maimiao Innovation Technology models including: MX5, 2AWK9-MX5, 2AWK9MX5, MX5 Smart Security Light Camera, MX5, Smart Security Light Camera
Shenzhen Maimiao Innovation Technology Co., Ltd. MX5 Smart Security Light Camera 2AWK9-MX5 2AWK9MX5 mx5
Smart Security Light Camera Maimiao TM MX5 Top Light Top Lock Screw Installation Steps User Manual Main Light Wall Mouting Plate Key Features Power wire via Hole 1080P Full HD Security Camera 1200 Lumen White LED Lamp APP View Live Video & Playback PIR & Sensor Dual Detection Two Way Audio APP Push Notifications APP Control Light & Adjust Brightness Waterproof Camera Lens Bottom Lock Screw Hole Speaker PIR Reset Button Indicator MIC Micro SD Spare Parts List X8 X2 X1 X1 1.Fix the Wall Mouting Plate > Connect the power cable >Mount the Camera housing > Power it up 2.Download and install "TuYa Smart" app >Open app >Registered account 3. Click Add Device > select Security & Sensors > Smart Camera > click Other Mode(upper right) > select Mode > click next step X2 Bracket (Option) Cover Pad (Option) 1 NOTE: This product only supports QR code & Smart Mode & Wired Network(Option,Only for Ethernet Version) Product as AP mode are not supported; Please refer to the following APP Installation And Initial Configuation Product Installation Instruction 1.Hold the side of Wall Mouting Plate by hand, slightly rock up and down, then pull out the Wall Mouting Plate A A D C A.Screw hole B.Square outlet fixing screw hole C.Rectangleoutlet fixing B B screw hole D.Round bracket nut fixing C D LAN G hole E A F A E.Green Power socket G.LAN Socket(Option) Top Lock Screw Bottom Lock Screw Hole M4 Screw M4 Screw Cover Pad 2.First made the power cable via to the F hole> connect the cable to green power socket (E position)> use screwdriver to fix the cable tight>according to the installation environment>select one installation mode (A to D) to fix the Wall 3. Align the Housing back Rectangle gap with the Wall Mouting Plate > press the Housing close to the Plate >lock the up & bottom lock screws to For Circular Outlet (option): as shown in the figure above first lock two long M4 screws on the circular bracket. Mouting Plate on the wall. complete the installation. >use 2 short M4 screws to fix the bracket on the outlet. A. (For no Outlet):Mark 4 A position points with a pen>Drill holes above marked points>Tap in 4 plastic plugs> Lock 4 screws to fix the Wall Mouting Plate on the wall. B. (For Square Outlet):Use 2 M4 screw to aim the outlet screw hole >lock the screw to fix the Wall Mouting Plate and square Outlet . Recommend installation height is 2.5M: Distance from the ground to the bottom of the product. > place Cover Pad between bracket and plate >insert two screws into the screw holes of the plate. >lock two spare nuts at D position to fix the plate C. (For Rectangle Outlet):Use 2 M4 screw to aim then outlet screw hole> lock the screw to fix the Wall Mouting Plate and Rectangle Outlet . & circular bracket. D.(For Circular Outlet): First lock 2 long M4 screws on the circular bracket >use two short M4 screws fix the circular bracket to outlet>place the Cover Pad on the bracket >Insert 2 bracket screws after aligning the Plate holes > lock the nut to finish Wall Mouting Plate fixed to the circular bracket. 2 APP Installation And Initial Configuation 1.Preparation After power on 1 minute > check the device is waiting for installation (red Indicator light is flashing ),if not please reset the device(Press and hold the reset button for 5 seconds then release) >Cell phone connected to the same WiFi router >Check the WiFi signal strength displayed by the cell phone at the place where the device is installed is no less than 2 bars. 2.Use APP store to search "Tuya Smart" >download and install>open Tuya Smart app>Registered Account QR code Mode 3. Open APP main page > click Add device > Select Security & Sensors > Smart Camera > Other Mode (upper right) to select Mode QR code mode:Focus the Cell Phone Screen's QR code on the Lens(the distance is about 20 cm)>after the QR code is identified,the device will make beep sound>Click I Heard a Prompt>Waiting for Conneting device(about 1 minute)>click Done. Smart mode: Input WiFi password>next step>waiting for Conneting device(about 1 minute)>click Done. Wired Network(option): First insert network cable to the Lan Socket >observe that the green and yellow indicator lights are flashing>click next step>click found device>(about 1 minute)>click Done.(only for support ethernet device AP Mode :(not supported) 3 Operation Status Description 1.Red indicator : blinks means searching network. Blue indicator: blinks means network connection is successful. meanwhile searching the server. Always lights means device online. Yellow indicator: blinks means Ethernet active. Green indicator: blinks means Ethernet access successful. 2. Reset to factory setting: After powered on 1 minute , press and hold the reset button for more than 5 seconds then release, and hear the voice"reset complete" means reset to factory setting successful. Main Parameter Product Name Model Number Camera Resolution Viewing angle Operational Temperature WIFI Power Supply Power Weight Dimensions(H x W x D) Smart Security Light Camera MX5 1920*18001080P) 110° -20 to +50 IEEE 802.11b/g/n 100-240VAC ,50/60HZ,0.2A 25W(MAX) 980g 300mmx111mmx112mm Common Fault List Fault type Indicator Status Solution No Power Indicator off Boot Failed Red & Blue LED always lights Check the power connection status Power off 5 seconds, then power on again Connect to W iFi Failed Red LED always blinks Check the W iFi signal strength near the installation of the device through the mobile phone (it needs to be greater than or equal to 2), check whether the W iFi password is correct, if the password is not correct, please click return, reenter password. Connect to Server Failed Blue LED always blinks Check whether the network is connected to the Internet normally 4 NOTE This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Changes or modifications not expressly approved by the party responsible for compliancecould void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:-- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver.-- Connect the equipment into an outlet on a circuit differentfrom that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC's RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna. Changes or odifications made to this equipment not expressly approved by manufacturer name) may void the FCC authorization to operate this equipment. FCC ID:2AWK9-MX5 5 Contact us Manufacturer: Shenzhen Maimiao Innovation Technology Co., Ltd Address: 1F No. 116, Long shi Road, Xin lian Community, Long gang District, Shenzhen ,China Tel: +86075528998667 Email: faq@syshare.comCorel PDF Engine Version 18.0.0.448