User Manual for Uhlmann Zacher models including: CX2176 Electronic Double Knob Cylinder, CX2176, Electronic Double Knob Cylinder, Double Knob Cylinder, Knob Cylinder
Uhlmann & Zacher GmbH EDH420 2APV6-EDH420 2APV6EDH420 edh420
User Manual CX2176/CX6176/CX8176 Prepare door 23/4" (70mm) Assemble the square pin A 11/16" (17.5mm) for Door Thickness 13/8" 7/8" (22mm) for Door Thickness 13/4" 23/4" (70mm) or 23/8" (60mm) Insert the square onto the retaining pin and into the square holder. B Insert the spiral clamping pin into the square. All contents current at time of publication. 117C V1.0 07/23/2021 User Manual CX2176/CX6176/CX8176 Installation A Slide mortise lock into edge bore of the door. Check that the faceplate does not project outside door, but it should also not be installed sunk. Use washers(s) to adjust penetration depth of the mortise lock. Fix lock by screwing it to the door. B 2 1 C 1 Insert the square pin of the electronic door handle into the square nut of the lock. 2 Insert the holder of the mechanical door handle from the other side and screw it along with the electronic door handle through the door panel. Use the supplied mounting screws. Insert the mechanical door handle keeping it in a horizontal position. For door handles pointing to the left, tighten the rosette towards the right, guide it over the handle holder and engage the bayonet lock. Accordingly, tighten the rosette towards the left for door handles pointing to the right. D Insert the locking screw from the bottom of the mechanical door handle and tighten it. All contents current at time of publication. 117C V1.0 07/23/2021 User Manual CX2176/CX6176/CX8176 FCC Compliance Statement This device (EDH420 FCC ID : 2APV6-EDH420) complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The Federal Communications Commission (FCC) warns the users that changes or modifications to the unit not expressly approved by the party responsible for compliance could void the user´s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Canadian Compliance Statement This device (EDH420 IC : 24382-EDH420) complies with Industry Canada´s license-exempt RSSs. Operation is subject to the following two conditions 1. This device may not cause interference; and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil (EDH420 IC : 24382-EDH420) est conforme aux CNR d´Industrie Canada applicables aux appareils radio exempts de licence. L´exploitation est autorisée aux deux conditions suivantes: 1. I'appareil ne doit pas produire de brouillage; 2. I'utilisateur de I´appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d´en compromettre le functionnement . All contents current at time of publication. 117C V1.0 07/23/2021Microsoft PowerPoint 2016 Microsoft PowerPoint 2016