Manuals+

MYX Fitness Product Manual

Model: MYX Bike

Safety Information

⚠️ WARNING: CAREFULLY READ AND FOLLOW ALL SAFETY AND OTHER INSTRUCTIONS IN THIS MANUAL BEFORE USING THE PRODUCT. FAILURE TO DO SO MAY RESULT IN DEATH OR SERIOUS INJURY TO YOU AND/OR OTHERS:

Notices

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  1. Reorient or relocate the receiving antenna.
  2. Increase the separation between the equipment and receiver.
  3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  4. Consult the dealer or an experienced radio/TV technician for help.

Product Overview

SPECIFICATIONS

Weight150 lbs (68 kg)
Width21" (53 cm)
Length55" (140 cm)
Height47" (119 cm)
Max User Weight350 lbs (159 kg)
Required User Height4'11" - 6'8"

A visual representation of the MYX Fitness bike is shown, including the tablet, handlebars, seat, pedals, and frame. Accessories like dumbbells, a kettlebell, and a yoga mat are also depicted.

Product Features

MYX Bike Features

The MYX Bike features include:

MYX Tablet Features

The MYX Tablet features include:

Hardware Setup

MOVING THE BIKE

⚠️ WARNING: This product must be set up and operated on a solid level surface. If your bike is not level, adjust the four leveling feet located on the underside of the front and rear legs until all four feet are evenly contacting the floor.

⚠️ CAUTION: Use two people to move the product, since it weighs over 150 lbs (68 kgs).

  1. Have one person lift the rear stabilizer to tilt the bike forward onto the transport wheels, while the other person holds the handlebars.
  2. Roll the bike forward to the new location.
  3. Lower the rear stabilizer to the floor.
  4. Unscrew leveling feet if needed to prevent rocking on uneven floors.

Diagrams illustrate the steps for moving the bike: tilting it onto wheels, rolling it, and adjusting leveling feet.

TABLET AND MOUNTING ARM

Your tablet will be assembled by the setup team, but it can be easily removed and reattached for ease of transportation later.

⚠️ CAUTION: Use two people to remove or reattach the tablet and mounting arm.

Disassembly

  1. Remove the plastic covers to reveal the mounting screws. Have one person support the tablet while the other person uses the 4mm Phillips screwdriver from the toolkit to remove the four 4mm screws at the back of the tablet.
  2. Lift off the tablet and set the screws aside.
  3. Have one person support the mounting arm, while the other loosens and removes the two 9mm screws.
  4. Remove the mounting arm and the oval mounting plate.

Assembly

  1. Align oval mounting plate with the two holes at the center of the bottle holder bracket.
  2. Align mounting arm below the bottle holder bracket.
  3. Insert and tighten two 9mm mounting screws through the oval plate, bracket holes, and into the holes on the mounting arm.
  4. Align the tablet with the 4-hole plate at the top of the mounting arm.
  5. Insert four 4mm screws through the plate and into the mounting holes in the back of tablet and tighten. Replace the plastic covers.

Diagrams illustrate the disassembly and assembly steps for the tablet and mounting arm.

CONNECT POWER CORD

Thread the small end of the power cord from the bottom of the mounting arm to the hole at the bend in the arm. Pull the wire through the hole and connect to tablet, allowing 8-10" of slack so the tablet can swivel freely. Connect the wall adapter to the plug below the flywheel and a grounded 120V wall outlet.

A diagram shows the power cord routing and connection, indicating the 8-10" slack.

ADJUSTING SEAT AND HANDLEBAR HEIGHT

Seat and handlebars can be raised and lowered with the adjustment pins at the front and rear of the bike frame.

⚠️ CAUTION: Adjust the seat and handlebars with two people due to the weight of the handlebars with tablet attached.

  1. Turn pins counterclockwise to unscrew.
  2. If adjusting the handlebars, have your assistant support the weight of the handlebars from beneath.
  3. Pull the pin outward and then raise or lower the post.
  4. Release the pin so it locks into the post at the desired height, and tighten the knob to secure it in place.

⚠️ CAUTION: Do not lift the seat or handlebar posts above the MAX mark.

⚠️ CAUTION: Do not use the product if the seat or handlebars are not securely and tightly locked into place.

⚠️ CAUTION: Ensure power cord is out of the way when adjusting the height.

Diagrams illustrate the process of turning the pin, supporting the handlebars, pulling the pin, and locking the post.

ADJUSTING SEAT AND HANDLEBAR DEPTH

Seat Depth

  1. Loosen the knob under the seat slider by turning it clockwise.
  2. Push the seat forward or backward to adjust position, and tighten the knob to secure into place.

A diagram shows the seat adjustment knob and slider mechanism.

Handlebar Depth

  1. Loosen the knob between the handlebars by turning it counterclockwise.
  2. While supporting the weight of the tablet arm with one hand, slide the handlebars forward or backward to adjust position.
  3. Tighten the knob to secure into place.

Diagrams illustrate the handlebar depth adjustment process.

MOUNT AND DISMOUNT

⚠️ WARNING: To avoid injury or death, the following procedures must be followed to safely mount and dismount the product. Do not mount or dismount the product (or remove your feet from the pedals) until both the pedals and flywheel have come to a complete stop. Mounting or dismounting while pedals are moving can seriously injure user.

To mount the product safely:

  1. Verify the product is fully stopped and pedals are completely stopped.
  2. Grasp handlebar and step carefully onto pedals.

To dismount the product safely:

  1. Wait until the pedals and flywheel come to a complete stop. Stop the pedals using ANY of the following methods:
    • Slow your pedaling until the pedals come to a complete stop.
    • Increase the resistance by turning the push brake system knob clockwise (+) until the pedals come to a complete stop.
    • Push down and hold the resistance knob until the pedals come to a complete stop.
  2. Once the pedals and flywheel are stopped, remove feet from pedal clips or cages, as applicable.
  3. Grasp handlebars firmly for support and carefully step down.

Emergency Dismount:

If an emergency stop and dismount is required:

  1. Stop pedaling. The fastest way to stop is to push down and hold the resistance knob until the pedals come to a complete stop.
  2. Once the pedals and flywheel are stopped, remove feet from pedal clips or cages, as applicable.
  3. Grasp handlebars firmly for support and carefully step down.

ADJUSTING RESISTANCE

The resistance knob is located at the base of the handlebar post. Note that it takes several full turns to feel changes in resistance.

  1. Rotate right to increase resistance.
  2. Rotate left to decrease resistance.
  3. Press down on the knob to stop the flywheel.

Diagrams illustrate rotating the knob right, left, and pressing down.

USING PEDAL CLIPS AND CAGE

To use the product with SPD clips:

  1. Install the cleats on your SPD-compatible shoes according to the manufacturer's instructions.
  2. Make sure the pedal is flat and right-side up.
  3. Place the cleat on your shoe into the clip and push down.
  4. To release the clip, simply twist your heel away from the bike until your shoe disengages from the pedal.

⚠️ CAUTION: The product is intended to be used with SPD-compatible clips. Do not use any other type of clips.

Diagram A shows the SPD pedal clip mechanism.

To use the product with cages, you must use athletic shoes:

You'll use the cages on the reverse of the pedal.

⚠️ CAUTION: First, make sure your shoelaces are tied, tucked away and not dangling over your foot.

  1. Insert your foot through the cage. Align the ball of your foot over the center of the pedal, and pull the strap tightly to tighten the cage. Thread the excess strap through the metal clip.
  2. Repeat on the other side.
  3. To remove your foot, squeeze and release the bottom of the metal clip to release the tension grip and loosen the cages. Then you can slide your foot out of the cage.

Diagram B shows the pedal cage mechanism.

Speed Sensor (MYX II ONLY)

REPLACE BATTERY

The speed sensor is located on the inner side of the left pedal crank. When the app indicates the sensor battery is low, replace it with a new CR-2032 coin cell battery. Expected battery life is 100 hours.

  1. Turn the battery cover counter clockwise to open.
  2. Remove the old battery from the metal holder and replace it with a new battery. Make sure the negative side faces up (toward the battery cover).
  3. Replace the battery cover. Align it in the top slot, then turn clockwise using your fingernail in the groove to guide it. LED lights will flash to indicate the battery has proper placement.

Diagrams illustrate the battery replacement process.

TUNE YOUR SENSOR

If you have trouble with speed, cadence or distance tracking you can follow instructions within the tablet app to re-tune your sensor.

WAKE YOUR SENSOR

Pedal for two minutes to wake the speed sensor.

Heart Rate Monitor Setup

CHARGE BATTERY

A red light indicates your heart rate monitor needs to be charged.

  1. Place the OH1 sensor into the USBA adapter so that the metal contacts meet.
  2. Insert the adapter into the dongle, then plug the small end into the USBC port at rear of the tablet. Check for the orange light which indicates the USB has been inserted correctly. For MYX II, insert the adapter into the dongle.

A flashing yellow light indicates it is charging. A green light indicates that it is fully charged.

Diagrams show the charging adapter and connection for MYX I and MYX II.

USING YOUR HEART RATE MONITOR

  1. Remove the sensor from the charging adaptor, and place it in the holder on the arm band so the sensing side is exposed.
  2. Put the arm band on your upper forearm or bicep so that the sensor touches your skin.
  3. Press the silver button once to turn on. A blinking green light means it has detected your heartbeat.
  4. Choose a workout on the MYX tablet. At the top right of the workout details screen, choose Tap to Pair "HR Monitor". Your heart rate monitor can also be paired by pressing the heart-shaped icon during a workout.
  5. After your workout, press and hold the OH1 button to turn off the heart rate monitor.

⚠️ WARNING: Please consult your physician before engaging in heart rate training, especially if you are pregnant, are younger than 18 years old, have any underlying medical conditions, or are unsure about pushing your heart rate to the max. If you are younger than 18 years old, please also get your parent or guardian's permission before beginning.

Tablet Setup

POWERING ON THE TABLET

Ensure the tablet is connected to an appropriate power source. Press and hold the power button on the right side of the tablet for five seconds to power on.

To enter or exit sleep mode, quickly press the power button.

To turn off the tablet, press and hold the power button for one second, and select Power Off on the screen.

CONNECTING TO INTERNET

A strong internet connection with a minimum download speed of 10-15 MBPS is required to stream MYXfitness content. After powering on your device, follow the on screen instructions to select your wireless network.

To use ethernet, run an ethernet cord from your router to the leftmost port at the bottom of the tablet, and your device should automatically join the network.

⚠️ WARNING: Ensure the Ethernet cord does not interfere with you, your exercise or the product. For example, ensure the cord does not interfere with any moving parts, such as the flywheel or pedals.

Caring for Your MYX

MAINTENANCE

Preventative maintenance can extend the life of your product and significantly reduce equipment failures. The chart provided is our recommended maintenance schedule. It is your responsibility to ensure that regular maintenance is performed.

⚠️ WARNING: Worn or damaged parts must be replaced immediately, and should not be used until the repair is made.

CLEANING

We recommend wiping down and cleaning the product frame daily. For a deeper clean use water with a non-abrasive soap, car wash soap, or bike cleaner. Wipe with water and dry. Avoid spraying any liquids directly onto the product. Instead, spray onto a clean towel first then wipe the product. You may also seal the frame with wax or bike polish.

CHECKLIST

TaskWeeklyMonthly
Inspect for loose nuts or bolts on handlebar and seat assembly and tighten as necessary.X
Verify that pedal bolts connecting pedals to bike crank are tight after the first 10 hours of use and every 100 hours of use thereafter. Tighten (clockwise) with a 15mm box wrench.X
Inspect pedals for excessive wobble or side-to-side movement. If loose, they need to be replaced.X
Check flywheel alignment. Realign flywheel nuts as necessary.X
Tighten seat hardware (bolt connecting seat to post)X
Lubricate horizontal and vertical sliders (for seat and handlebars) with dry film lubricant with PTFE or wet film lubricant with PTFE. Apply a layer and use a cloth to clean up excess.X
Inspect welds for any signs of crackingX
Inspect leveling feetX
Check for rust and remove any minor buildup found using a small brush.X
Inspect the seat for wear and tear. Rips, tears, or excessive movement indicate the seat needs to be replaced.X
Inspect pedal toe clips and straps for any looseness or excessive wear. Replace if toe clips cannot be tightened to pedal or if the strap shows excessive wear.X

Warnings and Cautions

To replace any worn or damaged decals contact customer support to order new labels: help@myxfitness.com

⚠️ WARNING: Read the Owner's Manual and follow all proper instruction prior to use. IMPROPER USE OF THIS MACHINE CAN RESULT IN SERIOUS INJURY.

  1. As with all exercise equipment or programs, consult a physician prior to use and stop if you feel faint, dizzy or exhausted.
  2. This equipment should only be used in a supervised environment.
  3. Keep children away from bike.
  4. Inspect machine prior to use. Immediately report worn, loose or damaged equipment to the instructor and refrain from using the bike.
  5. Keep body and clothing free and clear of all moving parts.
  6. Ensure all adjustment and locking features are properly secured before using bike.
  7. Always ride in control. Stop in a controlled manner as flywheel momentum will keep pedals turning.
  8. Maximum user capacity is 350 lbs (158.8 Kg).
  9. Verify that pedals connecting to the bike cranks are tight after the first 10 hours of use and every 100 hours of use thereafter. Tighten each pedal to a torque of 33-37 ft-lbs.
  10. Replace label if damaged, illegible or removed.

⚠️ WARNING: LEFT CRANK: Tighten pedal marked "L" to 33-37 ft-lbs. After the first 10 hours of use and every 100 hours of use thereafter, re-tighten pedal to a torque of 33-37 ft-lbs.

⚠️ WARNING: RIGHT CRANK: Tighten pedal marked "R" to 33-37 ft-lbs. After the first 10 hours of use and every 100 hours of use thereafter, re-tighten pedal to a torque of 33-37 ft-lbs.

Limited Product Warranty

MYX FITNESS® EXERCISE BIKE LIMITED PRODUCT WARRANTY

1. WARRANTY OVERVIEW

The Myx Fitness exercise bike (the “Myx Fitness Bike") you have purchased from Myx Fitness, LLC ("Myx Fitness") either alone or with Myx Fitness home studio accessories ("Accessories") comes with a limited product warranty (the “Limited Product Warranty") covering only the Myx Fitness Bike, Accessories, software of any kind (excluding music functionality and selection) embedded in your Myx Fitness tablet that is a component of your Myx Fitness Bike ("Product Firmware"), and the components of the Myx Fitness Bike expressly described below, and which can be identified by the Myx Fitness trademark, trade name, or logo annexed or affixed to such items (other than Product Firmware), for the period of time set forth below. The Myx Fitness Bike, Accessories, Product Firmware and the components of the Myx Fitness Bike expressly described below are collectively referred to in this Limited Product Warranty as, "Product."

This Limited Product Warranty is valid only if: (i) you use the Product within a private, in-home, domestic, indoor, non-commercial environment and in accordance with the Myx Fitness Bike product manual, unless otherwise approved in advance in writing by Myx Fitness; and (ii) you are in good standing and in compliance with the Myx Fitness Terms and Conditions available on the Myx Fitness website (https://www.myxfitness.com/terms-of-service). Certain other exclusions apply, as further described in this Limited Product Warranty.

This Limited Product Warranty is non-transferable and is only valid for the original purchaser of the Myx Fitness Bike, or for a Myx Fitness Bike gifted at the time of purchase, the member of the original membership first used to access and use live and on demand exercise content on that specific Myx Fitness Bike.

The Limited Product Warranty applies as follows:

Except where applicable law requires otherwise, repair labor is not covered for locations where Myx Fitness did not originally assemble the Myx Fitness Bike or if the Myx Fitness Bike is moved to a location that is outside of Myx Fitness's service area. Any attempt to move or repair fitness equipment creates a risk of injury and property damage. All moves or repairs attempted by you or your agents are undertaken AT YOUR OWN RISK and none of the Myx Fitness Parties will have any liability for any injury to persons or property arising from such attempted moves or repairs.

If (a) a defect in material or workmanship arises with your Myx Fitness Bike, Accessories, or any of the components thereof or a material defect that cannot be corrected or repaired remotely by Myx Fitness arises with your Product Firmware, (b) your Product has been used in accordance with the terms and conditions of this Limited Product Warranty, (c) a valid Limited Product Warranty claim is received by Myx Fitness within the applicable warranty period set forth above in accordance with the terms of this Limited Product Warranty, and (d) you are in good standing and in compliance with the Myx Fitness Terms and Conditions available on the Myx Fitness website (https://www.myxfitness.com/terms-of-service), Myx Fitness will, in its sole and absolute discretion and to the extent permitted by applicable law, either repair or replace, at its option, the applicable defective Product component with one that is new or equivalent to new (i.e., refurbished) in performance and reliability and is at least functionally equivalent to the original Product component.

Where permitted by law, replacement units, parts and electronic components reconditioned to as-new condition by Myx Fitness or its vendors may sometimes be supplied as warranty replacement and constitute fulfillment of warranty terms.

If the defective Product component is shipped to a service center, freight charges to and from the service center may be your responsibility. For replacement parts shipped while the Product is under warranty, you may be responsible for a minimal handling charge. For in-home service while the Product is under warranty, you may be responsible for a minimal trip charge. MYX FITNESS DOES NOT PROVIDE MONETARY OR OTHER COMPENSATION FOR ANY REPAIRS OR REPLACEMENT PART COSTS IN CONNECTION WITH THE PRODUCT, INCLUDING WITHOUT LIMITATION, MEMBERSHIP FEES, WORKOUT TIME LOST, COST OF SUBSTITUTE EQUIPMENT, DIAGNOSTIC VISITS, MAINTENANCE VISITS OR TRANSPORTATION.

Any replacement or repaired Product will be warranted for the remainder of the original applicable Limited Product Warranty period or 30 days, whichever is longer, or for any additional period that is required by applicable law.

No other warranty beyond that specifically set forth above is authorized by Myx Fitness.

2. EXCLUSIONS AND LIMITATIONS

This Limited Product Warranty does not extend to and may be voided by Myx Fitness in its sole and absolute discretion for any of the following:

Myx Fitness does not warrant that the use and/or operation of the Product will be uninterrupted or error free. In addition, although Myx Fitness may provide periodic updates to the Product Firmware, this Limited Product Warranty does not apply in the event that any Product Firmware needs to be upgraded for any reason. This Limited Product Warranty does not cover any loss, damage or defects caused by a defective function of any wireless network or if any Product Firmware needs to be upgraded due to changes in wireless network parameters.

THIS LIMITED PRODUCT WARRANTY IS THE EXCLUSIVE WARRANTY GIVEN BY MYX FITNESS FOR THE PRODUCT AND SUPERSEDES ANY PRIOR, CONTRARY OR ADDITIONAL WARRANTIES OR REPRESENTATIONS. EXCEPT FOR THE WARRANTIES EXPRESSLY PROVIDED UNDER THIS LIMITED PRODUCT WARRANTY, ALL OTHER WARRANTIES, EXPRESS, IMPLIED OR STATUTORY, WITH RESPECT TO THE PRODUCT, WHETHER AS TO CONDITION OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, NON-INFRINGEMENT, TITLE, QUIET ENJOYMENT OR ANY OTHER MATTER, ARE DISCLAIMED, EXCEPT TO THE EXTENT PROHIBITED BY LAW. IN SUCH EVENT, SUCH WARRANTY IS LIMITED TO THE DURATION OF THE WARRANTY PERIODS SET FORTH ABOVE. THIS EXCLUSION APPLIES EVEN IF THIS WARRANTY FAILS OF ITS ESSENTIAL PURPOSES AND REGARDLESS OF WHETHER DAMAGES ARE SOUGHT FOR BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, OR STRICT LIABILITY IN TORT OR UNDER ANY OTHER LEGAL THEORY.

THE REMEDIES SET FORTH IN THIS MYX FITNESS LIMITED PRODUCT WARRANTY WILL BE THE SOLE AND EXCLUSIVE REMEDIES AVAILABLE TO ANY PERSON OR ENTITY.

UNDER NO CIRCUMSTANCES WILL MYX FITNESS, ITS PARENT COMPANY, SUBSIDIARIES, AFFILIATES, MANUFACTURERS, SERVICE PROVIDERS, LICENSORS, DISTRIBUTORS, SUPPLIERS AND EACH OF ITS AND THEIR RESPECTIVE PARENT COMPANIES, SUBSIDIARIES, AFFILIATES, OFFICERS, DIRECTORS, MANAGERS, PARTNERS, MEMBERS, SUCCESSORS AND ASSIGNS (COLLECTIVELY, THE "MYX FITNESS PARTIES") BE SUBJECT TO ANY CONSEQUENTIAL, INCIDENTAL, INDIRECT, SPECIAL, EXEMPLARY, PUNITIVE OR CONTINGENT DAMAGES WHATSOEVER, RELATED TO OR ARISING OUT OF THIS LIMITED PRODUCT WARRANTY OR THE USE OF THE PRODUCT, WHETHER BASED ON CONTRACT, TORT, STRICT LIABILITY OR OTHER THEORY OF LAW, ALL SUCH DAMAGES AND CLAIMS BEING SPECIFICALLY DISCLAIMED.

ANY DISPUTES BETWEEN YOU AND MYX FITNESS RELATED TO THIS LIMITED PRODUCT WARRANTY OR THE PRODUCT WILL BE GOVERNED BY THE THEN-CURRENT DISPUTE RESOLUTION PROCEDURES IN THE MYX FITNESS TERMS AND CONDITIONS, AVAILABLE AT (https://www.myxfitness.com/terms-of-service).

NOTWITHSTANDING ANY DAMAGES THAT YOU MIGHT INCUR FOR ANY REASON WHATSOEVER (INCLUDING, WITHOUT LIMITATION, ALL DAMAGES REFERENCED HEREIN AND ALL DIRECT OR GENERAL DAMAGES IN CONTRACT, TORT (INCLUDING, WITHOUT LIMITATION, NEGLIGENCE) OR OTHERWISE, THE ENTIRE AGGREGATE LIABILITY OF THE MYX FITNESS PARTIES WILL BE LIMITED TO THE AMOUNT ACTUALLY PAID BY YOU FOR THE PRODUCT (BUT EXCLUDING ALL AMOUNTS PAID FOR THE ONGOING MEMBERSHIP) GIVING RISE TO LIABILITY.

Without limiting any of the foregoing and in addition thereto, in no event, under any cause of action or theory of liability, will the Myx Fitness Parties be liable to you or any third party for any (a) accident, personal injury or death or property damage or any other claims, losses, costs or damages, related to, arising out of or resulting from the purchase, sale, use of or inability to use the Product, or the performance or provision of services by Myx Fitness pursuant to this Limited Product Warranty or otherwise, the loss of value of the Product or any third party accessories, services, products or devices that are used in or with the Product, or the loss of use of the Product or any third party accessories, services, products or devices that are used in or with the Product, even if any Myx Fitness Party has been advised of the possibility of such damages; (b) damage or destruction to consumer electronics devices or other personal property that are contained inside or outside, or used in connection with, the Product, including, without limitation, mobile apps, tablets, laptops, cellular phones, or other handheld devices, or for any loss of data stored in the foregoing devices or elsewhere; and (c) costs or damages arising from or related to your breach of the terms of this Limited Product Warranty. The Myx Fitness Parties disclaim any representation that they will be able to repair any product under this Limited Product Warranty or make a product exchange without risk to or loss of electronic information, including programs or data.

The foregoing limitations of liability constitute an essential part of this Limited Product Warranty. In some jurisdictions, under some circumstances, the limitations and disclaimers of liability contained in this Limited Product Warranty do not apply to claims involving personal injury, claims of wrongful death, claims of damage to property or to statutory liability for intentional or grossly negligent acts and/or omissions. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Nevertheless, Myx Fitness intends that the limitations and disclaimers of liability contained in this Limited Product Warranty will apply to the maximum extent allowed under applicable law. If applicable law specifies a minimum warranty period that is longer than the applicable warranty periods set forth in the terms and conditions of this Limited Product Warranty, then the warranty period for the applicable Product component subject to such applicable law will be conformed to the minimum legally required warranty period. The limitations and disclaimers of liability set forth in this Limited Product Warranty survive the expiration or termination of the warranty periods set forth in this Limited Product Warranty and apply notwithstanding any contrary provision in this Limited Product Warranty. This warranty gives you specific legal rights, and you may also have other rights which vary from State to State.

3. WARRANTY CLAIMS AND QUESTIONS

To be eligible for service under this Limited Product Warranty you must provide Myx Fitness with the serial number of your Myx Fitness Bike and the dated receipt, or other proof of purchase indicating the date purchased, upon discovering any defect. Claims must be made within the specified warranty periods listed above.

To file a warranty claim, or for any questions or concerns, please contact member support by emailing us at help@myxfitness.com for fastest service and response time.

You may also write to us at:

Myx Fitness, LLC
Attention: Limited Product Warranty Claims
3301 Exposition Blvd.
Santa Monica, California 90404
Rev: August 27, 2021

Appendix

WARRANTY INFORMATION

Visit myxfitness.com/warranty

CONTACT

Help Center
help.myxfitness.com

Customer Support
help@myxfitness.com

Myx Fitness, LLC
3301 Exposition Blvd.
Santa Monica, CA 90404

Please supply the serial number of your machine and the date of purchase when you contact us. The serial number is found under the rear leg of the machine (see diagram on page 6).

Models: MYX II Plus, Indoor Exercise Bike

File Info : application/pdf, 23 Pages, 7.41MB

PDF preview unavailable. Download the PDF instead.

MYX Fitness Product Manual 2021 ?v=1632326170 Adobe PDF Library 16.0 Adobe InDesign 16.4 (Macintosh)

Related Documents

Preview FCC ID Label Location for MYX2 Power Meter Crank
This document details the FCC ID label location for the MYX2 Power Meter Crank, identifying the FCC ID as 2AUR9P5-MYX2 and illustrating its placement on the device.