User Manual for Shenzhen Jimi IoT Co Ltd models including: LL701 GPS Device, LL701, GPS Device, Device
Shenzhen Jimi IoT Co., Ltd. LL701 2AMLF-LL701 2AMLFLL701 ll701
LL701 User Manual Version: V1.0 Read this manual carefully prior to use to ensure fast and correct operation of the product. No prior notice will be given for any changes made to the appearance, color, or accessories of the product. Product Overview Standard Parts List Item LL701 Magnetic mount Double-sided tape Batteries Quantity 1 1 1 3 Specification GNSS Positioning system Frequency Positioning accuracy Tracking sensitivity Acquisition sensitivity TTFF (open sky) GPS+LBS+WiFi+Bluetooth GPS+WiFi+Bluetooth GPS+WiFi+Bluetooth, LBS (optional) GPS L1 C/A supported QZSS L1 C/A supported < 2.5m CEP 155dBm 145.5 dBm (cold start); 147 dBm (hot start) Avg. hot start: 1 second Avg. cold start: 36 seconds Cellular Communication network LTE Frequency bands LTE CAT-M1: B1, B2, B3, B4, B5, B8, B12, B13, B14, B18, B19, B20, B25, B26, B28, B66 LTE CAT-NB1/NB2: B1, B2, B3, B4, B5, B8, B12, B13, B17, B19, B20, B25, B26, B28, B66 Power Working modes Standby time Interface LED indication SIM Tamper proof Mode 1: Power-saving mode Mode 2: Regular GPS mode Mode 3: Power-off mode Up to 5 years (one fix per day) GNSS (Blue), Cellular (Green), Power (Red) Micro-SIM Light sensor Product Setup Open the socket lid; Place the SIM card into the socket (metal side downward); Close the socket lid (if the SIM card is incorrectly placed, the lock will fail). LED Indication Battery Indication When the device runs in recycling mode, press its function button for 3 seconds and the power LED will light on for 4 seconds to tell you the strength of the internal battery. LED Status 4 LEDs on 3 LEDs on 2 LEDs on 1 LED on 1 flashing LED Battery Strength 80% to 100% 50% to 79% 30% to 49% 10% to 29% 1% to 9% Min. standby time 1550 days 950 days 550 days 190 days Exhausting Note: The min. standby time is estimated on the ground that the device generates one fix per day. GNSS Indication The GNSS LED is used to show the working status of the device's GNSS module, where: Flashing rapidly [onoff (0.1s0.1s)]: The device is searching for satellite signals; Always on: A position has been fixed; Off: The GNSS module isn't working. Cellular Indication The cellular LED is used to show the network status of the device, where: Flashing slowly [onoff (0.1s0.5s)]: The device is identifying the SIM card; Flashing rapidly [onoff (0.1s0.1s)]: The device is receiving cellular signals; Flashing slowly [onoff (0.1s0.1s)]: The device is online; Off: The device fails to receive cellular signals or no SIM card is identified. Configuration APN Setting (If no network is available, you are advised to set the APN via the mobile app JIMI IoT LAB) Command: APN,<N>[,U][,P]# N: Network name U: User name P: User password Note: The parameters "U" and "P" can be left empty. The command is "CMNET#" by default. APN adaptation switch: ASETAPN,<SW># SW: Switch to enable or disable the APN adaptation feature, whose value is either "ON" or "OFF". Note: The default value for "SW" is "ON". Comparing these two setting methods, the priorities of manually-set APNs are higher than the self-adapted ones. Once an APN is manually changed (via a command sent by the user), the adaptation feature will turn invalid (auto switched to OFF). This auto switch-off protects the device against failing to go online in the event of an APN recognizing failure or an incorrect APN. Working Modes Recycling mode (Mode1) In recycling mode, the device will disable the cellular and GNSS modules, which means it will neither fix positions nor upload location data. Standby mode (Mode2) In standby mode, the device uploads a position fix every 24 hours by default. You can change the interval and time point of upload via a command delivered by the platform or via the Jimi IoT LAB mobile app. Set command: MODE,2,Time,Interval# Time: 00:01 to 23:59 (default: 07:00) Interval: 60 to 1440 (default: 1440 minutes) Tracking mode (Mode3) In tracking mode, the device uploads a position fix every minute. You can change the upload and positioning duration via a command delivered by the platform or via the Jimi IoT LAB mobile app. Set command: MODE,3,interval,Working Time# Interval: 60 to 360 (unit: seconds; default: 60 seconds) Working Time: 0 to 1440 (unit: minutes; default: 10 minutes) Note: If the working time is set to "0", the device will not exist tracking mode. Switching Modes Switch by command: MODE[,A]# A: 1 for recycling mode, 2 for standby mode, 3 for tracking mode Query current working mode: MODE# Switch by key press: If the device is in recycling mode, press the function button for 5 seconds to switch to standby mode; If the device is in standby mode, short press the function button for 3 times in 5 seconds to switch to recycling mode. Troubleshootintg When a problem arises, you can troubleshoot it by the following solution. If the problem persists, please don't hesitate to contact your dealer or service provider. Warranty Instructions Special Statement No prior notice will be given if the product is upgraded due to technological reasons. The appearance or color of the product is subject to the actual. The warranty card applies to the services of repair, replacement, and refund of the product with the following IMEI. Please keep this warranty card and the original purchase receipt together in a safe place, as these will be needed at time of services. Warranty Terms For damages not caused by human factors, this warranty lasts for 2 (two) years (including one-year replacement service) from the date of the original purchase. You can choose to pay for the repair services in any of the following cases: The warranty card expires; No warranty card or valid proof of purchase; The product, including its accessories, is not in the warranty period; Damage caused by unauthorized repairs, crash, liquid spillage, incident, accident, modifications, or incorrect voltage input; or the label, IMEI, or counterfeit mark of the product is broken or scribbled; Damages caused by installation or use not in accordance with the user manual; Damage caused by force majeure such as fire, flood, or lightning; The device model is inconsistent with the warranty card or the warranty card has been altered; Other damages caused by force majeure. FCC warning Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.Adobe PDF Library 15.0 Adobe InDesign 16.0 (Windows)