LLOYTRON Daybreak AM/FM Radio Alarm Clock J2006
Operating Instructions
Introduction
Thank you for purchasing this LLOYTRON product. Used carefully and in accordance with these instructions, it should provide long, trouble-free service. Please keep these instructions for future reference.
Features
- AM/FM Radio
- 24hr Red LED Clock Display
- Radio or Buzz Alarm
- Snooze Function
- Sleep Timer Function
- Rotary Volume and Tuning Controls
- Mains Operation
- PP3 9v Back-up Battery (Not Included)
Visual Description of Product: The device is a compact, rectangular alarm clock radio with a dark casing. The front features a large, bright red LED display showing the time (e.g., 12:00). Below the display are markings for AM and FM radio frequencies. The top surface has several buttons labeled SLEEP, TIME, ALARM, SNOOZE, HOUR, and MIN. A rotary dial is visible on the side for tuning and volume control.
Specifications
- Operating Voltage: 220-240v~50Hz
- Backup Battery Requirement: PP3 9v (not included)
- Radio Frequency Range: AM: 530 – 1600kHz, FM: 88 - 108MHz
Important Safeguards and Precautions
SAVE THESE INSTRUCTIONS
- Read all instructions carefully.
- For Household Use only.
- Only for use indoors.
- ? DO NOT use outside or in damp conditions.
- ? DO NOT use for any purposes other than the appliance's intended use.
- ? DO NOT use if any part of this appliance is damaged in any way.
- To prevent risk of electric shock, do not submerge any part of this appliance in water, unless advised in this manual.
- This appliance should only be used on a flat surface.
- ⚠️ To prevent possible hearing damage, do not listen at high volume levels for long periods.
- This appliance is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance, by a person responsible for their safety.
- Children should be supervised to ensure they do not play with this appliance.
- Cleaning and user maintenance shall not be made by children.
- Never let children push anything into holes or slots in the cabinet or casing – this could result in an electric shock.
- Before plugging into mains socket, check whether supply line voltage and current rating are in compliance with the rated electrical parameters shown on the rating label.
- To prevent damage to the mains cord, do not let it pass over sharp corners, edges or hot surfaces.
- If the supply cord is damaged, do not use. Check before each use!
- If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.
- Always unplug when not in use.
- ? DO NOT use rechargeable batteries in this appliance.
- Always turn the unit off when not in use. Leaving it on will shorten the life of the batteries.
- If you plan not to use the unit for a length of time, remove the batteries. Old batteries can leak and cause corrosion, damaging the unit.
- The use of long-life alkaline batteries is recommended.
- DON'T throw the battery in fire or dispose of in household waste. Consult your local authority for the correct way to dispose of unwanted batteries.
- DON'T short-circuit the supply terminals of the battery.
- Always check the correct polarity when inserting the battery. Incorrect polarity can damage this unit.
Location of Controls
The appliance has the following controls and features:
- A - Function Switch: Toggle the switch to 'on' for continuous playback of the radio. Toggle to 'off' to turn the Radio to standby. Setting the switch to 'auto' leaves the radio on standby until the alarm time is reached, at which point the radio will turn on to wake the user.
- B – AM/FM Tuning Dial: This dial indicates the frequency being received by the radio.
- C - Sleep Timer Button: Press and hold this button and use the hour and minute buttons to set the sleep timer. This allows a predetermined length of time for the radio to play until it switches off, up to 2 hours.
- D - Time Button: Press and hold this button and use the hour and minute buttons to set the clock time.
- E - Alarm Button: Press and hold this button and use the hour and minute buttons to set the alarm time.
- F - Snooze Button: Press this button while the alarm is sounding for an extra 9 minutes (approx.) of sleep.
- G - Hour button: Press repeatedly to set the hour on the clock.
- H - Minute button: Press repeatedly to set the minute on the clock.
- I – Rotary Tuning Control: Use this control to move the dial along to locate a station of your choice.
- J - Band Selector Switch: Use this switch to select between AM & FM radio bandwidths.
- K – Rotary Volume Control: Use this control to increase or decrease the volume. Turning the volume control to 'Buzz' will cause the unit to beep when the alarm is triggered instead of operating the radio.
- L - Speaker: Outputs the audio from the radio.
- M - Battery Compartment: Located on the back, this compartment holds 1 x PP3 9v Battery (not included) for backup power.
- N - Multi-Directional Antenna: Unwind and let this antenna hang to improve reception. It is multi-directional.
- O - Power Cord: Connects to a suitable 220-240v~50Hz mains supply.
Visual Description of Controls: The top surface of the clock radio features several buttons arranged in a row: SLEEP, TIME, ALARM, SNOOZE, HOUR, MIN. The front display shows the time. The sides feature rotary dials for tuning and volume. The band selector (AM/FM) is typically a switch. The power cord extends from the back.
Operation
Radio Operation
- Turn the volume control fully CLOCKWISE to OFF before use. This protects against hearing damage as volume can be gradually increased.
- TOGGLE the function switch to the 'ON' position to OPERATE the radio.
- TOGGLE between AM & FM on the band selector switch to choose between AM or FM wavebands.
- SLOWLY TURN the volume control dial ANTI-CLOCKWISE to gradually INCREASE the volume. The dial will CLICK to indicate it is operational. Keep rotating to find a suitable listening volume.
- Use the tuning control to BROWSE through the frequencies within AM or FM wavebands to find a suitable radio station. Use the AM/FM tuning dial to CHECK the frequency.
- UNWIND the antenna cable and let it HANG to help IMPROVE reception.
- After use, SWITCH the radio OFF by toggling the function switch to the 'OFF' position.
Setting the Time
- PRESS and HOLD the Time Button.
- CONTINUING to HOLD the Time button, REPEATEDLY PRESS the Min button to set the minute counter on the clock. The minute counter cycles from 00:00 - 00:59.
- CONTINUING to HOLD the time button, REPEATEDLY PRESS the Hour button to set the 24-hour counter on the clock. The hour counter cycles from 00:00 – 23:00.
- RELEASE the time button. The time is now set.
Note: The numbers will only go up, so if you miss the intended number, you will need to cycle back through the range of numbers again.
Note: This is a 24-hour clock; therefore, if the time is 8pm, the clock needs to be set to 20:00.
Setting the Alarm
- ENSURE that the time is set correctly using the 'Setting the Time' section.
- PRESS and HOLD the Alarm button.
- CONTINUING to HOLD the Alarm button, REPEATEDLY PRESS the Min button to set the minute counter on the clock. The minute counter cycles from 00:00 - 00:59.
- CONTINUING to HOLD the Alarm button, REPEATEDLY PRESS the Hour button to set the 24-hour counter on the clock. The hour counter cycles from 00:00 – 23:00.
- RELEASE the Alarm button.
- TOGGLE the function switch to AUTO. The alarm will sound at the set time.
Note: The numbers will only go up, so if you miss the intended number, you will need to cycle back through the range of numbers again.
Note: This is a 24-hour clock; therefore, if the user needs to wake at 8am, the alarm needs to be set at 08:00. If the user requires the alarm to sound at 8pm, the alarm needs to be set at 20:00.
Alarm Sound Options:
- SET the volume dial to BUZZ MODE if you wish to be woken by the buzzer.
- SET the volume dial to a SUITABLE volume level if you wish to be woken by the radio.
The alarm will sound at the time set by the alarm.
Snooze Function, Disengaging the Alarm, and Battery Backup
Snooze Function: When the alarm sounds, press the snooze button for approximately 9 minutes of extra sleep. The alarm will sound again after this period. To cancel the snooze function, toggle the function switch to the off position.
Disengaging the Alarm: Once the alarm sounds, toggle the function switch to the off position to disengage the alarm, or by pressing the SLEEP or ALARM button.
9V Battery Backup: This model includes a battery backup facility requiring 1 x PP3 9v Battery (not included). This ensures the alarm clock continues to function in the event of a power failure to the mains supply. Note: the 9v battery will operate the clock to ensure the alarm still sounds at the correct time, but it will not illuminate the clock display.
Sleep Function
This function allows users to set the radio playback for a predetermined length before it cuts out, useful when going to sleep.
- TOGGLE the function switch to either the OFF or AUTO position.
- PRESS the sleep button. This will turn the radio playback on for a period of 59 minutes AUTOMATICALLY.
- To CHANGE the predetermined time for the sleep function, PRESS and HOLD the sleep button. The clock display will show 00:59. Use the HOUR and MINUTE BUTTONS to CHANGE the length of time that the sleep function operates. The LONGEST time period allowed is 1 hour and 59 minutes (1:59).
- If you wish to CANCEL the sleep function period BEFORE the predetermined time is finished, simply PRESS the snooze button.
Note: The alarm will trigger in the morning by playing back radio audio. Playback will be at the same volume as the radio was left at during sleep mode, so take care not to set the volume too low when operating the sleep function.
Cleaning and Care
MAINTENANCE: This appliance has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper care and regular cleaning.
CLEANING: The exterior surface of the appliance should be wiped with a clean dry cloth only.
? DO NOT use abrasive cleaners, solvents or polish on any part of the appliance.
WEEE/Environmental Protection
DISPOSAL OF ELECTRICAL AND ELECTRONIC EQUIPMENT: ♻️ Do not dispose of this product with household waste. For proper treatment, recovery, and recycling, please take this product to the appropriate waste collection point. If you are unsure where this may be, please contact your local authority. Improper disposal may be harmful to the environment.
PRODUCT END OF LIFE AND BATTERY DISPOSAL: The battery contains substances that may pollute the environment. At end of life for the product, always remove the battery and separate it before you discard the product at your local waste collection point. Both battery and product should be disposed of separately.
If you have trouble removing the battery, then you should contact a qualified technician or authorised service centre.
Contact your local authority for details and locations of official waste collection points. Do not dispose of batteries or product with normal household waste.
Fitting a New UK Plug
Your appliance operates on 220-240V~50Hz AC Mains and comes fitted with a 3-pin BSI Approved plug, ready for use in the UK or Eire. If you need to fit a new plug, the flexible mains lead must be connected as shown below:
IMPORTANT: The wires in the mains lead are coloured according to the following code:
- BLUE: NEUTRAL (N)
- BROWN: LIVE (L)
As the colours of the wires in the mains lead may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:
- The BLUE wire must be connected to the terminal marked "N" or coloured BLACK.
- The BROWN wire must be connected to the terminal marked "L" or coloured RED.
- ? DO NOT CONNECT EITHER WIRE 'L' OR 'N' TO THE EARTH TERMINAL OF A 3-PIN PLUG.
Always ensure that the Mains Cord is located into the Plug through the Cord Guard or Cable Clamp, and that the Cord Guard screws are tightened to clamp the Cord (outer sheath and inner coloured wires) in position in the Plug. Make sure the Plug top is also fitted securely.
The supply cord cannot be replaced. If the supply cord is damaged, the appliance should be scrapped.
This appliance must be protected by a 3 Amp fuse in a 13 Amp type (BS1363) plug. Should you need to replace the fuse, use only an ASTA approved BS1362 fuse.
Customer Services
If you have any queries about this product, please contact Lloytron Customer Services online at:
To find out more about Lloytron products, visit:
Distribution:
Distributed in UK by Lloytron Ltd, Laltex House, Leigh, England WN7 3XH
Distributed in Europe by Laltex Ireland Ltd, Dublin 2, D02 AY86
