EVL001 Electric Vehicle AC Charger User Manual

User Manual for Xiamen models including: ACEVCEVL001, 2A2RN-ACEVCEVL001, EVL001 Electric Vehicle AC Charger, EVL001, Electric Vehicle AC Charger, Vehicle AC Charger, AC Charger

EVL001-User Manual-NA(2024.07.12）

Users Manual

Xiamen Joint Tech. Co., Ltd ACEVCEVL001 2A2RN-ACEVCEVL001 2A2RNACEVCEVL001 acevcevl001

File Info : application/pdf, 11 Pages, 1.19MB

GetApplicationAttachment.html?id=7656696

Electric Vehicle AC Charger
EVL001 Series (NA)-User Manual

1. 142 x 210 mm

70g

108g

6.B

7.mm

EVL(NA)
1:1

Version 2

Electric Vehicle AC Charger
EVL001 Series (NA) -User Manual

USER MANUAL
TABLE OF CONTENTS
1. IMPORTANT SAFETY INSTRUCTIONS ....................................1 2. PRODUCT INTRODUCTIONS....................................................5 3. VERIFY CONTENTS...................................................................7 4. GATHER TOOLS ........................................................................8 5. PLAN THE MOUNTING ..............................................................9 6. MOUNT THE CHARGING STATION ........................................10 7. WIRE THE CIRCUIT ................................................................11 8. LIGHT CODES ..........................................................................12 9. FCC DECLARATION ................................................................13 10. WARRANTY AND MAINTENANCE........................................14

WARNING & CAUTION

USER MANUAL

1. Important Safety Instructions
1.1 Overall Warnings & Cautions
WARNING: To avoid fire, injury or death, carefully read and follow the instructions during installation, operation and maintenance. - DO NOT put fingers into the electric vehicle connector. - DO NOT use this product if the flexible power cord or EV cable is frayed, insulation-broken, or any other signs of damage. - DO NOT use this product if the enclosure or the EV connector is broken, cracked, open, or shows any other indication of damage. - DO NOT remove cover or attempt to open the enclosure because of risk of electric shock. WARNING: This device should be supervised when used around children. WARNING: This device must be grounded. WARNING: To avoid a risk of fire or electric shock, do not use this device with an extension cord. WARNING: The suitability of the use of flexible cord in accordance with CE code, part I, rule 4-012, is to be determined by the local inspection authority. WARNING: To reduce the risk of fire, connect only to a circuit provided branch circuit over-current protection in accordance with the CSA C22.115 Canadian Electrical Code, Part 1 (Canada) or NOM-001-SEDE Electrical installations (utility) (Mexico) or ANSI / NFPA 70 National Electrical Code (USA).

Circuit Breaker Options table

Output Amperage (A)

16A

32A

40A

48A

Circuit Breaker Options (A)

20A

40A

50A

60A

USER MANUAL WARNING & CAUTION
1.2 Installation Requirements
WARNING: Disconnect electrical power prior to installing the charging station. WARNING: Be sure to preview the user manual and ensure local building and electrical codes are reviewed before installing the AC charger. WARNING: The AC charger should be installed by a qualified technician according to the user manual and local safety regulations. CAUTION: Use appropriate protection when connecting to the main power distribution cable. CAUTION: Type B, C or D breaker with the rating current for table should be installed in the upstream AC distribution box. CAUTION: The device shall be mounted at height between 600 mm and 1200 mm from ground. CAUTION: Please keep the charger in a clean area with low humidity. Not recommended to be installed in coastal environments with high humidity or high dust.
1.3 Daily Maintenance
CAUTION: Avoid moisture or water in the charger. If there is water or moisture ingress in the charger, it is necessary to immediately power off to avoid immediate danger, and notify the professionals to carry out maintenance before next use. CAUTION: Please use the charger properly. Do not hit or press hard on the enclosure. If it is damaged, please contact a professional technician. CAUTION: Avoid placing the charger near hot objects and at high temperature locations and away from dangerous substances such as flammable gases and corrosive materials. CAUTION: Do not put heavy objects on the charger to avoid danger.
2

WARNING & CAUTION

USER MANUAL

Circuit Breaker Options table

Output Amperage (A)

16A

32A

40A

48A

Circuit Breaker Options (A)

20A

40A

50A

60A

USER MANUAL

2. Product Introductions
CAUTION: Avoid placing the charger near hot objects and at high temperature locations and away from dangerous substances such as flammable gases and corrosive materials.

2.1 Basic Interface

2.2 Basic Dimension

Led Light Indicator
Lan Cable Inlet

8.661"

3.82"

3.268"

Rear Notch
Charging Cable Inlet
AC Power Cable Inlet

5.040" 0.355"

USER MANUAL

2.3 Specifications

POWER Input Rating Output Current&Power Power Wiring Input Cord Mains frequency Connector Type Ground Fault Detection
Protection
USER INTERFACE Status Indication User Interface Connectivity User Authentication Card Reader Software Update CERTIFICATION & STANDARDS Safety & Compliance Certification Warranty GENERAL Color Enclosure Rating Operating Altitude Operating Temperature Storage Temperature Operating Humidity Mounting Product Dimensions

EVL001

208~240V AC

9.6KW (40A)

11.5 kW (48A)

L1 / L2 / GND

NEMA14-50 Plug

Hard-wire

50 / 60 Hz

SAEJ1772 Type1 18ft (25ft optional)

CCID 20

UVP, OVP, RCD (CCID 20), SPD, Ground Fault Protection, OCP, OTP, Control Pilot Fault Protection

LED indication L-Charge APP Bluetooth, Wi-Fi (2.4G), Ethernet Plug&ChargeaRFID Card (Optional)aAPP RFID (Optional), ISO14443AaISO14443B, 13.56MHz
OTA

UL991, UL1998, UL2231, UL2594 ETL / FCC / Energy Star
2 Year+1 Year extension warranty
BlackaSilver (Customizable) NEMA4 (IP65), IK10 6561ft (2000m)
-22°F ~ +122°F (-30°C ~ +50°C) -40°F ~ +185°F (-40°C ~ +85°C)
5~95% Wall mount 8.66 x 8.66 x 3.82 (220×220×97mm)

USER MANUAL
3. Verify Contents
Check the box to ensure you have this installation guide and these parts:
Electric Vehicle AC Charger Installation Instructions

AC Charger ×1

User Manual ×1

Wall-Mounted Bracket ×1

M5 Anti-Theft Round Head Screws ×2

M6 Hexagonal Expansion Screws ×4

Allen Wrench ×1

Wall-Mounted Bracket

Mounting Template ×1

8 Expansion Screws ×3

Hook ×1

Hooks Bracket

Hook Mounting Template ×1

RFID Card (Optional) ×2

4. Gather Tools
Tools required before installing the Wall-Mounted charger, gather the following tools: 1. Wire stripper 2. Adjustable Wrench 3. Voltmeter or digital multi-meter (for measuring AC voltage at the installation site) 4. Level 5. Pencil or marker 6. Drill

Note: The above tools are very important, please gather them all.

5. Plan The Mounting
WARNING: In areas with frequent thunderstorms, add surge protection at the service panel for all circuits. Ensure all power and ground connections, especially those at the breaker and bus bar, are clean and tight. CAUTION: Not recommended to be installed in coastal environments with high humidity or high dust.

STEP 1 Select the appropriate mounting location with electrical capacity: I. Ensure the owner has chosen a mounting location that allows the charging cable to reach the car's charging port while still providing slack. II. The device must be anchored into mounting such as 2" x 6" stud or a solid wall. III. The device shall be mounted at height between 2 feet (600 mm) and 4 feet (1200 mm) from ground.

STEP 2

12"

Drill 7 Screw Holes with a diameter of 0.35" and

a depth of 2.05" by using 2 mounting templates.

Please drill screw holes in the direction of the template arrow. And use two templates at a

Wall-Mounted Bracket

horizontal distance around 12".

Wall-Mounted Bracket

6. Mount the Charging Station
STEP 1 Use M6 Hexagonal Expansion Screws to secure the wall-mounted bracket, and use 8 Expansion Screws to secure the hook.

STEP 2

STEP 3

Align the rear notch of charger with the wall-mounted bracket and fit the screw holes of the right and left side.

Tighten two M5 anti-theft screws to complete the installation.

7. Wire The Circuit
WARNING: This device must be grounded. Disconnect electrical power prior to installing the charging station.
WARNING: Improper connection of the equipment-grounding conductor would result in a risk of electric shock. Check with a qualified electrician or serviceman if you are not sure whether the product is properly grounded. Do not modify the plug provided with the product if it doesn't fit the outlet, have a proper outlet installed by a qualified electrician.
CAUTION: Use appropriate protection when connecting to the main power distribution cable.

For safe use of electricity, please set circuit breaker protection in the input part of EV Charger. The wiring is not complicated, just need to follow the instructions below:Connect the L1 lead to the grid L1, connect the L2 lead to the grid L2, connect the GND lead to the grid GND.

L1 L2 GND

USER MANUAL
8. Light Codes
8.1 After Start UP

Device Status
Power On Standby Plug The Charging Connector Swipe Card (Optional) Charging In Progress Finished / Stopped Charging Reservation Charging
OTA Device Unavailable
Fault

Light Codes
Blue, green and red blinking alternately Solid Blue Solid Green
Green Blinking Green Breathing
Solid Green Blue, green and red blinking alternately
Blue Breathing Blue Blinking
Red

8.2 Error and Warning Messages

No. Fault Status

Red Light

Remark

Meter Fault

1 flash followed by 3 sec pause

Auto Recover

CP Fault

2 flashes followed by 3 sec pause Unplug the Connector to Recover

UVP

3 flashes followed by 3 sec pause

Auto Recover

OVP

4 flashes followed by 3 sec pause

Auto Recover

OTP

5 flashes followed by 3 sec pause

Auto Recover

OCP

6 flashes followed by 3 sec pause Unplug the Connector to Recover

Ground Fault

7 flashes followed by 3 sec pause Unplug the Connector to Recover

Relay Fault

8 flashes followed by 3 sec pause Unplug the Connector to Recover

RCD Abnormal 9 flashes followed by 3 sec pause Unplug the Connector to Recover

10 RCD Self-Test Fault 10 flashes followed by 3 sec pause

Reboot to Recover

11 Relay Self-Test Fault 11 flashes followed by 3 sec pause
12

Reboot to Recover

USER MANUAL
9. FCC Declaration
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. WIFI moduleContaining FCC ID:2AC7Z-ESP32WROOM32U To satisfy FCC RF exposure requirements, a separation distance of 20cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended.
13

USER MANUAL
10. Warranty and Maintenance
· The warranty period for this charger is two years. · During the warranty period for any malfunction under normal use according to the User Manual and Service Instructions (to be determined by certified maintenance technicians of sellers), the product shall be repaired free of charge. Except for the following situations, the charger shall be subject to the above warranty terms: 1. The warranty certificate cannot be provided or the contents of the warranty certificate are modified or inconsistent with the label indication of the repaired product. 2. Those who are unable to provide valid proof of purchase. 3. Those who exceed the manufacturer's specified warranty period. 4. Those who damage the product due to not following the product service instruction for use, maintenance and storage. 5. Damage or malfunction caused by external object entering. 6. Unauthorized repair, disassembly or modification. 7. Damage caused by force majeure (such as lightning, excessive voltage, earthquake, fire, flood, etc.). 8. Malfunction and damage caused by other unavoidable external factors. Malfunction and damage caused by improper use of equipment, such as water or other solutions entering into the equipment. 9. Malfunction and damage caused by the grid power supply and voltage which is not specified for use with the charger equipment.
The above guarantees shall be made solely, and no other express or implied warranties shall be made (including the implied warranties of merchant ability, particular and applicable reasonableness and adaptability, etc.) whether in the contract, civil negligence, or other aspects, the Company shall not be responsible for any special, incidental or consequential damages.
14

Adobe PDF library 15.00 Adobe Illustrator 24.0 (Windows)