Honeywell Virtual Patent Marking (HON VPM)
IntusiQ - Apple And Samsung Mobile Phones
Smart Home Products and Systems | Resideo
Home | Sipco
ADT 3PS Login
MobileTech
Installation Guide for ADT models including: 8DLWFZWX, CFS8DLWFZWX, ADTZWM, Series Wi-Fi and Z-Wave Module
Ademco Inc. 8DLWFZWX CFS8DLWFZWX CFS8DLWFZWX 8dlwfzwx
File Info : application/pdf, 2 Pages, 540.88KB
DocumentDocumentADTZWM Series Wi-Fi® and Z-Wave® Module Installation and Setup Guide General Information The Communication Module allows the Control Panel to communicate with the WTS700 Wireless Keypad and Amazon Alexa via Wi-Fi. The ADTZWM communications module is intended to provide compatible ADT Control Panels with a Wi-Fi connection as well as connection with and the ability to control Z-Wave devices. The module connects directly to the Control Panel and is powered via the Control Panel's connection. The ADTZWM Series includes models ADTZWM and ADTZWMX. Compatible Control Panels: ADT7AIO/ADT5AIO Series - Installation Guide P/N 800-24121 or higher. ADTHYBWL Series - Installation Guide P/N 800-24125 or higher. ADT2X16AIO Series Installation Guide P/N 800-24341 or higher. NOTE: Control Panel Firmware Release 4.5 or later is required for the ADTZWMX. Installing the Module in the ADT7AIO/ADT5AIO or ADT2X16AIO Series Ensure that all electrical power is removed from the control before installing the module. Unplug the power supply and disconnect the backup battery. 1. Affix the provided FCC/IC label (P/N 800-24286 on the Control Panel's case back (refer to Figure 1). 2. If the Control Panel is not powered up proceed to step 5. If the Control Panel is powered up, it must be powered down as follows: a. ADT7AIO/ADT5AIO or WTS700 Touchscreen At the Advanced screen select "System Shutdown" and confirm. Wait 30-60 seconds. b. ADT2X16AIO or WTP100/WLTP100 Touchpad Enter Master Code + # +* + 9. Wait 30-60 seconds. 3. Unplug the power supply. 4. Disconnect the battery. CONTAINS MODULE: FCC ID: RI7LE910NAV2 IC:5131A-LE910NAV2 CONTAINS MODULE: FCC ID: RI7LE910NAV2 IC:5131A-LE910NAV2 HONEYWELL FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules, and RSS 210 of IC. Operation is subject to the following two conditions: (1) This Device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. FCC ID: CFS8DL-GRIPAIO7 IC: 573F-GRIPAIO7 IC MODEL: GRIPAIO7 800-24167 2/18 Rev A grip-020-V0 Figure 1. FCC/IC Label Location 5. Remove the screw securing the rear case to the front case. 6. Slide the rear case down and separate from the front case. 7. Remove the communication module access cover. 8. Unplug the power supply (if connected). 9. Secure the module with the provided screw. 10. Re-install the communication module access cover. 11. Connect the battery 12. Install the rear case and secure with the screw. 13. Plug the power supply into a 24-hour, 110VAC unswitched outlet. SCREW SCREW grip-011-V0 COVER Installing the Module in the ADTHYBWL Series Figure 2. Installing the ADTZWM Module Ensure that all electrical power is removed from the Control Panel before installing the module. Unplug the power supply and disconnect the backup battery and earth ground. 1. Affix the provided FCC/IC label (ADTZWM, P/N 800-24286) on the ADTHYBWL cabinet (refer to Figure 3) 2. If the Control Panel is not powered up proceed to step 5. If the Control Panel is powered up, it must be powered down as follows: a. WTP100/WLTP100 Touchpad - Enter Master Code + # +* + 9. Wait 30-60 seconds. b. WTS700 Touchscreen At the Advanced screen select "System Shutdown" and confirm. Wait 30-60 seconds. 3. Unplug the power supply. 4. Disconnect the battery and earth ground. CONTAINS MODULE: FCC ID: RI7LE910NAV2 IC:5131A-LE910NAV2 HONEYWELL GRIP HYBRID CONTROLLER FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules, and RSS 210 of IC. Operation is subject to the following two conditions: (1) This Device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. FCC ID: CFS8DL-GRIPH IC: 573F-GRIPH HVIN: GRIPH For Patent Information see: www.honeywell.com/patents Country of Origin: Mexico 800-24232 3/18 Rev A 800-21465 10/15 Rev.A Model LCP500-L ETL Listed Household Fire and Burglar 3091091 Warning Unit Conforms to UL STD 985, 1023, 1635 Classified to ANSI/SIA CP01-2010 TRIGGER 2 12V GND TRIGGER 1 NOT USED SLOT 3 GENERAL } NOT USED THIS EQUIPMENT SHOULD BE INSTALLED IN ACCORDANCE WITH THE NATIONAL FIRE PROTECTION ASSOCIATION'S STANDARD 72 (NATIONAL FIRE PROTECTION ASSOCIATION, BATTERYMARCH PARK, QUINCY, MA 02169). PRINTED INFORMATION DESCRIBING INSTALLATION, TESTING, MAINTENANCE, EVACUATION PLANNING AND REPAIR SERVICE IS TO BE PROVIDED WITH THIS EQUIPMENT. SLOT 1 LTE AUX/BELL_OC LED RUN LED IB2/ACTIVE LED RESERVED LED SLOT 2 WiFi / ZWAVE TAMPER SWITCH RJ-45 CONNECTOR TRIGGER OUTPUT 1: 100mA MAX TRIGGER OUTPUT 2: 100mA MAX BATTERY POWER LED AC POWER LED BATT+ BATT - CONNECTION OF THE FIRE ALARM SIGNAL TO A FIRE ALARM HEADQUARTERS OR CENTRAL STATION SHALL BE PERMITTED ONLY WITH THE PERMISSION OF THE LOCAL AUTHORITY HAVING JURIDICTION. THE BURGLAR ALARM SIGNAL SHALL NOT BE CONNECTED TO A POLICE EMERGENCY NUMBER ZONE 1 USE FOR 2-WIRE SMOKE DETECTORS MAXIMUM NUMBER OF 2-WIRE SMOKE DETECTORS ON ZONE 1 IS 16 2000 2000 OHMS OHMS EOLR EOLR ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 ZONE 7 ZONE 8 HI LO LO HI HI LO LO HI HI LO LO HI HI LO LO HI 8-PIN TRIGGER CONNECTOR AUX OUTPUT LED GND AUX AUX. PWR OUTPUT 10.5-13.8VDC 200mA MAX. (120mA MAX. FOR UL INSTALLATIONS) ALL OUTPUTS ARE POWER LIMITED. 2000 OHMS EOLR 2000 OHMS EOLR 2000 OHMS EOLR 2000 2000 OHMS OHMS EOLR EOLR MAX. ZONE RESISTANCE: (EACH ZONE) 300 OHMS (PLUS EOLR) (USE EOLR PART NUMBER P4100 PART OF KIT SAHDWR1) - 2000 OHMS EOLR ** FOR COMPLETE INFORMATION SEE INSTRUCTIONS 800-24126 OR HIGHER WEEKLY TESTING IS REQUIRED TO ENSURE PROPER OPERATION OF THIS SYSTEM. IN ADDITION, THIS SYSTEM MUST BE CHECKED BY A QUALIFIED TECHNICIAN AT LEAST ONCE EVERY THREE (3) YEARS. +AB 820 OHMS EOLR ALARM OUTPUT 10.513.8VDC, 2A MAX. (600mA MAX. FOR UL USAGE, INCLUDING AUX POWER) STEADY FOR BURGLARY/PANIC, TEMPORAL PULSE SOUNDING FOR FIRE. USE 702 SIREN, OR 12V BELL. SEE INSTRUCTIONS. FOR BELL SUPERVISION, AND CONNECT RESISTOR DIRECTLY ACROSS EXTERNAL SOUNDER. ALARM S TAT U S TROUBLE CANCEL PA N I C 1 OFF 4 MAX 7 I N S TA N T READY AWAY 2 5 TEST 8 CODE 0 STAY 3 6 B Y PA S S 9 CHIME # WTP100 TOUCHPAD 1501 Yamato Road Boca Raton, Florida 33431 © 2018 ADT Security Services ADTHYBWL-Series - Summary of Connections BLACK: TOUCHPAD GND (-) RETURN RED: TOUCHPAD POWER (+) YELLOW: TOUCHPAD IB2A GREEN: TOUCHPAD IB2B DC+ DC - TO INTERNET CONNECTION 24-HR BATTERY STANDBY REQUIRED FOR FIRE INSTALLATIONS. USE 12V, 7AH BATTERY FOR 120mA AUX POWER. SEE INSTRUCTIONS. BATTERY CAPACITY FOR EMERGENCY BURGLARY STANDBY USE AT LEAST 4 HRS. CHARGING VOLTAGE 13.8VDC. MAXIMUM CHARGING CURRENT 650mA. SEALED LEAD-ACID TYPE. BATTERY NORMALLY NEED NOT BE REPLACED FOR AT LEAST THREE YEARS TO DETERMINE TOTAL STANDBY LOAD ON BATTERY, ADD 100mA TO TOTAL OF AUX. POWER AND REMOTE TOUCHPAD CURRENTS BLACK RED EARTH GROUND SEE INSTRUCTIONS** FOR PROPER GROUNDING RECHARGEABLE BATTERY (12V, 7AH) SEALED LEAD ACID TYPE DC+ 300-10211 13.5 VDC, 1.8A POWER SUPPLY TO 10VAC UNSWITCHED OUTLET (24HR) DC - ASSEMBLED IN MEXICO 800-24129 2/18 Rev.A CONTAINS MODULE: FCC ID: RI7LE910NAV2 IC:5131A-LE910NAV2 grip-028-V0 Figure 3. FCC/IC Label Location 5. Install the ADTZWM (ZWAVE) on the edge connector on the PCB (refer to Figure 4). Ensure the receptacle is securely seated on the edge connector. 6. Secure the module with the provided screw. 7. Reconnect the earth ground and battery. 8. Plug the power supply into a 24-hour, 110VAC unswitched outlet. GENERAL EXT INT LTE TX RX GND TX RX GND WiFi BATT+ GND SCREW ADTZWM MODULE grip-012-V0 Programming Figure 4. Installing the ADTZWM Module Note: The ADTZWM requires a router and internet service for Wi-Fi connection. 1. Programming associated with the ADTZWM module as well as the inclusion/exclusion of Z-Wave devices is conducted through ADT 3rd Party Services and the Alarm.com MobileTech tool. On a laptop, PC or Smart Device, go to: https://3ps.adt.com and https://alarmadmin.alarm.com/mobile. Specifications Board Dimensions: Input Voltage Range: Input Voltage: 1.625" W x 2.625" L x 0.3125" D 3.6 14V, Max 17V 3.5V (ADT7AIO, ADT5AIO, ADT2X16AIO) 13.5V (ADTHYBWL) Current Drain: Temperature: 250mA (ADT7AIO, ADT5AIO, ADT2X16AIO) 72mA (ADTHYBWL) 32°F (0°C) to 140°F (60°C) REFER TO THE INSTALLATION AND SETUP GUIDE FOR THE CONTROL WITH WHICH THIS DEVICE IS USED FOR WARRANTY INFORMATION AND LIMITATIONS OF THE ENTIRE SYSTEM. FEDERAL COMMUNICATIONS COMMISSION & ISED STATEMENTS The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. FCC CLASS B STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information: This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · If using an indoor antenna, replace it with a quality outdoor antenna. · Reorient the receiving antenna until interference is reduced or eliminated. · Move the radio or television receiver away from the receiver/control. · Move the antenna leads away from any wire runs to the receiver/control. · Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits. · Consult the dealer or an experienced radio/TV technician for help. Responsible Party / Issuer of Supplier's Declaration of Conformity: Ademco Inc., a subsidiary of Resideo Technologies, Inc., 2 Corporate Center Dr., Melville, NY 11747, Ph: 516-577-2000. ISED CLASS B STATEMENT This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. FCC / ISED STATEMENT This device complies with Part 15 of the FCC Rules, and ISED's license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme à la partie 15 des règles de la FCC et exempt de licence RSS d'ISED. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d'interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une réception indésirable. RF Exposure Warning The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC and ISED multi-transmitter product procedures. Mise en Garde Exposition aux Frequences Radio: La/les antenne(s) utilisée(s) pour cet émetteur doit/doivent être installée(s) à une distance de séparation d'au moins 20 cm (7,8 pouces) de toute personne et ne pas être située(s) ni fonctionner parallèlement à tout autre transmetteur ou antenne, excepté en conformité avec les procédures de produit multi transmetteur FCC et ISEDs. Note: The product should not be disposed of with other household waste. Check for the nearest authorized collection centers or authorized recyclers. The correct disposal of end-of-life equipment will help prevent potential negative consequences for the environment and human health. USE OF THESE PRODUCTS IN COMBINATION WITH NON-HONEYWELL PRODUCTS IN A WIRELESS MESH NETWORK, OR TO ACCESS, MONITOR OR CONTROL DEVICES IN A WIRELESS MESH NETWORK VIA THE INTERNET OR ANOTHER EXTERNAL WIDE AREA NETWORK, MAY REQUIRE A SEPARATE LICENSE FROM SIPCO, LLC. FOR MORE INFORMATION, CONTACT SIPCO, LLC OR IPCO, LLC AT 8215 ROSWELL RD., BUILDING 900, SUITE 950, ATLANTA, GA 303350, OR AT WWW.SIPCOLLC.COM OR WWW.INTUSIQ.COM WARRANTY & SUPPORT For Technical Support, call 1-877-748-7628, option 3 For documentation, call Customer Service at: 1-800-238-2727 (1-800-ADT-ASAP). For the latest warranty information, please go to: www.resideo.com 800-24197D 3/18 Rev. D ADT Security Services 1501 Yamato Road Boca Raton, FL 33431 © 2021 ADT Security Services